Planet Networking & Communication GS-6322 Series User manual

L3 24-Port 10/100/1000T 802.3bt + 2-Port 10GBASE-T
+ 2-Port 10G SFP+ Managed Switch with Dual Modular
Power Supply Slots
GS-6322 Switch Series
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
2.1 Power Requirements ............................................................................ 4
3. Terminal Setup ........................................................................................... 6
3.1 Logging on to Console ......................................................................... 7
 3.2 ConguringIPAddress......................................................................... 8
4. Starting Web Management .........................................................................10
 4.1 LoggingintotheManagedPoESwitch .................................................10
 4.2 SavingCongurationviaWeb ..............................................................12
5. RecoveringBacktoDefaultConguration.....................................................13
6. PowerOperationModeManagement............................................................14
7. Customer Support .....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET L3 Multiple Gigabit + 4-Port 10G Managed
Switch with dual modular power supply slots. The description of this model is
shown below:
ModelName PoEPorts 10G
RJ45
10G
SFP+ PoEBudget
GS-6322-24P4X 24-Port802.3bt 2 2 Dependedonpower
supply
“Managed PoE Switch” is used as an alternative name in this Quick Installation
Guide.
Open the box of the Managed PoE Switch and carefully unpack it. The box should
contain the following items:
zTheManagedPoESwitch
zQuickInstallationGuide
zRJ45 to RS232 Cable
zRubber Feet
zTwoRack-mountingBracketswithAttachmentScrews
zSFPDust-proofCapx2
If any of these pieces are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing material,
andusethemagaintorepacktheproductincasethereisaneedtoreturnittous
for repair.

4
2. Requirements
zWorkstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zSerial Port Connection (Terminal)
The above Workstations come with RS232 COM Port(DB9) orUSB-to-RS232
converter.
TheaboveWorkstationshavebeeninstalledwithterminal emulator, such as
HyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedPoESwitch.
zEthernet Port Connection
WorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
TheabovePCisinstalledwithWeb browser.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Managed PoE Switch. If the Web interface of the Managed PoE
Switch is not accessible, please turn off the anti-virus software or
firewallandthentryitagain.
2.1 Power Requirements
The GS-6322-24P4X is designed with two modular power supply slots. It can work
with three optional 920W/1200W/2000W AC power supplies. The nal package of
switch and power supplies will depend on your purchase. It doesn’t install a power
supply by default. Please contact your local distributor or retailer for conrming
your purchase package.
Modular Power Supply Maximum Power Output Power Connector
PWR-CRPS920 920W (100-240 VAC)
IEC C16, max. 12A
PWR-CRPS1200 1200W (220-240 VAC)
PWR-CRPS2000 2000W (220-240 VAC)

5
For compatibility with electrical voltages in most areas of the world, the Managed
PoE Switch’s modular power supply can automatically adjust line power in the
range of 100-240V AC and 50/60 Hz. However, if you’d like to have maximum
poweroutput,it’srequiredspecicpowerinput.
Plug the female C15 end of the power cord rmly into the receptacle on the rear
panel of the Managed PoE Switch and the other end of the power cord into an
electricaloutletandthepowerwillbeready.
The GS-6322-24P4X is also equipped a power eject button for safe operations and
indicationsofpowersupplies.
FAN1
Power Eject
Press for 5-10s Activated
Processing
Ready for removal
PWR2
Figure 2-1: Power eject button
Caution
To ensure system normal operation, do not remove power supply
before starting power ejection button. Please refer to user manual
forstandardoperationprocedures.

6
3. Terminal Setup
To congure the system, connect a serial cable to a RS232 COM port on a PC or
notebookcomputerandtoRJ45typeofserialportoftheManagedPoESwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 3-1: Managed PoE Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
PoESwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud:115200
zData bits: 8
zParity:None
zStop bits: 1
zFlowcontrol:None
Figure 3-2: COM Port Conguration

7
3.1 Logging on to Console
Once the terminal is connected to the device, power on the Managed PoE Switch,
and the terminal will display “running testing procedures”. Then, the following
message asks to log in user name and password. The factory default user name
andpasswordareshownasfollowsandtheloginscreeninFigure3-3appears.
Username:admin
Password:admin
Figure 3-3: Managed PoE Switch Console Login Screen
The user can now enter commands to manage the Managed PoE Switch. For a
detaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.

