Planika GaLiO Fire Pit Corten User manual

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 1
INSTALLATION and USER’S MANUAL
GaLiO Fire Pit Corten
G20/G25 (Natural Gas) G30/G31 (Propane-Butane/Propane)
H1
H2
D1
D2
[mm]
320
30
350
950
Manufactured by
Planika Sp. z o.o.
Bydgoska 38
86-061 Brzoza
Poland

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 2
IT IS OBLIGATORY TO READ AND KEEP THIS INSTRUCTION MANUAL.
TABLE OF CONTENTS
1. INTRODUCTION.........................................................................................................................................................4
2. SAFETY INSTRUCTIONS..............................................................................................................................................4
2.1 Safety instruction regarding the use of the gas cylinders.................................................................................5
3. INSTALLATION...........................................................................................................................................................6
3.1. Box contents .....................................................................................................................................................6
3.2. Unboxing and installation .................................................................................................................................6
3.3. Gas cylinder montage (only LPG version) .........................................................................................................7
3.4. Installation of the gas linkage ...........................................................................................................................8
3.4.1. Natural gas connection .................................................................................................................................8
3.4.2. Connection and replacement of the gas cylinder (LPG version)...................................................................9
3.4.3. Adapter for the gas cylinder connection (LPG version) ............................Błąd! Nie zdefiniowano zakładki.
3.4.4. Regulator replacement (LPG version).........................................................................................................11
4. OPERATING INSTRUCTIONS ....................................................................................................................................13
4.1. General Notes ...............................................................................................Błąd! Nie zdefiniowano zakładki.
4.2. Setting up signal code before using the appliance for the first times............................................................13
4.3. Replacing the batteries ...................................................................................................................................14
4.3.1. Receiver.....................................................................................................Błąd! Nie zdefiniowano zakładki.
4.3.2. Hand-held transmitter ..............................................................................Błąd! Nie zdefiniowano zakładki.
4.4. Remote control .............................................................................................Błąd! Nie zdefiniowano zakładki.
4.4.1. Setting Fahrenheit or Celsius ....................................................................Błąd! Nie zdefiniowano zakładki.
4.4.2. Child Lock ..................................................................................................Błąd! Nie zdefiniowano zakładki.
4.4.3. Setting the Time........................................................................................Błąd! Nie zdefiniowano zakładki.
4.4.4. Switch on the Appliance / Igniting the Fire...............................................Błąd! Nie zdefiniowano zakładki.
4.4.5. Gradually decrease flame height ..............................................................Błąd! Nie zdefiniowano zakładki.
4.4.6. Flame height directly to minimum position..............................................Błąd! Nie zdefiniowano zakładki.
4.4.7. Gradually increase flame height ...............................................................Błąd! Nie zdefiniowano zakładki.
4.4.8. Flame height directly to maximum position.............................................Błąd! Nie zdefiniowano zakładki.
4.4.9. Stand-by mode (Pilot flame) .....................................................................Błąd! Nie zdefiniowano zakładki.
4.4.10. Turning off the device...............................................................................Błąd! Nie zdefiniowano zakładki.
4.4.11. Countdown Timer .....................................................................................Błąd! Nie zdefiniowano zakładki.
4.4.12. Automatic Turn Down To Pilot..................................................................Błąd! Nie zdefiniowano zakładki.
4.4.13. Automatic Shut Off ...................................................................................Błąd! Nie zdefiniowano zakładki.
4.5. Touchpad.........................................................................................................................................................21

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 3
5. TESTING...................................................................................................................................................................22
5.1 Checking for gas leaks.....................................................................................................................................22
5.2 Checking the flame appearance......................................................................................................................22
6. MAINTENANCE AND UPKEEP..................................................................................................................................23
6.1. Testing and cleaning .......................................................................................................................................23
7. TROUBLESHOOTING................................................................................................................................................24
8. TECHNICAL SPECIFICATION.....................................................................................................................................25
9. MANUFACTURER’S CONTACT DETAILS ...................................................................................................................25

