Planet HTS-1000P User manual

10-inch Touch Screen Home
Automation Controller
HTS-1000P

10-inch Touch Screen Home Automation Controller
HTS-1000P
Copyright
Copyright ©2015 by PLANET Technology Corp. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect
to the contents hereof and specifically disclaims any warranties, merchantability or fitness for
any particular purpose. Any software described in this manual is sold or licensed "as is".
Should the programs prove defective following their purchase, the buyer (and not PLANET,
its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and
any incidental or consequential damages resulting from any defect in the software. Further,
PLANET reserves the right to revise this publication and to make changes from time to time
in the contents hereof without obligation to notify any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to
computer or peripheral devices.Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency
exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches)
during normal operation.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer
manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
- 2 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result of
the presence of hazardous substances in electrical and electronic equipment, end
users of electrical and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted
municipal waste and have to collect such WEEE separately.
Revision
User’s Manual of PLANET 10-inch Touch Screen Home Automation Controller
Model: HTS-1000P
Rev: 1.00 (August, 2015)
Part No. EM-HTS-1000P_v1.0
- 3 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
- 4 -
Table of Contents
Chapter 1. Product Introduction......................................................................5
1.1 Package Contents..............................................................................5
1.2 Overview.............................................................................................5
1.3 Specifications......................................................................................8
Chapter 2. Hardware Interface......................................................................10
2.1 Physical Descriptions........................................................................10
2.2 Default Setting..................................................................................11
Chapter 3. Configuration...............................................................................12
3.1 Introduction.......................................................................................12
3.2 Network Setting ................................................................................13
3.3 Settings ............................................................................................16
3.3.1 Gateway .................................................................................16
3.3.2 Z-Wave devices......................................................................17
3.3.3 Intercom..................................................................................19
3.3.4 Control Panel..........................................................................21
3.3.5 Scene .....................................................................................23
3.3.6 Upgrading...............................................................................25
3.3.7 Janitor.....................................................................................26
3.3.8 IP Cameras.............................................................................27
3.3.9 Triggers...................................................................................31
3.3.10 Activating Code.....................................................................32
3.3.11 Location Setting....................................................................34
Appendix A: Troubleshooting & Frequently Asked Questions.......................36

