Planet WNRT-300 User manual

802.11n Wireless Portable AP/Router
WNRT-300
Quick Installation Guide

Table of Contents
1. Package Contents ................................................. 3
2. Physical Introduction ............................................. 4
3. Hardware Installation ............................................ 5
4.WebUIConguration.......................................... 10
5. Further Information: ........................................... 12

3
1.Package Contents
Thank you for choosing PLANET WNRT-300, the most
convenient portable router. Before installing the router,
please verify the contents inside the package box.
Portable Router Quick Guide CD-ROM
Power Adapter USB Cable Ethernet Cable Li-ion Battery
Note
If there is any item missed or damaged,
please contact the seller immediately.

4
2.Physical Introduction
Top Panel Description
Battery
WAN/LAN
WPS
Power
Wireless
Connection
Front Panel Description
Power Switch
WPS Button
The Switch of Router,
AP and Client Modes.
Rear Panel Description
10/100Mbps WAN/LAN Port
Reset
Power Connector
5V DC Input

5
3.Hardware Installation
Note
Before you start using the portable router,
please follow the procedures below to
install and charge the battery.
Step 1: Remove the battery cover, and insert the
attached battery into the slot. Then replace
the cover back.
Step 2: Charge the battery by the attached power
adapter and USB cable.
Step 3: The red LED will be lit up. When the
battery is fully charged, the LED will be off.
Note
If you will use the WNRT-300 powered by
AC power supply for a long time, please
remove the battery from the slot and keep
it of full power in a cool and dry place.
Please follow the instructions below to activate the
WNRT-300.
STEP 1: When the battery is put into the device, turn
on the WNRT-300.
RT/Client/AP ON/OFFWPS

6
STEP 2: The default operation mode by hardware
switch is Router Mode. Please connect the
Cable/xDSL Modem to RJ-45 port of WNRT-
300 by UTP cable.
RT/Client/AP ON/OFFWPS
STEP 3: Please follow the gure below to connect the
network devices.
Router Mode
Client
N
WNRT-300
N
Cable/xDSL
Modem
Phone Jack
RJ-45RJ-11
SSID: default
WAN
001101010

7
STEP 4: Please use your PC to site survey the wireless
signal of WNRT-300, and connect your PC
with it wirelessly.
*Default SSID: default
*Default Wireless Security: No Security
Note
1. When the WNRT-300 is at Router Mode,
the only RJ-45 port will become a WAN
port. Therefore, you have to configure
it wirelessly. However, if you need to
configure the WNRT-300 by the UTP
cable, please switch it to AP Mode first.
And the RJ-45 port will become a LAN
port to be able to connect with your
computer. The incoming configuration
of AP Mode is the same as well with it
of Router Mode.

8
Note
2. If you cannot obtain an IP address
automatically from WNRT-300, please
refer to the next two figures and follow
the procedures below to referconfigure
the network connection.
Step 1. Click “Start” button located at
lower-left corner of the screen.
Step 2. Click “Control Panel”.
Step 3. Click “Network and Internet
Connections”.
Step 4. Click “Network Connections”.
Step 5. Right-click “Wireless Network
Connection” or “Local Area
Connection”, and choose
“Properties”.
Step 6. Select “Internal Protocol
(TCP/IP)” and click “Proper-
ties” button.
Step 7. Select “Obtain an IP address
automatically” and “Obtain
DNS server address auto-
matically”, then click “OK”.
Please follow the instructions below to congure the
WNRT-300.

9

10
4.WebUIConguration
Default IP Address: 192.168.1.1
Default Username: admin
Default Password: admin
STEP 1: Open the Web browser and enter the default
IP address http://192.168.1.1
The default User name and Password are both
“admin”. Then click OK button to continue.