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 4
1. INTRODUCTION
The GaLiO Fire Pit Corten fireplace is a decorative fuel-effect gas appliances destined only for outdoor use. It is
obligatory to acquaint oneself with the below installation manual and user’s manual before committing to the
installation and use of the GaLiO Fire Pit Corten fireplace. This manual is to be kept safe for the lifetime of the device.
2. SAFETY INSTRUCTIONS
•Read the instructions before using the appliance.
•Use outdoors only.
•The GaLiO Fire Pit Corten fireplace should be installed and controlled annually according to the below
installation manual as well as enforced national and local laws regarding gas safety (installation and use).
•One needs to assess whether the data on the product plaque complies with the local type of gas and pressure.
•Do not change the structure of the device or its sealed elements nor modify the default settings of the GaLiO
Fire Pit Corten fireplace.
•Do not set any additional imitation blocks nor any glowing coal fragments on the burner or in the combustion
chamber.
•A CO2 or a powder fire extinguisher needs to be placed near the device.
•During the first ignition the GaLiO Fire Pit Corten fireplace needs to be burnt on maximum level for a few hours
in order for the elements to acquire correct temperature and for the remains of paint, lacquer and lubricant
to evaporate.
•Do not move the device while it’s working.
•GaLiO Fire Pit Corten has been designed for decorative purposes. The surface of the GaLiO Fire Pit Corten
fireplace including the glass screens may get hot (up to 100 degrees Celsius) with the exception of the side
walls of the appliance and the control panel. WARNING!!! Parts of the device that are easy to reach may be
very hot. Keep children away from the device.
•Glass panels must be installed when GaLiO Fire Pit Corten is in use.
•This appliance must be kept away from flammable materials during use. Do not place any combustible
materials within a distance of 1 m of GaLiO Fire Pit Corten and 2 m over the appliance (Figure 1).
Figure 1: Minimum distance to flammable materials
•When the GaLiO Fire Pit Corten fireplace is on it’s not to be exposed to rain.
•When not being used the GaLiO Fire Pit Corten is to be protected from atmospheric conditions and the main
valve of the gas cylinder needs to be turned off.
•If the GaLiO Fire Pit Corten is not in use for a longer period of time (e.g. winter time), we advise you to store it
inside.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 5
•Corrosion of the coating of the base of GaLiO Fire Pit Corten is a natural process resulting from the
characteristics of the Corten steel which the fireplace is made of. It is an additional protective layer of the
appliance against the negative influence of unfavorable weather conditions.
•Other parts of the GaLiO Fire Pit Corten fireplace are made of stain resistant material.
•Never leave a turned on GaLiO Fire Pit Corten without supervision.
•The GaLiO Fire Pit Corten fireplace needs to be installed in a place inaccessible for children, unauthorised
persons or animals for the direct contact with the flame or hot parts of the device to be impossible.
•In case of heavy wind the GaLiO Fire Pit Corten fireplace needs to be immediately turned off and one needs to
wait until the heavy wind passes.
•In case of noticing any sort of gas leaks the fireplace as well as the main valve of the gas cylinder need to be
turned off.
