PITTSBURGH MOTORCYCLE 57775 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Lift Table not included.
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 21h
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2021 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service ma y n o t b e i n c l u d e d .
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. 60536
SAFETY OPERATION MAINTENANCEASSEMBLY SAFETY OPERATION MAINTENANCESETUP
Table of Contents
Safety ......................................................... 2
Setup .......................................................... 3
Operating Instructions ................................ 4
Maintenance............................................... 5
Parts List and Diagram............................... 6
Warranty ..................................................... 8
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
Failure to heed these warnings may result in personal injury and/or property damage:
1. Study, understand, and follow all instructions
before operating this device.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during use.
3. Inspect before every use; do not use
if parts are loose or damaged.
4. Secure load with appropriate restraint device.
5. No alterations shall be made to this product.
6. Stay alert. Watch what you are doing, and use
common sense when operating a Lift. Do not use
Lift while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while
operating lifts may result in serious personal injury
7. Before use, read manufacturer’s instruction
manual for the ATV or motorcycle being lifted.
8. When servicing the Vise, use only identical
replacement parts - refer to attached, product-
specific parts lists and diagrams. Follow instructions
in the “Maintenance and Servicing” section of this
manual. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of injury.
9. Maintain labels and nameplates on the Vise. These
carry important information. If unreadable or missing,
contact Harbor Freight Tools for a replacement.
10. The warnings, precautions, and instructions
discussed in this manual cannot cover all
possible conditions and situations that may occur.
The operator must understand that common sense
and caution are factors, which cannot be built into
this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
Specifications
Maximum Tire Width 170mm

Page 3For technical questions, please call 1-888-866-5797.60536
SAFETYOPERATIONMAINTENANCE ASSEMBLY SAFETYOPERATIONMAINTENANCE SETUP
ASSEMBLY
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the
parts listed in the following pages, refer to the
Assembly Diagram at the end of the manual.
1. Remove existing clamp, if installed, from platform.
2. Identify the drilling guide sheets, named
“Drill Guide 1” and “Drill Guide 2.” Carefully
align the white/solid holes in the Guides
with the existing wheel clamp mounting
holes of the platform as shown below.
3. Attach the guide sheets to the platform using
the adhesive at the four corners of the guides.
Note: Make sure Drill Guides are parallel to lift table and
that holes align properly before drilling. Use a light below
the platform if needed to better align the existing holes.
4. Use a 12.5 mm (or 1/2 in.) metal drill
bit (not included) in a power drill (not
included) to make the holes.
Note: Make sure there are no obstructions
beneath platform before drilling.
5. Place bit in center of black solid holes on guide
sheets and drill through platform - 16 holes total.
6. Remove guide sheets.
7. Use a tool to unscrew and remove the Nut and
Washer holding the Handle. Position the Handle in
opposite direction and reinstall with the Washer and
Nut.
Nut
Washer
8. Attach the Movable Jaw Sliding Tube (10) to the
Movable Vise Jaw Assembly (11) with four M8x16
bolts (9).
9
M8X16 Bolts
11
Movable
Vise Jaw
Assembly
10
Sliding Tube

Page 4 For technical questions, please call 1-888-866-5797. 60536
SAFETY OPERATION MAINTENANCEASSEMBLY SAFETY OPERATION MAINTENANCESETUP
ASSEMBLY (continued)
Operating Instructions
1. Refer to the Motorcycle Lift instructions
to load motorcycle onto the platform.
2. Push the motorcycle forward until it contacts
the Baffle and is against the Fixed Vise Jaw.
3. Turn Handle to bring the Movable Vise Jaw against
the wheel, securing motorcycle in upright position.
4. Secure the motorcycle to your Lift platform
with belts or straps (not included).
9. Insert Baffle Assembly (22) into
Fixed Vise Jaw Assembly (18) and secure with Pin
(20).
20
Pin
22
Baffle Assembly
10. Mount final assemblies to the platform with
M10x25 Bolts (10), Washers (6) and Nuts
(14). Use either set of holes as needed.
Usage shown above.
Wheel and Lift not included.
18
Fixed
Vise Jaw
Assbly

Page 5For technical questions, please call 1-888-866-5797.60536
SAFETYOPERATIONMAINTENANCE ASSEMBLY SAFETYOPERATIONMAINTENANCE SETUP
Maintenance and Servicing
Procedures not specifically explained in this manual must be performed only by a
qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment.
If abnormal noise or vibration occurs, have the problem corrected before further use.
1. BEFORE EACH USE, inspect the general condition
of the tool. Check for loose screws, misalignment
or binding of moving parts, cracked or broken
parts, and any other condition that may affect its
safe operation. Do not use damaged equipment.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts. Specify UPC 193175422163 when ordering parts.

Page 6 For technical questions, please call 1-888-866-5797. 60536
SAFETY OPERATION MAINTENANCEASSEMBLY SAFETY OPERATION MAINTENANCESETUP
Parts List and Diagram
Parts List
Part Description Qty
1 Screw 1
2 Handle 1
3 Nut 1
4 Wheel Clamping Handle 1
5 Nut 1
6 Flat Washer 11
7 Screw 1
8 Movable Jaw Holder 1
9 Bolt M8x16 4
10 Movable Jaw Sliding Tube 1
11 Movable Vise Jaw Assembly 1
Part Description Qty
12 Wheel Clamp Pipe Plug 4
13 Rubber Board-II 2
14 Nut 10
15 Bolt M10x25 10
16 Rubber Board-1 2
17 Screw 24
18 Fixed Vise Jaw Assembly 1
19 Latch Ring 1
20 Pin 1
21 Plug 2
22 Baffle Assembly 1

Page 7For technical questions, please call 1-888-866-5797.60536
SAFETYOPERATIONMAINTENANCE ASSEMBLY SAFETYOPERATIONMAINTENANCE SETUP
Assembly Diagram

26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.