10-inch Touch Screen Home Automation Controller
HTS-1000P
Chapter 1. Product Introduction
1.1 Package Contents
The package should contain the following:
zControl Pad x 1
zQuick Insrallation x 1
zWall-mounted Kit x 1
zRJ45 Cable x 1
zPower Adapter x 1
If any of the above items are missing, please contact your seller immediately.
1.2 Overview
Wall-mounted Touch Panel Makes Home System Control Easy
PLANET HTS-1000P is a 10-inch Touch Screen Home Automation Controller, which
is the command center of the Home Monitoring and Automation Systems, providing
users with quick, consistent access to every device in the connected home. A simple
user interface enables customers to easily arm and disarm their system; view status
of doors, control lights, thermostats and door locks; and see live video from cameras
in and around the home – all at the touch of a button. Quick-read information, such
as weather and time, and more, is available via on-screen widgets that are
constantly updated.
- 5 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
Keep an Eye on Home with Touch Screen
You can view cameras around your home on touch screen. Keep an eye on your
kids and pets, screen visitors at your entranceway and view activity occurring
around the interior or exterior of your home whenever and wherever you want.
Lighting Control
Users can choose the most comfortable lighting brightness with the HAC-1000
Control Gateway for the perfect atmosphere. They can also choose the right time to
turn the light on for comfort, or to warn and prevent burglars from intruding the
premises.
- 6 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
Personal Scene Mode
In the "Scene" mode you can set everything you want in every room of your home
for any activity or anything in-between from morning to night. An unlimited number of
scenes can be created and customized to your personal preferences.
Energy and Cost Saving on Every Room
You can also check the current energy consumption in your home within the
configuration interface of the HTS-1000P with the HAC-1000 Control Gateway.
Manage these energy-saving devices such as power meter switches, power
switches and dimmer switches to help you reduce energy consumption and thus
save expenses on utilities.
- 7 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
AEC (Acoustic Echo Cancellation) Technology
Acoustic Echo Cancellation (AEC) technology is adopted in PLANET’s
HDP-1100PT Door Phone and HTS-1000P Touch Screen to enable to minimize the
sound signal distortion, thus guaranteeing the best-in-class sound quality.
1.3 Specifications
Product HTS-1000P
Hardware Platform
Screen Size 10.1 inch
Brightness 250 cd/m2
Video Resolution 1024 x 600
Aspect Ratio 16:9
Touch Panel Projected capacitive (multi touch)
Audio
Audio Streaming Two-way audio
Microphone Built-in microphone and speaker input
Audio Output Acoustic Echo Cancellation
Wireless interface
Standard Compliant with IEEE 802.11b/g/n
Frequency Band 2.4G: 2.400-2.484GHz
Data Rate 802.11b: 1/2/5.5/11Mbps
802.11g: 6/9/12/24/36/48/54Mbps
802.11n: up to 150Mbps
RF Transmission Power 802.11b: 17±1dBm
802.11g: 15.5±1.5dBm
802.11n: 14.5±1.5dBm
Receive Sensitivity
802.11b (11Mbps): -91dBm
802.11g (54Mbps): -77dBm
802.11n 20M (MCS7): -70dBm
802.11n 40M (MCS7): -69dBm
Security WEP (64/128-bit)
WPA-PSK (TKIP) / WPA2-PSK (AES)
WPA (TKIP) / WPA2 (AES)
Transmission Distance Up to 180 meters in open space
Network and Configuration
Network Standard
IEEE 802.11b
IEEE 802.11g
IEEE 802.11n
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
Functions SIP intercom supported (with the HDP-1100PT Door Phone)
Home Automation integrated with the HAC-1000 Home Control
Gateway
- 8 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
- 9 -
General
Power Requirements 12V DC, 1.5A
IEEE 802.3af Class 3
Operating Temperature -10 ~ 40 degrees C
Operating Humidity 0 ~ 90% (non-condensing)
Weight 620g
Dimensions (W x D x H) 258 x 163 x 24 mm
Installation VESA-mount type
Emission CE, FCC
Connectors
10/100Mbps Ethernet, RJ45
DC power jack
Power switch button (On / Off)
Volume button (+/–)
Tab button (+/–)
Home button

10-inch Touch Screen Home Automation Controller
HTS-1000P
Chapter 2. Hardware Interface
2.1 Physical Descriptions
Dimensions (W x D x H) 258 x 163 x 24 mm
Weight 620g (gross weight)
10.1-inch Multi Touch Panel
Home
V
olume
(
+/
–
)
- 10 -
Tab
(
+/
–
)
SD/SDHC (void)
Interface Description
Volume (+/–) Press to adjust the volume.
Tab (+/–) Press to select the next (+) or previous (–) item.
Home Press to display the HTS-1000P Home Menu.
SD/SDHC Future Feature

10-inch Touch Screen Home Automation Controller
HTS-1000P
- 11 -
USB Socket
(
void
)
Power Jack
HDMI
(void) Power Switch
Micro USB
(void)
RJ45
Interface Description
Power Switch Power switch to turn on/off the HTS-1000P.
Power Jack
The input power is 12V DC.
Use the power adapter included in the package;
otherwise, it may damage the unit and result in
danger.
HDMI Future Feature
Micro USB Future Feature
USB Socket Future Feature
RJ45 (LAN Socket, PoE )
Connect to Router or Hub/Switch
It is for connection with 10BASE-T Ethernet, 100BASE-TX
or 1000BASE-T Ethernet cabling. This Ethernet port with
auto-negotiation protocol can detect or negotiate the
transmission speed of the network automatically. Please
use Cat5 cable to connect the HTS-1000P to an Ethernet
network switch or hub.
ONLY use one power source, either from DC or
from 802.3af Power over Ethernet.
2.2 Default Setting
Default DHCP Client On
Default Login User Name admin
Default Login Password admin

