Pittsburgh Automotive 61282 Original instruction manual

Page 2 For technical questions, please call 1-888-866-5797. Item 61282
SAFETY OPERATION MAINTENANCESETUP
Table of Contents
Safety ......................................................... 2
Setup .......................................................... 3
Operation.................................................... 4
Maintenance............................................... 5
Parts List and Diagram............................... 7
Warranty ..................................................... 8
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Failure to heed these markings may result in personal injury and/or property damage.
1. Study, understand, and follow all instructions
before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces.
4. Lifting device only. Immediately after lifting,
support the vehicle with appropriate means.
5. Do not move or dolly the vehicle while on the jack.
6. No alterations shall be made to this product.
7. Never work on, under or around a load
supported only by this device.
8. Do not adjust safety valve.
9. Wear ANSI-approved safety goggles and
heavy-duty work gloves during use.
10. Keep clear of load while lifting and lowering.
11. Lower load slowly.
12. Apply parking brake and chock
tires before lifting vehicle.
13. Lift vehicle only at manufacturer
recommended locations.
14. Inspect before every use; do not use
if parts are loose or damaged.
15. Do not use for aircraft purposes.
16. The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that may occur.
The operator must understand that common sense
and caution are factors, which cannot be built into
this product, but must be supplied by the operator.
17. The brass components of this product contain lead,
a chemical known to the State of California to cause
cancer, birth defects (or other reproductive harm).
(California Health & Safety code § 25249.5, et seq.)
IMPORTANT! Before first use:
Check hydraulic fluid level and fill to 1/4″ below
the top of the Fill Port as needed - see instructions
on page 4. Thoroughly test the Jack for proper
operation. If it does not work properly, bleed air from the
hydraulic system - see instructions on on page 3.
SAVE THESE INSTRUCTIONS.

Page 3For technical questions, please call 1-888-866-5797.Item 61282
SAFETYOPERATIONMAINTENANCE SETUP
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the following pages,
refer to Parts List and Diagram on page 7.
Tool Set Up
Attaching the Handle
1. Attach the Upper Handle to the Lower Handle.
2. Loosen the Set Screw and insert the
assembled Handle into the Handle Socket.
3. Tighten the Set Screw.
Functions
Hydraulic
Unit
Fill
Screw
Safety Valve
Cover
DO NOT OPEN
OR ADJUST
Saddle
Lifting
Arm Handle
Handle
Socket
Rear
Caster
Set
Screw
Cover Plate
(remove
to access
Fill Screw)
Front
Wheel
Figure A

Page 4 For technical questions, please call 1-888-866-5797. Item 61282
SAFETY OPERATION MAINTENANCESETUP
Operating Instructions
Bleeding
1. Remove the Cover Plate.
2. Loosen the Fill Screw.
3. Turn the Handle counterclockwise
to open the Release Valve.
4. Pump the Handle up and down quickly several
times to purge air from the system.
5. Check oil level and add as
explained below, if needed.
6. Tighten the Fill Screw and replace the Cover Plate.
Adding Oil
1. Remove the Cover Plate.
2. Remove the Fill Screw.
3. Add high grade hydraulic fluid slowly until the
oil reaches 1/4″ below the top of the Fill Port.
Note: Do not touch the Handle when
adding the hydraulic fluid.
4. Replace the Fill Screw and replace the Cover Plate.
Lifting
Park vehicle on a flat, level, solid, surface safely away from oncoming traffic. Turn off the vehicle’s
engine. Place the vehicle’s transmission in “PARK” (if automatic) or in its lowest gear (if manual).
Set the vehicle’s emergency brake. Then, chock the wheels that are not being lifted.
1. Slowly turn the Handle counterclockwise
to lower the Jack. Once the Jack is fully
lowered, turn the Handle firmly clockwise.
2. Carefully position the Saddle of the Jack under
the vehicle manufacturer’s recommended lifting
point. (See vehicle manufacturer’s owner’s
manual for location of frame lifting point.)
3. Pump the Handle until the top of the Saddle has
nearly reached the vehicle’s lifting point. Position
the Saddle directly under the vehicle’s lifting point.
4. To lift the vehicle, pump the Handle.
Use smooth, full strokes.
5. Select jack stands (not included) of appropriate
capacity. Set the jack stands to the same height
according to the manufacturer’s instructions,
making sure they lock securely into position.
6. Position the saddles of the jack stands
under the vehicle manufacturer’s
recommended support points.
WARNING! Ensure that the vehicle support
points are fully seated in the saddles of both
jack stands. Use a matched pair of jack stands
per vehicle to support one end only.
7. Slowly turn the Release Knob counterclockwise to
lower the vehicle onto the saddles of the jack stands.
8. Once the vehicle is fully seated on the
jack stands, continue slowly lowering the
Jack until it is completely lowered.
9. Remove the Jack and store safely out of the way.
Lowering
1. Carefully remove all tools, parts, etc.
from under the vehicle.
2. Position the Saddle under the lifting point.
Turn the Handle firmly clockwise and raise the
vehicle high enough to clear the jack stands.
3. Carefully remove the jack stands.
4. Slowly turn the Handle counterclockwise
to lower the vehicle onto the ground.
5. Lower the Jack completely. Store the
Jack indoors out of children’s reach.

