Planet Networking & Communication ISW-504PT User manual

Industrial 5-Port Ethernet Switch
with 4-Port PoE+
ISW-504PT/ISW-514PTF
User’s Manual

Table of Contents
1. Package Contents................................................................................. 3
2. Hardware Introduction .......................................................................... 4
2.1 Switch Front Panel......................................................................... 4
2.2 LED Indicators............................................................................... 6
2.3 Switch Upper Panel........................................................................ 7
2.4 Wiring the Power Inputs................................................................. 7
2.5 Wiring the Fault Alarm Contact ....................................................... 9
2.6 Grounding the Device................................................................... 10
3. Installation ........................................................................................ 11
3.1 DIN-rail Mounting Installation ....................................................... 11
3.2 Wall-mount Plate Mounting ........................................................... 12
3.3 Side Wall-mount Plate Mounting.................................................... 12
4. Troubleshooting.................................................................................. 13
5. Customer Support .............................................................................. 14

3
1. Package Contents
Thank you for purchasing PLANET 5-Port Industrial Ethernet Switch with 4-Port
PoE+, ISW-504PT/ISW-514PTF. The interfaces of these models are shown
below:
Model Name 10/100Mbps RJ45 Ports 100FX SFP Slots PoE+ Ports
ISW-504PT 5 - 4
ISW-514PTF 4 1 4
In the following section, the term “Industrial PoE+ Switch” means the
ISW-504PT/ISW-514PTF.
Open the box of the Industrial PoE+ Switch and carefully unpack it. The box
should contain the following items:
Industrial PoE+ Switch x 1 QR Code Sheet x 1
Let’s get started with your PLANET product
ISW-514PTF
EN Please scan the QR code to browse our online User’s Manual or Quick
Installation Guide and follow the instructions to complete the setup.
User's Manual
DE
Bitte scannen Sie den QR- Code sie werden per Browser zur
Bedienungsanleitung oder Schnellanleitung weiter geleitet. Folgen Sie den
Anweisungen um die Installation abzuschließen.
FR
Veuillez scanner le code QR pour obtenir notre Notice d’Utilisation en
ligne ou notre Guide d’Installation Rapide et suivez les instructions pour
compléter la conguration
ES
Escanee el código QR para encontrar el Manual del Usuario en línea o
la Guía de Instalación Rápida y siga las instrucciones para completar la
conguración.
IT Scansiona il codice QR per consultare online il Manuale utente o la Guida di
installazione rapida e segui le istruzioni per completare la congurazione.
PT Por favor, escaneie o QR code paranavegar no Manual do Usuário ou Guia
de Instalação Rápida. Siga as instruções para completar a conguração.
PL
Zeskanuj kod QR, aby otworzyć naszą internetową instrukcję obsługi
lub instrukcję szybkiej instalacji. Postępuj zgodnie z instrukcjami, aby
zakończyć poprawną kongurację.
RU
One word modify: Отсканируйте QR-код, чтобы просмотреть наше
онлайн-руководство пользователя или руководство по быстрой
настройке, и следуйте инструкциям для завершения настройки
RO Te rugam sa scanezi codul QR, pentru a descarca User’s Manual sau Quick
Installation Guide si a urmari instructiunile necesare in nalizarea instalarii
AR
Need more help?
PLANET online FAQs:
http://www.planet.com.tw/en/support/faq
Technical Support: [email protected]
Copyright © PLANET Technology Corp. 2023.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Part No. 2360-AH0360-000
Dust Cap x 5 Wall-mount Kit x 1
If any of these are missing or damaged, please contact your dealer
immediately.

4
2. Hardware Introduction
2.1 Switch Front Panel
P1 P2 Alarm
120W
PoE Usage
90W
60W
30W
4
5
3
2
1
LNK ACT
PoE-in-Use
ISW-504PT
10/100TX
LNK/
ACT
5
DIP
1~4
VLAN
ON
Extended
OFF
Standard
Standard
1 2 3 4 5
ONDIP
4
5
3
2
1
LNK ACT
PoE-in-Use
ISW-514PTF
P1 P2 Alarm
100FX
5
DIP
1~4
VLAN
ON
Extended
OFF
Standard
Standard
120W
PoE Usage
90W
60W
30W
1 2 3 4 5
ONDIP
Figure 2-1: ISW-504PT front panel Figure 2-2: ISW-514PTF front panel
1. Fast Ethernet TP Interfaces
10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.
2. 100BASE-FX SFP Slot (ISW-514PTF)
100BASE-FX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver
module: From 2 kilometers (multi-mode ber) to 20/40/60/120 kilometers
(single-mode ber).

