Pixel LV-122 User manual

Made in China
50150 V10.02
This manual is current update of 1st August, 2010.
Please contact to PIXEL service center for further
information, if interesting of the combining usage with
products released after this day.
En
中文
Wired Live View Remote Control
Http:// www.pixelhk.com
PIXEL .INC
LV-122

Contents
13
20
01
02
03
04
05
08
08
09
11
12
Overview
LV-122 features
Cautions before use
Included items
LV-122 the name of each part
How to use LV-122
Install battery
Connecting Device
Use LV-122
Live View
Shooting
Device charge
21
PIXEL LV-122 Specifications
En

2
1
Overview Cautions before use
First of all, thank you for purchasing the high-performance PIXEL product LV-
122, which can monitor the scope of camera lens by wired real-time control, Which
support single ,1st continuous, [ BULB] and delay shooting. It will be good assist on
the condition that you are inconvenient to wait for shooting and get the photo from
camera lens.
Please completely read this product and camera manuals before use this product;
make sure you can familiar to control and use it correctly. You can easily to
understand “how to use” and “condition” from this instruction manual.
Make sure the camera and LV-122 are powered off before install device.
As this is an electronic product accessory; some of the environment causes may affect the
working. However this is hardly ever to get this situation.
When connected the remote cable with the device, do not pull the wires.
This product can't be strong vibration, or may lead to product failure.
For a long time non-use, please turned off the product’s power and remove the battery.
Do not put it in high temperature, such as a closed car under direct sunlight, the control panel
and other high-temperature areas.
Keep dry, do not use wet hand contact with the product, the product must not be immersed in
water or exposed to rain, and this may lead to not work properly.
Do not use flammable gases in violation of this warning may cause an explosion or fire.
Because this product include battery, regarding how to use and charge battery, please
operate it strictly according to related rules, otherwise may cause explosion, fire or physical
injury.
EnEn

中文
LV-122 features Included items
4
3
LV-122 getting the image from lens, we guarantee the shooting range and result
same as the camera.
Real-time monitor the scenes captured by camera lens.
Support single, 1st continuous, BULB and delay shooting.
With 3.0-inch TFT display and the resolution is 960×240, which can adjust the
brightness.
Use 3.7V 1200mAh chargeable lithium battery which is energy-saving and
environmental protection.
With great compatibility which can change connecting cable to be suitable for
different cameras.
Please check all included items after open the packing, and PIXEL LV-122
with the following items:
LV-122 1PC
1
2
3
BL-6F lithium battery 1PC
4
AC-5E
Charger 1PC
USB charging cable
1PC
5Connecting cable CL-17 1PC
6Manual 1PC
7
EnEn

The name of each part
6
5
The name of each part
LV-122
1
2
3
8
9
7
OFF
ON
10
12
11
4
5
6
g
h
j
m
c
d
f
i
k
l
a
b
e
EnEn
Video output socket
1 2
4
3
65
7 8 9
10 11 12
Charging socket
Function button Function indicator Function icon
Shutter release button Shutter indicator Charge indicator
Battery hatch Lock release button Power switch
Mini USB socket
Function icon, indicator and button
Icon for single shoot
a
Icon for 1st continuous shoot
b
Icon for delay shoot
d
cIcon for [ ] shoot
eIndicator for single shoot
fIndicator for continuous shoot every second
hIndicator for delay shoot
gIndicator for [ ] shoot
iScreen intensity+
jButton for right move
lButton for left move
kScreen intensity-
mOn/off for screen

The name of each part
78
How to use LV-122
Install battery
OFF
ON
EnEn
1. Press the lock release button on the end of battery hatch, and
slide battery hatch to open it.
2. Install the battery in place according to the figure.
Put one end of the battery with metal contact which will match with
metal probe in the battery socket and then press the other end.
3. Close the battery hatch.
BL-6F lithium battery standby time over than 500 hours. Working
time more than 4 hours when open the LCD display.
When the battery power is low, the charge indicator keeps twinkle,
Wired live view remote control needs to replace batteries or
recharge as soon as possible to ensure normal shooting.
CL-17 Connecting cable
Charge plug
Mini USB plug AV plug
Shutter plug
USB plug
AC-5E Charger