•After use turn off the gas cylinder valve.
2.1 Safety instruction regarding the use of the gas cylinders.
•Use only the type of gas and pressure specified by the manufacturer.
•The gas cylinders should always be placed in a vertical position –during use and transport.
•Always store the gas cylinder in an easily accessible place to allow its immediate turn-off.
•During the installation process do not allow an open flame or any ignited object to reach the gas cylinder.
•The gas cylinder should be in a distance not shorter than 1,5 metres away from the GaLiO Fire Pit Corten
fireplace.
•Leaks should be found with the use of a cleaning liquid and water. If bubbles form on the surface that means
that a there’s an existing leak.
•Always use a pressure regulator between the gas bottle and the device. Replace the pressure regulator every
5 years. The allowed pressures are: 30mbar, 37mbar (recommended), 50 mbar. Use only regulators complying
with the European EN16129 Norm.
•Use only approved and certified gas connection linkage. Replace the linkage every 2 years.
•The elastic linkage connecting gas to the fireplace is to be led away from sharp edges and hot surfaces. Refrain
from bends and twists of the elastic connection on its full length.
•Remember that the LPG bottle should be stored in a well-ventilated place. LPG gas is heavier than air and its
accumulation near the bottom surface may generate an explosive mixture.
•The housing in which the LPG bottle is (optionally) placed needs to have an appropriate ventilation. The
housing needs to have an upper ventilation slot above the top of the bottle (of an area min 1/100 of the area
of the base of the housing) and a lower ventilation slot (of an area min 1/50 of the area of the base of the
housing).
•The gas cylinder needs to be shut if the fireplace is not being used.
•Filling the gas cylinders is to be commissioned to certified gas filling stations.
•Replacement of empty cylinders for full ones is to be conducted only in authorised locations.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 6
3. INSTALLATION
3.1. Box contents
•1x complete gas fireplace
•1x Touch panel (installed)
•1x Remote control (if delivered)
•4x AA Batteries
•2x AAA Batteries (if remote delivered)
•5x bag of decorative stones
•1x magnetic gripper
•1x 4 metre rubber gas linkage –installed (only LPG version)
•1x pressure regulator (37mbar) –installed (only LPG version)
•1x installation and user’s manual
3.2. Unboxing and installation
•The contents of the boxes need to be carefully unwrapped from the foam foil.
•Remove the bags with decorative stones from the burner reservoir and place them away from it.
•Remove the Styrofoam placed on the unit.
•Carefully lift the appliance and pull out the glass shield wrapped in cardboard from the inside of the GaLiO Fire
Pit Corten.
•Check the completeness of the elements with the contents list.
•Make sure that the device nor its elements weren’t damaged during the transportation (if they were, notify
the supplier).
•Place GaLiO Fire Pit Corten on a flat, paved surface outside of the building, preferably on the place of final
installation. Leave sufficient space on the side of the appliance where control panel is located (minimum 1 m).
•The decorative stones are to be scattered evenly around the reservoir to completely cover the burner of the
fireplace.
•WARNING!!! The stones may not cover or be placed inside the device protecting the ignition unit (Photo 1).
Photo 1

