Planet Networking & Communication IGS-10020MT User manual

Industrial L2+ Multi-Port Full Gigabit
Managed Ethernet Switches
IGS-10020MT/IGS-10080MFT
IGS-12040MT/IGS-20040MT
Quick Installation Guide

Table of Contents
1. Package Contents...................................................................... 3
2. Requirements............................................................................ 4
3. Wiring the Power Inputs ............................................................ 5
4. Terminal Setup.......................................................................... 8
4.1 Logging on to the Console................................................... 9
 4.2 ConguringIPAddress .......................................................10
5. Starting Web Management ........................................................12
 5.1 LoggingintotheIndustrialL2+ManagedSwitch .................12
 5.2.SavingConguration ..........................................................17
6. RecoveringBacktoDefaultConguration ...................................18
7. Customer Support ....................................................................20

3
1. Package Contents
Thank you for purchasing PLANET Industrial L2+ Multi-Port Gigabit
Managed Ethernet Switches, such as IGS-10020MT, IGS-10080MFT,
IGS-12040MT and IGS-20040MT. The descriptions of these models are
as follows:
IGS-10020MT Industrial8-Port10/100/1000T+
2-Port100/1000XSFPManagedSwitch
IGS-10080MFT Industrial8-Port100/1000XSFP+
2-Port10/100/1000TManagedSwitch
IGS-12040MT Industrial8-Port10/100/1000T+
4-Port100/1000XSFPManagedSwitch
IGS-20040MT Industrial16-Port10/100/1000T+
4-Port100/1000XSFPManagedSwitch
“Industrial L2+ Managed Switch” mentioned in this Quick
InstallationGuidereferstotheabovefourmodels.
Open the box of the Industrial L2+ Managed Switch and carefully
unpackit.Theboxshouldcontainthefollowingitems:
zTheIndustrialL2+ManagedSwitchx1
zQuickInstallationGuidex1
zDIN-railKitx1
zWallMountingKitx1
zDB9 to RJ45 Interface RS232 Console Cable x 1
 (OnlyIGS-10020MTdoesn’thaveconsoleinterface.)
zDustCap(Pleaserefertothetablebelow.)
RJ45 Dust Cap SFP Dust Cap
IGS-10020MT 8 2
IGS-10080MFT 3 8
IGS-12040MT 9 4
IGS-20040MT 17 4
If any item is found missing or damaged, please contact your local
reseller for replacement.

4
2. Requirements
Workstations running Windows XP/2003/Vista/7/8/10/2008, MAC OS
X or later, Linux, UNIX, or other platforms are compatible with TCP/
IP protocols
Serial Port Connection (Terminal)
The above Workstations come with COM Port (DB9) or USB-to-
RS232 converter.
The above Workstations have been installed with terminal
emulator, such as Hyper Terminal included in Windows XP/2003,
putty or tera term.
Serial cable -- one endisattached to the RS232 serial port,while
the other end to the RJ45 console port of the Industrial L2+
ManagedSwitch.
Ethernet Port connection
Workstations are installed with Ethernet NIC (Network Interface
Card)
Network cables -- Use standard network (UTP) cables with RJ45
connectors.
The above PC is installed with Web browser and JAVA runtime
environmentplug-in.
Note
Itis recommended to use Internet Explorer 8.0 or above
toaccess the IndustrialL2+ Managed Switch. If the Web
interface of the Industrial L2+ Managed Switch is not
accessible, please turn off the anti-virus software or fire-
wallandthentryitagain.

5
3. Wiring the Power Inputs
The Upper Panel of the Industrial L2+ Managed Switch indicates a DC
inlet power socket and consists of one terminal block connector within
6 contacts. Please follow the steps below to insert the power wire.
1.Insert positive/negative DC power wires into Contacts 1 and 2 for
Power1,orContacts5and6forPower2.
IGS-10020MT: 12~48VDC,24VAC
Input
DC 12V~48V, AC 24V
V1- V1+
PWR1
V2- V2+
PWR2
Fault
Figure 3-1: IGS-10020MT Upper Panel
IGS-10080MFT:12~48VDC,24VAC
Input DC 12V~48V
V1- V1+ V2- V2+
PWR1
PWR2 Fault
1A@24V
Figure 3-2: IGS-10080MFT Upper Panel