5
3. DIP Switch
The Industrial PoE+ Switch provides one DIP switch for Standard, VLAN
and Extended mode selections. The detailed descriptions are shown in the
following table.
DIP Switch Mode Function
Standard
Switches 1 to 5 are o
This mode makes the Industrial PoE+ Switch operate as
a general switch and all PoE ports operate at 10/100Mbps
auto-negotiation.
VLAN
Switch 5 is on
This mode makes the Industrial PoE+ Switch operate as a
VLAN isolation switch and
1. Port 1 to 4 will isolate respectively.
2. Port 1 to 4 can only communicate with port 5.
After adjusting VLAN DIP switch, reboot
the Industrial PoE+ Switch to make the
change take effect.
Extend Any of switches 1 to 4 is on
This mode makes the Industrial PoE+ Switch operate on
a per-port basis at 10Mbps full duplex operation but can
support IEEE 802.3af PoE power output over a distance of
up to 250 meters overcoming the 100m limit on Ethernet
UTP cable.

6
2.2 LED Indicators
System
LED Color Function
P1 Green Lights: indicates power 1 has power.
P2 Green Lights: indicates power 2 has power.
Alarm Red Lights: indicates either power 1 or power 2 has no power.
30W Amber
O: indicates the PoE usage is less than 14W.
Blinks: indicates that the PoE usage is around 15W to 29W.
Lights: indicates the PoE usage is around/over 30W.
60W Amber Blinks: indicates that the PoE usage is around 45W to 59W.
Lights: indicates the PoE usage is around/over 60W.
90W Amber Blinks: indicates that the PoE usage is around 75W to 89W.
Lights: indicates the PoE usage is around/over 90W.
120W Amber
Blinks: indicates that the PoE usage is around 100W to
119W.
Lights: indicates the PoE usage is at the maximum.
Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1 to Port 4)
LED Color Function
LNK/
ACT Green
Lights: indicates the link through that port is successfully
established at 10Mbps or 100Mbps.
Blinks: indicates that the switch is actively sending or
receiving data over that port.
PoE -
in-Use Amber
Lights: indicates the port is providing DC in-line power.
O: indicates the connected device is not a PoE powered
device (PD).
Per 10/100BASE-TX Interface (Port 5 of ISW-504PT)
LED Color Function
LNK/
ACT Green
Lights: indicates the link through that port is successfully
established at 10/100Mbps.
Blinks: indicates that the switch is actively sending or
receiving data over that port.

7
Per 100FX SFP Slot (Port 5 of ISW-514PTF)
LED Color Function
LNK/
ACT Green
Lights: indicates the link through that port is successfully
established at 100Mbps.
Blinks: indicates that the switch is actively sending or
receiving data over that port.
2.3 Switch Upper Panel
The upper panel of the Industrial PoE+ Switch consists of one terminal block
connector within two DC power inputs.
Figure 2-3 shows the upper panel of the Industrial PoE+ Switch.
Max. Fault Alarm Loading: 24V, 1A
DC Input:
12-54V , 7A max.
V1+ V2+
PWR1 Alarm PWR2
1 2 3 4 5 6
Figure 2-3: Industrial PoE+ Switch Upper Pane
2.4 Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of Industrial PoE+
Switch is used for two DC redundant power inputs. Please follow the steps
below to insert the power wire.
When performing any of the procedures like inserting the wires
or tightening the wire-clamp screws, make sure the power is
OFF to prevent from getting an electric shock.

8
1. Insert positive and negative DC power wires into contacts 1 and 2 for
POWER 1, or 5 and 6 for POWER 2.
Max. Fault Alarm Loading: 24V, 1A
DC Input:
12-54V , 7A max.
V1+ V2+
PWR1 Alarm PWR2
1 2 3 4 5 6
DC Input Max. PoE Budget
12V 60W
24v 90W
48V-54V 120W
To avoid damage, please use the Industrial PoE+ Switch under
its specification.
2. Tighten the wire-clamp screws for preventing the wires from loosening.
123456
Power 1 Alarm Power 2
+ - + -
The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.

9
2.5 Wiring the Fault Alarm Contact
The fault alarm contacts are in the middle of the terminal block connector as
the picture shows below. Inserting the wires, the Industrial PoE+ Switch will
detect the fault status of the power failure and then forms an open circuit. The
following illustration shows an application example for wiring the fault alarm
contacts.
Fault Alarm Contacts
The Fault Alarm Contacts are
energized (CLOSE) for normal
operation and will OPEN when
failure occurs
Alarm
Insert the wires into the fault alarm contacts
1. The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V, max. 1A currents.

10
2.6 Grounding the Device
Users MUST complete grounding wired with the device; otherwise, a sudden
lightning could cause fatal damage to the device.
Max. Fault Alarm Loading: 24V, 1A
DC Input:
12-54V , 7A max.
V1+ V2+
PWR1 Alarm PWR2
1 2 3 4 5 6
Earth Ground
EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.