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 7
•In the case of GaLiO Fire Pit Corten powered with natural gas, to obtain the optimum image of the flame, cover
the burner with a single layer of decorative stones leaving some spaces uncovered of approximately every
2-3 cm (Photo 2).
Photo 2
•If all the points were completed according to the instruction the gas bottle can be now
connected.
3.3. Gas cylinder montage (only LPG version)
•The gas linkage attached to the device allows to place the gas bottle maximally 3 meters away from the
connected control panel, however it cannot be placed nearer to the device than 1,5 meters.
Figure 2
•The optional housing for the gas bottle cannot be airtight and has to be correctly ventilated. The housing needs
to have an upper ventilation slot above the top of the bottle (of an area min 1/100 of the area of the base of
the housing) and a lower ventilation slot (of an area min 1/50 of the area of the base of the housing). The
dimensions of the housing may vary to accommodate different types and dimensions of the gas bottles
however they also have to be sufficient for hassle-free installation of the gas bottle.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 8
Figure 3
3.4. Installation of the gas linkage
WARNING!!! The montage and service needs to be conducted by a qualified professional, a company or the gas
supplier.
Before proceeding with the connection of the gas cylinder to the fireplace all activity regarding the correct placement
and installation of the GaLiO Fire Pit Corten needs to be already performed. Place the gas linkage away from hot or
sharp edges and make sure it is not twisted.
3.4.1. Natural gas connection
First and foremost, make sure that the connecting device is designed to supply a gas suitable for the type placed in
the gas installation. All necessary information regarding the desired parameters of the gas are found on the rating
plate of the device. Before connecting the gas supply, it is necessary to blow them to remove any remaining metal
filings and other contaminants from inside. Automatic gas control system should be protected from moisture and dust.
These factors may cause irreparable damage to the individual components. The pipe supplying gas to the fireplace
should be equipped with a ball valve with a recommended diameter of 1/2 inch. The individual elements of the gas
installation cannot be sealed using Teflon tape or PTFE tape.
The gas valve on the gas pipe must be installed in accordance with applicable national regulations. Before connecting
the gas, make sure that the gas pipes and connections have no dirt. Gas connection is finished with external thread
3/8 ". Regarding gas connection, the following requirements shall apply:
• You must use the gas pipe with the correct dimensions, so there is no pressure loss.
• Ball gas valve should be installed in an easily accessible place and have the necessary CE mark.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 9
3.4.2. Connection and replacement of the gas cylinder (LPG version)
The GaLiO Fire Pit Corten is delivered together with an elastic gas linkage which, on one end is connected to the valve
of the device and on the other end to the 37mbar regulator (in the twist-on version) ready to be connected to the gas
cylinder. One needs to control the expiry date of both of the regulator as well as the gas linkage and if necessary (for
instance: broken, cut, scratched linkage) replace the components for new ones according to national standards and
norms.
The GaLiO Fire Pit Corten fireplace can use metal or steel bottles or composite bottles filled with propane-butane gas
or propane gas. This device features a twist-on regulator with current pressure of 37 mbar. It can be replaced into a
regulator with a quick-release with pressure regulator of 37 mbar.
WARNING!!! NEVER use an unstable gas connection or a regulator for other gas pressure.
Gas cylinders have two types of connectors:
•Twist-on connection: The most important thing is the black seal. Always check if the seal is present and that it
hasn’t been damaged during the gas cylinder replacement. Some connections have a knob to fasten them in
place while others require the use of a wrench. Tighten securely (left thread). Using the tool pay attention not
to fasten the connection too tightly as this may damage the seal.
•Quick-release: For this type of connection no tool is required. On/off regulation of gas connection is made
through a switch on the regulator or on a special connector. In case of using a connector with a thread