6
IGS-12040MT: 12~72VDC,24VAC
Input DC 12-72V
AC 24V
DC1
DC2 Fault
DI 0 DI 1 DO 0DO 1
GND
GND
Figure 3-3: IGS-12040MT Upper Panel
IGS-20040MT: 9~48VDC,24VAC
Figure 3-4: IGS-20040MT Upper Panel

7
2.Tighten the wire-clamp screws for preventing the wires from loos-
ening.
123456
V1+ V1- V2+ V2-
Power 1 Power 2
Positive(+)Pin Negative(-)Pin
IGS-10020MT Pin2/6 Pin1/5
IGS-10080MFT Pin2/6 Pin1/5
IGS-12040MT Pin1/5 Pin2/6
IGS-20040MT Pin1/5 Pin2/6
Note
The wire gauge for the terminal block should be in the
range from 12 to 24AWG.

8
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a
PC or notebook computer and to RJ45 type serial (console) port of the
Industrial L2+ Managed Switch. The console port of the Industrial L2+
Managed Switch is DCE already, so that you can connect the console
portdirectlythroughPCwithouttheneedofnullmodem.
PC/Workstation
with
Terminal emulation software
RJ45 to DB9 RS232 Cable
Serial Port
IP Address:
192.168.0.100
IGS Industrial Managed Switch
Figure 4-1: Industrial L2+ Managed Switch Console Connectivity
A terminal program is required to make the software connected to the
Industrial L2+ Managed Switch. Windows' Hyper Terminal program
may be a good choice. The Hyper Terminal can be accessed from the
Start menu.
1. Click START, then Programs, Accessories and then Hyper
Terminal.
2.When the following screen appears, make sure that the COM port
shouldbeconguredas:
Baud:115200
Parity:None
Data Bits: 8
Stop Bits: 1
FlowControl:None
Figure 4-2: COM Port Conguration

9
4.1 Logging on to the Console
Once the terminal has been connected to the device, power on the
Industrial L2+ Managed Switch and the terminal will display “running
testingprocedures”.
Note
1.Therearethreeswitches (IGS-10080MFT/IGS-12040MT/
IGS-20040MT)withtheRJ45typeconsoleinterface.
2.The following console screen is based on the IGS-
10020HPT; the display of the IGS-10020HPT is the
same as that of the IGS-10080MFT/IGS-12040MT/
IGS-20040MT.
Then, the following message asks to log in user name and password
as shown in Figure 4-3. Please enter the factory default user name
"admin"andpassword“admin”.
Username:admin
Password:admin
Figure 4-3: Console Login Screen
Note
1. For security reason, please change and memorize
the new password after this first setup.
2. Only accept command in lowercase letter under
console interface.

10
4.2 ConguringIPAddress
The Industrial L2+ Managed Switch is shipped with default IP address
shown below:
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the
IndustrialL2+ManagedSwitch,pleaseusetheprocedureasfollows:
DisplayofthecurrentIPAddress
1.Atthe“#”prompt,enter “show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressshowninFigure4-4.
Figure 4-4: IP Information Screen
CongurationoftheIPAddress
3.Atthe“#” prompt,enterthe followingcommandand press<Enter>
asshowninFigure4-5.
The previous command would apply the following settings for the
IndustrialL2+ManagedSwitch.
IPAddress:192.168.1.100
Subnet Mask: 255.255.255.0
Figure 4-5: Conguring IP Address Screen

11
4.Repeatstep1tocheckiftheIPaddresshaschanged.
Storethecurrentswitchconguration
5.At the “#” prompt, enter the following command and press
<Enter>.
# copy running-cong startup-cong
Figure 4-6: Saving Current Conguration Command Screen
If the IP is successfully congured, the Industrial L2+ Managed Switch
will apply the new IP address setting immediately. You can access the
Web interface of the Industrial L2+ Managed Switch through the new
IPaddress.
Note
If you are not familiar with the console command or the
related parameter, enter “help” anytime in console to
getthehelpdescription.

