PITH & STEM DropTop Classic User manual

1
DropTop.™ Max Classic Instructions.
© 2023 Pith & Stem ltd. All rights reserved.
DropTop.™

2
2
DropTop.™ Max Classic I structio s
Fitti gs Packs
Tools
Power cable supplied with your DropTop
will vary based on your order.
8910
Brick/Concrete Wall
Fixings Plasterboard Wall Fixings
x3 x3
x6
x6
UK PLUG EU PLUG USA PLUG AU / NZ PLUG
25mm hole saw or a 25mm Spade bit
For a Plasterboard Wall
*included *Not included*Not included
Cable Management Grommet
2 x VESA Plate-b
2 x Wall Plate &
Articulating Arms-A 8 M4 Bolt - f
4 x M4 Bolt - d
4 x M6 Bolt

3
3
DropTop.™ Max Classic.
No Mo itor
Compatible Mo itors Sizes:
27-i ch Mo itor
34-i ch Ultrawide Mo itor
I tegrated Mo itor
34-i ch Ultrawide Mo itor
DropTop.™
DropTop.™

Weight - 40kg
It is recomme ded to have
two people for safely
mou ti g your DropTop.
!
73cm
102cm
88cm
62cm
10cm
11cm
13cm
59cm
30cm
DropTop.™ Max Classic dime sio s.
Exterior dime sio s whe Closed:
Height: 73cm
Width: 102cm
Depth: 16.5cm
Worktop Dime sio s:
Width: 102cm
Depth: 62cm
3.5cm
The Max Classic supports up to
75kg i weight

59cm
84cm
2.5cm
11cm
38cm
5cm
5cm
6cm
DropTop.™ Mo itor space dime sio s
The Max Classic is designed to house
a 27-inch Monitor or a
34-inch Ultrawide monitor.
Available Mo itor Space dime sio s:
Height: 38cm
Width: 84cm
Depth: 6 cm
Mou t Bracket Depth
Depth: 5cm
Recomme ded maximum depth
for your mo itor is 6 cm.
I choosi g a mo itor for your
DropTop Max Classic, it is
importa t to co sider both the
depth of your mo itor a d the
depth of the mou t bracket to
e sure that they do ot exceed
11cm i total depth.
!

75mm 100mm
75mm
100mm
75mm
E sure your mo itor is VESA compatible
with 75x75mm or 100x100mm.
!
O e exte dable mo itor mou ts is i cluded with
your DropTop Max Classic, providi g tilt, swivel,
a d rotatio fu ctio ality.
Exte dable Arm Mo itor Mou t
180º Swivel
180º Swivel
Tilt 15º
Rotate 360º
180º Swivel

DropTop.™ Max Classic Wall Plate dime sio s.
50cm
10.4cm
2.3 cm
2.1cm

8
Electrical wiri g is embedded i to
the back of your desk. Take care
ot to drill or damage a y
embedded wires while i stalli g
your desk.
!
DropTop Electrical Wiri g

9
12
If you have selected the "No Monitor" option,
your DropTop™ will come with an Extendable
Arm Monitor Mount.
No mo itor optio DropTop.™
Installing your monitor.
VESA Plate-b Wall Plate & Articulating
Arms-A
4x M4 Bolt - f 2 x M4 Bolt - d 2 x M6 Bolt
Wrench-c
This way up.
4 x M4 Bolt-f
This way up.
Carefully place your monitors face down on a
clean, at surface. Attach the VESA Plate-b to the
back of your monitor using the M4 Bolts-f
provided.

10
3
Attach the Wall Plate & Articulating Arms-A to the
VESA slot on the back of the monitor, using the 2 x
M6 bolts provided.
4
2 x M6
Bolt
Fro t View
Back View
Wall Plate &
Articulating Arms-A
Fully extend the articulating arms out.
DropTop.™
DropTop.™

11
Hook the VESA Plate-b to the Socket on
the fully extended arms.
Secure the VESA
Plate-b to the
articulating arm using
the 2x M4 Bolt-d
provided.
Use the wrench
provided to adjust
the tilting angle of
the VESA Plate-b.
2 x M4 Bolt - d
56

12
To adjust the height of the mount along the VESA
slot, slightly loosen the M6 bolts on the back, then
reposition the mount to the desired height and
tighten the bolts again.
Back View
78
The mount bracket should be positioned as
indicated in the diagram to ensure proper and
mounting of the monitors.
Left

13
Cable Ma ageme t
Before mounting your DropTop onto the wall,
connect any cables to your monitor and feed
them through the oval cable management
grommet to keep them tidy.
The central shelf housing contains the
electrical cable that powers your
DropTop.
To access it, remove the screws from
the wood cover.
DropTop.™

14
The central shelf housing can be used
to hide extra cables or pass through a
wired Ethernet cable, if needed.
To re-attach the wood cover, screw in
the screws.

15
Mou ti g the Wall plate.
The height to install the wall plate should be
measured from the top of the desired desk
height to the top of the recessed area of the wall
plate.
54cm
54cm
DropTop.™ Max
Wall plate height.
Your DropTop.™ desk can be installed at any
height that best suits your needs and
preferences.
Depending on your preferred sitting position,
you can install your DropTop™ on the wall
between 65cm and 80cm.
Worktop Height
Floor
Wall plate Height
Your preferred desk
height.
DropTop.™
DropTop.™

16
54cm
I stalli g o a brick a d co crete wall.
x6
Use the wall plate as a guide and mark the
position of the xing holes with a pencil.
The height to install the wall plate should be
measured from the top of the desired desk
height to the top of the recessed area of the wall
plate.as previously explained.
12
Drill 6 x 8mm sized holes.
Wall

17
4
x6
3
Fittings Pack #9
To safely mount the desk, ensure that the
DropTop.™ is locked before lifting it onto the
wall plate. The DropTop.™ should t snugly in
the recess of the wall plate.
Wall
DropTop.™

18
DropTop.™
Wall
5The securing screws in ttings pack #8
will ensure that your desk does not
accidentally come off its wall mount.
DropTop.™
Front View
After the DropTop.™ desk has been
mounted on the wall, open the desk and
use a long thin tool or pencil to mark the
position of the mirror screw holes.
To safely remove the desk from the wall,
make sure that the DropTop.™ is locked
before lifting it off the wall plate.
6

19
87
Drill the 2 x 6mm holes previously marked
for the mirror screws and insert the wall
plugs.
To safely mount the desk , make sure that the
DropTop is locked before lifting it onto the wall
plate.
DropTop.™
x2
Fitti gs Pack #8
Wall

20
Fitti gs Pack #8
910
The detachable power cable
is connected to the base of
your desk.
Screw the mirror screw
caps.
x2
UK PLUG EU PLUG USA PLUG AU / NZ PLUG
DropTop.™
DropTop.™