PITH & STEM DropTop Duo 27 User manual

Page: 1
www.pithandstem.com
DropTop.™ Duo 27 Light Instructions
© 2023 Pith & Stem ltd. All rights reserved.

Page: 2
DropTop.™ Duo 27 Light Instru tions.
Fixings Pa ks
Tools
12 3 45
678910
x17 x19
x8
x8
Brick/Concrete Wall
Fixings Plasterboard Wall Fixings
x8
x8 x5 x5
For a Plasterboard Wall
*Not included
25mm hole saw or a 25mm Spade bit
*included *Not included

Page: 3
DropTop.™ Duo 27 Light Parts
DL
C
DL
A
DL
B
DL
D
DL
E
DL
F
DL
G
DL
H

Page: 4
DropTop.™ Duo 27 Light dimensions.
141 m
67 m 10 m
14 m
71 m
55 m
143 m
58 m
10 m
Exterior dimensions when Closed:
Height: 71 m
Width: 143 m
Depth: 15.8 m
Worktop Dimensions:
Width: 143 m
Depth: 55 m
Weight - 35kg
It is re ommended to have
two people for safely
mounting your DropTop.
!
The Duo 27 Light supports up
to 50kg in weight

Page: 5
130 m
41 m
10 m
The Duo 27 Light is designed to
house dual 27-in h monitors.
Available Monitor Spa e dimensions:
Height: 41 m
Width: 130 m
Depth: Please see note below*
DropTop.™ Duo 27 Light Monitor spa e dimensions.
Monitor Mount Depth available
Extendable 5cm
Tilt 6cm
Slim 8cm
!Please note that the
available monitor spa e
depth will vary based on your
hosen Monitor Mount

Page: 6
Monitor Mounts.
Your DropTop™ Light will in lude one of the following monitor bra kets, depending on your order.
Slim Mount
Depth: 1.3 m
Tilt Mount
Depth: 3.3 m
Extendable Arm Mount
Depth: 5 m
!Make sure your monitor is VESA ompatible
with 75x75mm or 100x100mm. Also, please
note the re ommended monitor depth for
ea h mount.
The re ommended
maximum depth
for your monitor is 5 m
The re ommended
maximum depth
for your monitor is 8 m
The re ommended
maximum depth
for your monitor is 6 m

Page: 7
DropTop.™Duo 27 Light Wall Plate dimensions.
90 m
15.7 m
2 m
3.7 m

Page: 8
Page: 8
1.6 m
The Duo 27 Light is designed with
a ba k re ess depth of 1.6 m. This
allows for any ables to be fed
tidily behind the DropTop
It is re ommended to feed the
monitor's power able through
round able management
grommet and down between the
gap to keep it tidy.
5.5 m
DropTop.™Duo 27 Light Cable Management

Page: 9
2
3
Fixings Pack #2
DL
F
DL
E
DL
G
1Fixings Pack #1
x1
DL
F
DL
E
DL
G
DropTop.™ Duo 27 Light Assembly
Page: 9

Page: 10
3
DL
F
DL
E
DL
G
DL
B
Front View Ba k View
Front
DL
BDL B
At this step, make sure to position Part B at the
front view instead of the back, as shown above.
x
4
Fixings Pack #3
x12
Fixings Pack #1
x4
DL
D
DL
C

Page: 11
5
Fixings Pack #2
x4
DL
C
DL
D
DL
F
DL
E
DL
G
DL
B
6
Fixings Pack #1
x4
Fixings Pack #3
x3
DL
A

Page: 12
7Fixings Pack #4
x4
DL
A
8
Fixings Pack #2
x4
DL
C
DL
D
DL
FDL
E
DL
G
DL
A
DL
B

Page: 13
Fixings Pack #2
x4
Fixings Pack #2
10
DL
D
DL
B
DL
H
DL
F
9
Fixings Pack #2
x4
Fixings Pack #3
x7
Ba k View
DL
A
DL
D
DL
B

Page: 14
11
Fixings Pack #7
X4
Fixings Pack #7
x6
Fixings Pack #8
x2
12
Cable management grommet.
Insert the two thin
metal disks into the
black oval-shaped
ring.
DL
E

Page: 15
13
Matching colour cover cap stickers have
been provided with your DropTop.™
Apply the cover caps over any exposed
screws.
14
After your DropTop is mounted, the speed of
the soft opening feature can be adjusted.
Locate the ridged surface at the end of each
stay to make adjustments.
To increase the speed
of the soft opening
feature, turn the
ridged surface at the
end of each stay anti-
clockwise
To slow down the soft
opening speed, turn
the ridged surface
clockwise at the end
of each stay.

Page: 16
2
Attach the screen mount to the monitor using
the screws that were provided.
Monitor Back
View
x 4
To install your monitor on a Slim or Tilt Mount
1
Your DropTop.™ comes with either a Slim
Monitor Mount or a Tilt Monitor Mount,
depending on your chosen conguration.
Slim Monitor Mount
Tilt Monitor Mount

Page: 17
3
Insert your monitor into the desk and t the
monitor bolts into the screen mount loosely. Adjust
the screen mount to the desired height, then
tighten the bolts.
Front View
Back View
x2
4

Page: 18
To install your monitor on an Extendable Arm Mount
2x VESA Plate-b 2x Wall Plate &
Articulating Arms-A
8x M4 Bolt - f 8 x M4 Bolt - d 4 x M6 Bolt
Wrench-c
This way up.
4 x M4 Bolt-f
This way up.
Carefully place your monitors face down on a
clean, at surface. Attach the VESA Plate-b to the
back of your monitor using the M4 Bolts-f
provided.
21

Page: 19
3
Attach the Wall Plate & Articulating Arms-A to the
VESA slot on the back of the DropTop, using the 2 x
M6 bolts provided.
4
4 x M6
Bolt
Front View
Ba k View
Wall Plate &
Articulating Arms-A
Fully extend the articulating arms out.

Page: 20
Hook the VESA Plate-b to the Socket on
the fully extended arms.
Secure the VESA
Plate-b to the
articulating arm using
the 2x M4 Bolt-d
provided.
Use the wrench
provided to adjust the
tilting angle of the
VESA Plate-b.
2 x M4 Bolt - d
56