12
5. Starting Web Management
The following shows how to start up the Web Management of the
Industrial L2+ Managed Switch. Note the Industrial L2+ Managed
Switch is congured through an Ethernet connection. Please make sure
the manager PC must be set to the same IP subnet address.
For example, the default IP address of the Industrial L2+ Managed
Switch is 192.168.0.100, then the manager PC should be set to
192.168.0.x (where x is a number between 1 and 254, except 100),
andthedefaultsubnetmaskis255.255.255.0.
IP Address:
192.168.0.x
IP Address:
192.168.0.100
IGS Industrial Switch
RJ45/UTP-Cable
Figure 5-1: IP Management Diagram

13
5.1 Logging in to the Industrial L2+ Managed Switch
1.Use Internet Explorer 8.0 or above for Web browser and enter IP
address http://192.168.0.100 (the factory-default IP address) to
access the Web interface.
2.When the following dialog box appears, please enter the default user
name “admin” and password “admin” (or the password you have
changedbefore)asshowninFigure5-2.
DefaultIPAddress:192.168.0.100
DefaultUserName:admin
DefaultPassword:admin
Figure 5-2: Web Login Screen
Note
The following Web screen is based on the IGS-10020MT;
the display of the IGS-10020MT is the same as that of
theIGS-10080MFT/IGS-12040MT/IGS-20040MT.

14
3.After entering the password, the main screen appears as shown in
Figure5-3.
Figure 5-3: Web Main Screen of Industrial L2+ Managed Switch
The Switch Menu on the top of the Web page lets you access all the
commands and statistics the Industrial L2+ Managed Switch provides.
The Switch Menu always contains one or more buttons, such as
“System”, “Switching”, “QoS”, “Security”, “Ring”, “ONVIF” and
“Maintenance”.
Figure 5-4: Switch Menu
Figure 5-5: Switch Menu -- System

15
Figure 5-6: Switch Menu – Switching
Figure 5-7: Switch Menu -- QoS
Figure 5-8: Switch Menu -- Maintenance

16
Figure 5-9: Switch Menu -- Security
Figure 5-10: Switch Menu – Ring
Figure 5-11: Switch Menu – ONVIF
Note
If you are not familiar with Switch functions or the
related parameter, press “Help icon” anytime on the
Webpagetogetthehelpdescription.
Now, you can use the Web management interface to continue the
Switch management or manage the Switch by console interface. Please
refertotheuser’smanualformoredetails.

17
5.2.SavingConguration
To save all applied changes and set the current conguration as
a startup conguration on the Web user interface, the startup-
congurationlewillbeloadedautomaticallyacrossasystemreboot.
1. Click the Save icon on the top Switch Menu bar.
Figure 5-12: Save Cong -- Hot Key
2. Press the “Save Conguration” button.
3. Or the other way to save the setting is to Click Maintenance, Save
Startup Cong.
Figure 5-13: Save Cong -- Maintenance

18
6.RecoveringBacktoDefaultConguration
To reset the IP address to the default IP address “192.168.0.100”
and the user password to factory default mode (default password is
admin), press the hardware-based reset button on the front panel
for about 10 seconds. After the device is rebooted, you can log in the
management Web interface within the same subnet of 192.168.0.xx
and default password. Be noted that all the previous setups will be
disappearedafterthefactorydefaultresetismade.
Mini-
GBIC
100/1000X SFP
RESET
ACT
LNK
109
P1 P2 FAULT
Ring R.O.
9
LNK/ACT1000LNK/ACT1000
10
ACTLNK
1000
Reset Button
Figure 6-1: IGS-10020MT Reset Button
Reset Button
Figure 6-2: IGS-10080MFT Reset Button

19
IGS-12040MT
7
5
3
1
RESET
8
6
4
2
ACT1000 LNK
ACT100 LNK
Reset Button
Figure 6-3: IGS-12040MT Reset Button
1
3
5
2
4
617
RESET
Console
P1 P2
Ring R.O.
FAULT
Reset Button
Figure 6-4: IGS-20040MT Reset Button

20
7. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource on PLANET web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
switch support team.
PLANETonlineFAQs:
http://www.planet.com.tw/en/support/faq
Switchsupportteammailaddress:
[email protected]
IGS-10020MT/IGS-10080MFT/IGS-12040MT/IGS-20040MTUser’sManual:
https://www.planet.com.tw/en/support/downloads?&method=keyword&
keyword=IGS&view=3#list
(Please select your switch model name from the Product Model drop-
downmenu.)
Copyright ©PLANET Technology Corp. 2018.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.