8
3.2 ConguringIPAddress
TheManagedPoESwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
Subnet Mask: 255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
ShowthecurrentIPAddress
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure3-4.
Figure 3-4: IP Information Screen
ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure3-5.
Switch#congure terminal
Switch(cong)#interface vlan 1
Switch(cong-if-vlan)#ip address 192.168.1.100 255.255.255.0

9
The previous command would apply the following settings for the Managed PoE
Switch.
IPAddress:192.168.1.100
Subnet Mask: 255.255.255.0
Figure 3-5: Conguring IP Address Screen
4.Repeatstep1tocheckiftheIPaddresshaschanged.
Storecurrentswitchconguration
5.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 3-6: Saving Current Conguration Command Screen
If the IP is successfully congured, the Managed PoE Switch will apply the new IP
addresssetting immediately. You canaccessthe Webinterface oftheManaged PoE
SwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

10
4. Starting Web Management
The following shows how to start up the Web Management of the Managed
PoE Switch. Note the Managed PoE Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set to the same IP subnet
address.
Forexample,thedefaultIPaddress of theManagedPoESwitchis192.168.0.100,
then the manager PC should be set to 192.168.0.x (where x is a number
between1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 4-1: IP Management Diagram
4.1 Logging in to the Managed PoE Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
https://192.168.0.100 (the factory default IP address or the one that you
havejustchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screeninFigure4-2appears.
DefaultIPAddress:192.168.0.100
DefaultUsername:admin
DefaultPassword:admin
Figure 4-2: Login Screen

11
3.Afterenteringthepassword,themainscreenappearsasFigure4-3shows.
Figure 4-3: Web Main Screen of Managed PoE Switch
4.The Switch Menu on the top of the Web page lets you access all the commands
and statistics the Industrial Managed Switch provides. The Switch Menu always
contains one or more buttons, such as “System”, “Switching”, “Routing”,
“QoS”,“Security”,“PoE”,“Ring”,“ONVIF”and“Maintenance”.
Figure 4-4: Switch Menu
Now, you can use the Web management interface to continue the Switch
management. Please refer to the user manual for more.
Note
If you are not familiar with Switch functions or the related param-
eter, press “Help icon” anytime on the Web page to get the help
description.

12
4.2 SavingCongurationviaWeb
To save all applied changes and set the current conguration as a startup
conguration, the startup-conguration le will be loaded automatically across a
system reboot.
1. Click the Save icon on the top Switch Menu bar.
2. Press the “Save Conguration” button.
3. Or the other way to save the setting is to Click Maintenance, Save Startup
Cong.

13
5.RecoveringBacktoDefaultConguration
 IP address has been changed or admin password has been
forgotten –
To reset the IP address to the default IP address “192.168.0.100” or reset the
login password to default value, press the hardware-based reset button on the
rear panel for about 10 seconds. After the device is rebooted, you can log in the
management Web interface within the same subnet of 192.168.0.xx.
PWR1
PWR2
Ring
R.O.
Reset
1
ACT1000 LNK
ACT10/100 LNK
Console
115200, N, 8, 1
Reset Button
Figure 5-1: GS-6322-24P4X Reset Button

14
6. Power Operation Mode Management
The GS-6322-24P4X is designed with two extractive modular power supply slots
to support Redundant Power Supply (RPS) mode or Extended Power Supply
(EPS) mode via software setting to handle the demands of power redundancy or
additionalpowertoPoE++portsasneeded.
zRPS (1+1) mode: Where critical services are supported by PoE application,
the secondary PSU is needed to provide backup power in the event of a power
outage.
zEPS (2+0) mode: Where more PoE budget is required to support complete
application, the secondary PSU can provide additional PoE power. The two PSUs
combinedareabletoprovideamaximumoftotalPoEpower.
Userscanchooseoneordualpowersupplieswiththeinitialinstallation.
PowerModule
OperationMode
PoEBudgetwith
One1200WPSU
PoEBudgetwith
Two1200WPSUs
Power
Redundancy
RPSmode(1+1) 1000W 1000W Yes
EPSmode(2+0) 1000W 2200W -
Exampleonpowersupply:PWR-CRPS1200
Thefactorydefaultpowercongurationsareshownasfollows.
DefaultPowerModuleOperationMode:RPS
You can use the Web management interface and then System > Power
Managementtochangethepowerconguration.

15
Figure 6-2: Power Conguration web page
Pleaserefertotheuser’smanualformore.

16
7. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resourceandUser’s ManualonPLANETWebsiterst tocheckifit couldsolveyour
issue.Ifyouneed moresupportinformation, pleasecontactPLANETswitch support
team.
PLANETonlineFAQs:
https://www.planet.com.tw/en/support/faq
Switchsupportteammailaddress:
[email protected]
GS-6322SeriesUser’sManual:
https://www.planet.com.tw/en/support/downloads?method=keyword&keyword=
GS-6322
(Please select your switch model name from the drop-down menu of Product
Model.)
Copyright © PLANET Technology Corp. 2020.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.