How to useLV-122
9
How to useLV-122
10
Turn on the power
Slide Power switch to [ON] to turn on wired Live view remote
control (LV-122) and to [OFF] to turn off it.
When battery power is low, the charge indicator will flash red.
Turn on display screen
When you turn on wired Live view remote control, the default
mode of LCD is off and you can turn it on by pressing LCD
button. You can turn off by pressing it again.
Connect with camera
EnEn
LV-122
1. Make sure camera and remote are turned off. Open camera shutter
plug protective cover and put the shutter plug of connecting cable CL-
17 in place, then make sure it has been fixed firmly.
For most of camera shutter socket, there is mis-plug interface, please note
insert direction so as to avoid damage to shutter socket and cable socket.
Different CL-17 cable shutter plug will match with different camera.
2. Open AV socket protective cover and insert connecting cable CL-17 AV
plug into AV output socket in camera, then make sure it insert firmly.
AV output and external shutter use the same interface for some cameras,
so you don't need this step.
3. Insert Mini USB plug of connecting cable CL-17 into Mini USB socket
of Wired live view remote control and make sure it inserts fully.
There is mis-plug interface in Mini USB plug of CL-17 cable, please note
insert direction so as to avoid damage to the Wired live view remote
control socket and cable plug.

How to use LV-122
12
11
Live View
1. Open the Live View mode on camera.
When you want to real-time monitor, you have to turn on the monitoring function(Lv)of camera.
Please read the camera instruction for turn on the live view mode, because there is difference
turn on method for each camera.
Because of some camera without real-time monitoring function, you couldn't real-time monitor
when you use this product with these cameras, you can preview the photo after shooting.
Adjust LCD brightness
After turn on the LCD, it default to be darkest brightness.
Increase brightness by pressing the button of LCD brightness
+, decrease brightness by pressing the button of LCD
brightness -. There is four step of brightness.
In some special occasion, using the wired live view remote
control along with elevating tripod, you can shoot with enviable
altitude and angle.
When use the wired live view remote control along with
elevating tripod, please make sure connecting them firmly so as
to avoid that the camera fall off from elevating tripod.
LV-122
How to use LV-122 EnEn
2. Open the display of the .Wired live view remote control
After you connect the with camera,
turn on it and open the monitoring function, at this moment please
press the screen display button of the wired live view remote
control, it will display the scene from camera.
If the camera without real-time monitoring function, the screen of
the wired live view remote control will display the preview picture
of last shooting, or the content of camera at that moment.
wired live view remote control

Shooting
14
13
By left [ ] or right [ ] movingorto set shooting mode, the shooting mode is as following:
single shooting, continuous shooting per second, [ ] shooting and delay shooting.
Single shooting
1. When the Wired live view remote control is on, by left [ ] or
right [ ] moving to make the indicator of single shooting on. At
this moment, the shutter release button has the function of
single shooting. EnEn 2. Half-press the shutter release button, the shutter indicate light
on as green color. The camera is focusing status until release or
full press the button.
3. Full press the shutter release button, the shutter indicate light
on as red color. The camera is taking picture.
Make sure set the camera function to be [ ].
When the camera function is set to be [ ], may continuous shooting.
When the camera function is set to be [ ],the camera will shoot based on[ ]
function, may cause underexposure or overexposure.
When the camera function is set to be [ ], the camera will process delay shooting.
1sec continuous shooting
1. When the is on, by left or right moving or
to make the indicator of continuous shooting per second on. At that moment the
shutter release button is in the status of continuous shooting per second.
Wired live view remote control [ ] [ ]
2. Half-press the shutter release button, the shutter indicate light on as green color.
The camera is focusing status until release or full press the button.
Shooting

16
15
Shooting
EnEn
Shooting
Make sure set the camera function to be [ ].
When the camera function is set to be [ ], may continuous shooting.
When the camera function is set to be [ ],the camera will shoot based
on [ ] function, may cause underexposure or overexposure.
When the camera function is set to be[ ], the camera will process delay
shooting.
1. When the wired live view remote control is on, by left or right
moving [ ] or [ ] to make the indicator of [ ] shooting on,
at that moment the shutter release button is in the status of
[ ]shooting.
[ ] shooting
2. Half-press the shutter release button, the shutter indicate light
on as green color. The camera is focusing status until release
or full press the button.
3. Full press the shutter release button, the shutter indicate light
on as red color. The camera is entering to [ ] mode.
4. Press the shutter release button again, stop [ ] singal, the
camera stop [ ] mode.
3. Full press then hold the shutter release button, the shutter
indicate light on red color as each second. The camera keep
shooting once as each second until fully release the shutter
button.