regulator of an old type put a special emphasis on checking if the connecting nut has been tightly fastened
with the help of wrench.
Gas cylinder connection
Twist-on connection
Quick-release
1. Check if the bottle valve is TURNED OFF turning
it clockwise
2. Remove the protection tip and store it for later
use.
1. Remove the protection tip. Do not use any tools,
leave the tip hanging freely.
3. Before making the connection check if the black
seal is not damaged.
2. Make sure all the taps on the gas device are
closed and if the switch in in the OFF position.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 10
4. Fit the connecting nut to the cylinder with the
use of a correct wrench or the connecting knob.
(left thread) Do not allow the gas bottle
connectors to be fastened too tightly.
3. Place the quick-release regulator on the valve
and press it down hard. If the switch is correctly
turned off you will hear a characteristic click.
5. When the gas flow is required turn the valve of
the bottle counter-clockwise.
4. To let the gas flow in turn the switch into the ON
position (or into the flame image).
•Place the gas bottle in a correct distance from the fireplace (min 1,5 metres away).
•WARNING!!!Check the gas connection for leakage. If anything suggests a leak is present (for instance a
characteristic gas smell) close the gas bottle valve and under no circumstances turn the device on before
removing the leak. (See point 5.1).
•After removing the leak one may open the gas bottle valve again.
Disconnection of the gas cylinder
Twist-on connection
Quick-release
1. Turn off the GaLiO Fire Pit Corten –put it into the OFF position. The main and pilot burner need
to be turned off.
2. Turn the bottle valve into the OFF position
(clockwise).
2. Turn the switch into the OFF position.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 11
3. NEVER DO NOT unmount the regulator (or
connecting nut) when the bottle valve is
open.
4. TAKE OFF the regulator (or the connecting
nut) with the use of a wrench or a
connecting knob.
3. Take off the quick-release regulator by
pressing the switch horizontally and
simultaneously pulling the whole regulator
upwards.
5. REPLACE the linkage closer or cap on the
empty or partially full bottle if it’s not being
used.
4. REPLACE the tightening cap on an empty or
partially full bottle if it’s not being used.
3.4.3. Regulator replacement (LPG version)
1. You always need to use a pressure regulator between the gas bottle and the device. Replace the
pressure regulator every 5 years. Allowed pressures: 30 mbar, 37 mbar (recommended), 50
mbar. Use only the redactors that comply with the EN16129 European Norm.
2. Turn off the GaLiO Fire Pit Corten –the „OFF” position. The main burner and the pilot burner
need to be turned off.
3. Disconnect the regulator from the gas bottle (description above).
4. Loosen the metal clamp with the use of
a screwdriver (philips) or a flat wrench.
5. Move the clamp away from the stub of
gas regulator.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 12
6. Take off the linkage from the stub of
regulator.
7. Attach a new linkage on the stub of
regulator.
8. Move the clamp into the stub again and
tighten it. WARNING! In the event of
visible damage on the clamp, replace it
for a new one.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 13
4. OPERATING INSTRUCTIONS
The GaLiO Fire Pit Corten fireplace has a remotely control valve with a built-in ignition for the pilot flame. The flame
height of the main burner may be appropriately regulated by remote control or Touch Panel.
Photo 3: Hand-held transmitter and Touch Panel
4.1. Setting up signal code
WARNING! You only need to set up the signal code once. It is not necessary when changing the batteries of the hand-
held transmitter or receiver. The appliance is delivered already configured and ready to work.
In case of lost or damaged of hand-held transmitter the new one has to be programmed and the receiver must first
learn the hand-held transmitter’s signal code before the first use:
•Press the “RESET” button on the receiver, and keep this pressed until 2 beeps are heard. Release the “RESET”
button after the second (somewhat longer) beep.
•Press, within 20 seconds, the „-“button (small flame) on the hand-held transmitter, until 2 short beeps are
heard. The signal code has now been set up on the receiver. If, however, a single long beep is heard, this means
that setting the signal code has failed or that the wiring has been connected incorrectly.
Photo 4: Receiver “RESET” button

