Planet 802.11n Wireless ADSL 2/2+ Router ADN-4000 User manual

802.11n Wireless
ADSL 2/2+ Router
ADN-4000
Quick Installation Guide

Table of Contents
Package Contents ........................................................................... 3
Physical Details............................................................................... 4
Front Panel LEDs....................................................................... 4
Rear Panel ................................................................................ 5
Rear panel Port and Button Denition ......................................... 5
Installation Procedure...................................................................... 6
Conguration ................................................................................. 8
Preparation ............................................................................... 8
Using your Web Browser............................................................ 8
Setup Wizard ............................................................................ 9
Home Screen...........................................................................13
Further information ..................................................................14

3
Package Contents
The following items should be included:
ADN-4000 Unit x 1
Quick Installation Guide x 1
User’s Manual CD x 1
Power Adapter x 1
RJ-45 Cable x 1
RJ-11 Cable x 2
Antenna x 3
ADSL Splitter x 1
If any of the above items are damaged or missing, please contact your
dealer immediately.
l
l
l
l
l
l
l
l

4
Physical Details
Front Panel LEDs
LED Status Description
PWR ON The Router is ready.
WLAN OFF Wireless LAN is disabled
BLINKING Wireless trafc is transmitting or receiving
WPS OFF WPS function is disabled
BLINKING WPS function is enabled
ADSL ON Connected to an ADSL DSLAN successfully
BLINKING No Connection
LAN1-4
ON The LAN cable is connected to the router
OFF No Connection
Blinking Network trafc transferring or receiving through
the LAN port

5
Rear Panel
Rear panel Port and Button Denition
Port Description
Reset
● Reboot router: press the reset button for less than 5
seconds, and it will keep your original congurations.
● Load factory default setting: press the reset button
for longer than 5 seconds and the router will reset
itself to the factory default settings
(Warning! your original congurations will be replaced
with the factory default settings)
Power Power connector with 12V DC 1A.
WPS Button
Wi-Fi Protected Setup (WPS) is the simplest way to
build connection between wireless network clients and
this ADSL router. Press this button on the router and
enable WPS function of the wireless clients, the router
and clients will automatically congure the security key
and connect directly. Please note that the router will
wait for WPS requests from wireless clients in 2 minutes
after the WPS button is pressed.
LAN1-4
Router is successfully connected to a device through
the corresponding port (1, 2, 3, or 4). If the LED is
ashing, the Router is actively sending or receiving data
over that port.
ADSL
Connector
The RJ-11 connector allows data communication
between the modem and the ADSL network through a
twisted-pair phone wire.

6
Installation Procedure
1.Choose an Installation Site
Select a suitable place on the network to install the ADN-4000.
Note
For best Wireless reception and performance, the ADN-
4000 should be positioned in a central location with
minimum obstructions between the ADN-4000 and the
PCs.
Also, if using multiple Access Points, adjacent Access
Points should use different Channels.
2.Connect LAN Cables
Use standard LAN cables to connect PCs to the Switching Hub ports
on the ADN-4000. Both 10Base-T and 100Base-TX connections can
be used simultaneously.
If required, connect any port to a normal port on another Hub, using
a standard LAN cable. Any LAN port on the ADN-4000 will automati-
cally function as an “Uplink” port when required.

7
3.Connect ADSL Cable
Connect the supplied ADSL cable from to the WAN port on the ADN-
4000 (the RJ-11 connector) to the ADSL terminator provided by your
phone company.
4.Power Up
Connect the supplied power adapter to the ADN-4000. Use only the
power adapter provided. Using a different one may cause hardware
damage.
5.Check the LEDs
• The PWR LED should be ON.
• The WLAN LED should be ash, when wireless AP is ready.
• The ADSL LED should be ON if ADSL line is connected.
• For each LAN (PC) connection, one of the LAN LEDs should be ON
(provided the PC is also ON.)

8
Conguration
The ADN-4000 contains a HTTP server. This enables you to connect to
it, and congure it, using your Web Browser.
Preparation
Before attempting to congure the ADN-4000, please ensure that:
• Your PC can establish a physical connection to the ADN-4000. The PC
and the ADN-4000 must be directly connected (using the Hub ports
on the ADN-4000) or on the same LAN segment.
• The ADN-4000 must be installed and powered ON.
• If the ADN-4000's default IP Address (192.168.1.1) is already used
by another device, the other device must be turned OFF until the
ADN-4000 is allocated a new IP Address during conguration.
Using your Web Browser
1. Open web browser and type http://192.168.1.1 in the browser’s
address box. This number is the default IP address for this device.
Press Enter.

9
2. A user name and password prompt will appear. The user name and
password are both “admin”.
Setup Wizard
You can use “Setup Wizard” to setup the router as follows, and the
router will connect to the Internet via ADSL line.
Click “Quick Start” to get into the quick setup procedures.
Click “RUN WIZARD” to start up this procedure.

10
Step 1 - Click “Next” to begin these four quick steps.
Step 2 - Click “Next” to setup your new administrator’s password.