10-inch Touch Screen Home Automation Controller
HTS-1000P
Chapter 3. Configuration
Your control pad is ready to use in your home with door phone and control gateway. Please
take a few minutes to read through this guide to familiarize yourself with the steps required to
set up your Z-Wave network and your control pad.
This chapter provides setup details of the control pad configuration.
3.1 Introduction
Parameters Description
When you are going to leave home, you can set
this button to “AWAY”, meaning alert is enabled to
enable the control pad to send out an alarm once
triggered.
When you are going back home, you can set this
button to “AT HOME”, meaning alert is disabled to
enable the control pad to stop sending out an
alarm.
The weather icon of a location where the control
pad has been set.
- 12 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
Parameters Description
The date and temperature of a location where the
control pad has been set.
The time of a location where the control pad has
been set.
The visibility of a location where the control pad
has been set.
The humility of a location where the control pad
has been set.
The pressure of a location where the control pad
has been set.
3.2 Network Setting
This section is going to introduce how to set the networking of control pad.
First of all, connect the Ethernet cable to your control pad and the other end connect to LAN
port of your internet router.
On this main page, press
the “Settings” button for
advance settings.
The default user name
and password are both
admin.
- 13 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
Quick click 7 times in the
red box area to switch to
TCP/IP setting page.
Click “Ethernet” to “ON”
and click “Ethernet
configuration” to set
networking.
Select “Static IP” and fill
out the information of IPs
and then click “Save”.
Press the Home button
to switch to main page.
- 14 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
Now you can get the
date and weather
information of your
location.
Parameters Description
IP address This address is a unique number that identifies a computer or device
on the WAN or LAN. These numbers are usually shown in groups
separated by periods, for example, 192.168.1.166.
Netmask
Subnets allow network traffic between hosts to be separated based
on the network's configuration. In IP networking, traffic takes the form
of packets. IP subnets advance network security and performance to
some level by organizing hosts into logical groups. Subnet masks
contain four bytes and usually appear in the same "dotted decimal"
data. For example, a very common subnet mask in its binary
demonstration 11111111 11111111 11111111 00000000 will usually be
shown in the corresponding, more readable form as 255.255.255.0.
DNS address
When you send email or position a browser to an Internet domain
such as xxxxx.com, the domain name system translates the names
into IP addresses. The term refers to two things: the conventions for
naming hosts and the way the names are controlled across the
Internet.
Gateway address
A gateway is a piece of software or hardware that passes information
between networks. You'll see this term most often when you either
log in to an Internet site or when emails are transient between
different servers.
- 15 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
3.3 Settings
Here you can configure all the functions of control pad.
3.3.1 Gateway
Fill out the IP of control gateway to connect with gateway.
Click the “Gateway”
button.
Click the magnifying
glass to search the IP of
gateway.
- 16 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
- 17 -
Control pad found an IP
of gateway. Click the IP
to join.
The default gateway port
is 5000, and user name
and password are both
admin.
3.3.2 Z-Wave devices
Before configuring the “Control Panel”, we need to include Z-Wave device first, because
without Z-Wave device, we cannot select any device from the control panel. You can include
and exclude Z-Wave devices via this function.
Z-Wave devices require a separate command and physical confirmation from the device itself
(usually a button press) in order to be reset (or "excluded") and removed from a controller (HA
control gateway).
Click the “Z-Wave
devices” button to add
Z-Wave devices to
gateway.

10-inch Touch Screen Home Automation Controller
HTS-1000P
Click the “Include New
Device” button to add
Z-Wave device.
When you see the
message of “Waiting for
user action”, you can
press the match button
on Z-Wave devices.
If a device is added
successfully, it will show
the message: Command
has completed
successfully in device
No. XX.
Click the “Exclude
Device” button to
exclude Z-Wave device.
- 18 -

10-inch Touch Screen Home Automation Controller
HTS-1000P
- 19 -
When you see the
message of “Waiting for
user action”, you can
press the match button
on Z-Wave devices to
exclude device.
3.3.3 Intercom
After configuring this part, you can communicate with door phones via control pad.
Click the “Intercom”
button.
Click the three-line
button on the upper right
corner and click “Add”.
Click the magnifying
glass to search the IP of
door phone.

10-inch Touch Screen Home Automation Controller
HTS-1000P
- 20 -
Control pad found the IP
of door phone and click
the IP to join.
Name the door phone
and the account and
password of door phone
are both admin. The
default SIP ID is 2001.
Go back to the main
page and click the
“Intercom” button.
You can monitor the
entrance of your house.
Also you can click the
“Talk” button to intercom
with the guest.