Page 5For technical questions, please call 1-888-866-5797.Item 61282
SAFETYOPERATIONMAINTENANCE SETUP
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. Before each use, inspect the general condition
of the Jack. Check for broken, cracked, or bent
parts, loose or missing parts, and any condition
that may affect the proper operation of the tool.
If a problem occurs, have the problem corrected
before further use.
Do not use damaged equipment.
2. Before each use, thoroughly test the Jack
for proper operation prior to its actual use.
If the Jack appears not to be working properly,
follow Bleeding instructions on page 34.
3. Change the hydraulic fluid at least
once every three years:
a. With the Jack fully lowered, remove the
Cover Plate and the Fill Screw.
b. Tip the Jack over to allow the old hydraulic fluid to
drain out completely. Dispose of the old hydraulic
fluid in accordance with local regulations.
c. With the Jack upright, completely fill the
Hydraulic Unit with high grade hydraulic fluid
until the oil is 1/4″ below the top of the Fill Port.
d. Turn the Handle counterclockwise
to open the Release Valve.
e. Pump the Handle up and down quickly
several times to purge air from the system.
f. Recheck fluid level and re-fill as needed.
g. Replace the Fill Screw and Cover Plate.
4. Wipe dry with a clean cloth. Store the
Jack indoors out of children’s reach.

Page 6 For technical questions, please call 1-888-866-5797. Item 61282
SAFETY OPERATION MAINTENANCESETUP
POSSIBLE SYMPTOMS
PROBABLE SOLUTION
(Make certain that the Jack is not supporting a load
while attempting a solution.)
Jack will
not lift at
its weight
capacity
Saddle
lowers
under
load
Pump
stroke
feels
spongy
Saddle
will
not lift
all the
way
Handle
moves
up when
jack is
under
load
Oil
leaking
from filler
plug
X X Check that Release Valve is fully closed.
Jack may require bleeding - see instructions on page 4.
X X X
Valves may be blocked and may not close fully. To flush the valves:
1. Lower the Saddle and securely close the Release Valve.
2. Manually lift the saddle several inches.
3. Open the release valve by turning the Handle counterclockwise.
and force the saddle down as quickly as possible.
XX X
Jack may be low on hydraulic fluid. Check the fluid level
and refill if needed - see instructions on page 4.
Jack may require bleeding - see instructions on page 4.
XUnit may have too much hydraulic fluid inside, check fluid
level and adjust if needed - see instructions on page 4.
Troubleshooting
TO PREVENT SERIOUS INJURY:
Use caution when troubleshooting a malfunctioning jack. Stay well clear of the supported load.
Completely resolve all problems before use. If the solutions presented in the Troubleshooting guide
do not solve the problem, have a qualified technician inspect and repair the jack before use.
After the jack is repaired: Test it carefully without a load by raising and lowering it fully,
checking for proper operation, BEFORE RETURNING THE JACK TO OPERATION.
DO NOT USE A DAMAGED OR MALFUNCTIONING JACK!
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.

Page 7For technical questions, please call 1-888-866-5797.Item 61282
SAFETYOPERATIONMAINTENANCE SETUP
Parts List and Diagram
Part Description Qty
1 Retaining Ring 19 2
2Washer 2
3Front Wheel 2
4Side Plate Assembly 1
5Rear Caster 2
6Spring Washer 10 4
7Screw (M10x20) 4
8Spring Washer 16 4
9Nut M16 2
10 Locking Nut M16 2
11 Tie Rod 2
12 Bolt (M8x20) 4
13 Spring Washer 8 4
14 Bolt 2
15 Spring Washer 18 2
16 Retaining Ring 25 2
17 Bushing 2
18 Cover Plate 1
19 Screw (ST4.8x13) 4
20 Lift Arm Shaft 1
Part Description Qty
21 Bolt 2
22 Long Linkage 2
23 Lift Arm Assembly 1
24 Retaining Ring 16 2
25 Saddle 1
26 Saddle Screw 1
27 Retaining Ring 22 2
28 Hydraulic Adaptor 1
29 Spring 2
30 Split Pin (4x45) 1
31 Hydraulic Unit 1
32 Retaining Ring 12 1
33 Handle Socket 1
34 Spindle 1
35 Roller 1
36 Handle Bolt 1
37 Lower Handle 1
38 Bolt (M6x35) 1
39 Upper Handle 1
40 Foam Handle Bumper 1
1
2
3
3
2
1
4 5
678
9
8
10
11
12
13
14
15
12
13
16
1117
18
19
16
20
21
22
23
24
25
26
27
28
29
30 31
32 33
34
35
36 37
38
39
27
40

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • [phone]
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.