PIR&MW ML-89DO User manual

From the detectdistance 4m to12m the detectorwith high sensitivity.
3.2 Installation steps
1. Disassemble:
B.Pull out the bottom of the cover
C.Remove the PCB
A. Loose screw
When power fromexternal DC12V
Standby current 18mA
Alarm current 30mA
The green LEDlight on for3s after poweron,
then flash for2s and light off.Then red
LED flash for15s. 3 minutes after power on,
detector enter stablework status.
Alarm mode: RedLED light on for 3s.
Relay output: N.C
Wireless distance 150m open air
Wireless frequency:433MHZ
Max current whenrecharge battery 120mA
Detect distance:12m 25
Power from buitl-inbattery
Alarm current 18mA
Standby current 80uA
Low battery alarm when battery lowvoltage
it will reportlow voltage. And when battery
voltage recover,itwill report battery
recover again
Relay output N.O If external powercut off
the backup batterywill change the relay output
to N.O modeautomatically 2 minutes after.
Viceversa whenchange from backup battery to
external power
P/N 20091014A03
D.Remove the middle-case
Surface
fixing
45 corner
fixing
D.Put the PCB back on the cover with clips and fasten screws.
C.Fix the base coveron the wall withtwo screws.
B.Draw the cable fromback channel
A.Mark the drilling pointsand make holes.
FT-89R is the best indoor/outdoor motion detector with passive infrared and microwave.It's water proof and all weather resistant with two layer
stable housings..FT-89R combines a variety of detection techniques whichenable it to work in the most difficult environment where needs high
security while maintainingimmunity to false alarm.The infrared sensor adopts nice lens produce three-dimensinal thermal imaging of the protected
area .Combinging thefour-element microwave scanningcontributes to an amazing detection capacity.Using this technique allows high sensitivity
but lowest falsealarm.FT-89R is equipped with unique protection mechanisms against any attempt to damage or to disable its operation.
1.Introduction
Installation Guide of FT-89R
PIR & MW Intelligent Detector
3.Installation
3.1 Guide
Do not face tocold or heat source Do not fact tosun light Keep away from high-
voltage wire
Installation base
should be stable Do not face tometal wall
2. Installation base
Suggest corner mount
ML-89DO
ML-89DO
ML-89DO
ML-89DO

3.3 About mainboard:
Green LED
Pretrigger signal LED
Red LED
Alarm LED
Anti-tamper
switch
Anti-white
light switch
Open loop toswitch on
Short cut toswitch off
Trigger pulse
jumper 1
Trigger pulse
jumper 2
Battery port
Wiring terminal
FT-89Rmainboard
3.4 About pulse jumper:
Trigger pulse jumper 1 setthe #1 IRsensor
2 pulse
1 pulse
3 pulse total open loop
Trigger pulse jumper 1 setthe #1 IRsensor
3.5 Wiring terminal
+-
AlarmTamp 12V
PowerAlarm
Anti-tamper
Alarm: Afterexternal power keep for 2-10 minutes,alarm
output will beN.C mode.
Alarm: Afterexternal power cut off for 2-10minutes, alarm
output will changeto N.O.and keep working under
low consumption wirelessmode.
3.6 Wireless coding
Set the alarmcontrol panel at coding mode, then
press the anti-tamperswitch of FT-89R for 3sthen release.
Youwill hear the alarm panel sound code successfully.
2 pulse
1 pulse
3 pulse total open loop
3.8. Stand-by battery replacing and using
When battery islower power, it will send related signal
to control panel,souser should replace battery with
same spec.(as rightfig.)
AA
AA
AA
AA
AA
On BUS workingmode,if this model of detector more than
4pcs in thesystem,you need put battery inside to assure
the system willnot overload.
3.7 Perform motion test to the detection area: ins tall the cover and close the fasten part
(refer to the right diagram)
1. Start thetest at least 2 minutes after power supply
2. Crossing toany direction of the detection area, your walking with 0.75m/s between 3mdistance will causethe LED
indicator to lightfor 2-3 seconds (refer to the right diagram)
3 .Perform motiontest from contrary directions in order to confirm theboundary of twosides. Make
confirmed that detectioncenter pointing to the center of protected area.
lower limit ofPIR detection.
4.the center ofdetection zone should not uphill incline. To obtain a gooddetection range ,please adjust
the vertical detectionrange, en-sure the detector is in a correct position.
5. AfterMW sensitivity ordetection angle areadjusted, walking test must be performedaccording to the above steps.
Do the samestep to confirm the upper limit.
ML-89DO