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 14
4.2. Replacing the batteries
If the batteries are inserted incorrectly, the electronicsor drive may be irreparably damaged. Only replace the batteries
when the appliance has been completely switched off.
NOTE: If the appliance is equipped with a 230 VAC connection, no batteries are present in the receiver.
The batteries are placed in two containers (2 batteries in each container) located at the bottom of Galio Fire Pit Corten.
(See Figure 5).
Photo 5: Receiver batteries containers
•Unscrew the cover of the first battery container with a wide screwdriver or a coin.
Photo 6: Cover of the batteries container

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 15
•Using the magnetic gripper (delivered together with the device), remove the first battery from the container.
Photo 7: Removing the first battery using the magnetic gripper
•To remove the second battery, insert the magnetic gripper into the battery container.
Photo 8: Removing the second battery from the container

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 16
•Place the new batteries into the container. WARNING! Remember about proper polarization of the batteries.
Photo 9: Placing the battery in the container
•Screw the cover of the batteries container.
•Repeat the same procedure for changing the batteries in the second container.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 17
4.3. Remote control (if delivered)
GaLiO Fire Pit Insert can be operated by radio remote control. This comprises a hand-held transmitter and a receiver.
The receiver is part of the gas control block assembly.
•Electrical connections and batteries:
oHand-held transmitter: 2x 1.5V AAA battery
oReceiver: 4x1.5V AA battery or 6 VDC
•WARNING! Without using a mains adapter, battery replacement is recommended at the beginning of each
heating season. Old or dead batteries should be removed immediately. If left in the unit the batteries can
overheat, leak, and / or explode. Do NOT expose batteries (including during storage) to direct sunlight,
excessive heat, fire, moisture, or severe impact. Each of these conditions can cause the batteries to overheat,
leak, and / or explode. Batteries must be kept within their recommended temperature limits. Ambient battery
temperature range: 32 °F to 131 °F[0 °C to 55 °C].
•The hand-held transmitter batteries have a service life of approx. one year. We recommend you use alkaline
batteries. Rechargeable batteries are not permitted.
•To replace batteries:
oOpen the cover on the back of the remote control.
oRemove the batteries from the battery compartment.
oPlace two new 1.5V batteries (LR03 or AAA type) as indicated in the battery compartment.
oClose the cover
4.3.1. Switch the Fire ON and OFF
Before operating make sure MANUAL knob on the GV60 valve is in the ON, full counter clockwise position.
WARNING! When the pilot light is ignited, the motor turns automatically to maximum flame height. If the pilot flame
goes out for any reason, wait for 5 minutes before attempting to re-light it. If the pilot does not stay lit after several
tries, turn the main valve knob to OFF.
1. Open the valve of the gas cylinder (or gas supply
valve in the gas pipe).
2. Press button until two short beeps confirms
the start sequence has begun; release button.
3. Main gas flows once pilot ignition is confirmed.
4. Handset automatically goes into Manual Mode
after main burner ignition.
5. Press and hold button to turn OFF the fire.

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 18
•This can take few seconds to ignite to pilot flame especially when you have replaced and installed a new LPG gas
cylinder.
•If the pilot light does not ignite after 3 ignition attempts close the gas tap and warn the fitter.
•Once the pilot light is burning, the main burner must ignite within 10 seconds automatically. If this does not
happen, immediately close the gas tap and warn the fitter.
•If the main burner ignites with a pop immediately close the gas tap and warn the fitter.
•If the appliance is not to be used for some time, please close the gas supply valve in the gas pipe (or valve of the
gas cylinder).
•WARNING! If the pilot flame goes out for any reason wait for 5 minutes before attempting to re-light it.
WARNING!!!
•Under conditions of increased humidity (rain, breeze, fog, dew, etc.),
there may be some temporary problems with switching on the fireplace.
This is a normal phenomenon associated with the dampening of the
ignition element.
•Before switching on the fireplace, wait until the ignition element has dried
completely.
•You can speed up this process by blowing the pilot flame with compressed
air to remove the accumulated moisture. The properly fired pilot flame
consist of 3 smaller parts.
4.3.2. Stand-by mode (Pilot flame)
Press and hold „-“button to set appliance to
pilot flame. Pilot flame remains burning (standby
position).

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 19
4.3.3. Flame height adjustment
After ignition, the burner automatically sets the
flames to the maximum height.
•To decrease flame high, or to set
appliance to pilot flame, press
and hold „-“ button.
•To increase flame high press
and hold „+“ button.
4.3.4. Flame height directly to minimum position
Pressing the „-“ button twice automatically
decreases the flames to the LOW position
NOTE: Flame goes to high fire first before going
to low fire. Backlight must be on for low fire
double-click operation!

Copyright Planika Sp. z o.o. www.planikafires.com IG0150#05 29.06.2020 20
4.3.5. Flame height directly to maximum position
Pressing the „+“ button twice automatically
decreases the flames to the HIGH position
Press and hold „+“button to increase the flame
level and to turn on the burner from the stand-by
position.
NOTE: If you turn on the burner by pressing the
button, it must ignite within 10 seconds. If this
does not happen, immediately close the gas tap
and warn the fitter.
4.3.6. Automatic Turn Down To Pilot
3 Hour No Communication Function
The valve will turn to pilot flame if there is no communication between handset and receiver for a 3 hour period. The
fire will continue to function normally when communication is restored.
Receiver Overheating
•Powered by mains adapter: The valve turns to pilot flame if the receiver temperature is higher than 176 °F
(80 °C). If batteries are installed in the receiver in this configuration the temperature must not exceed 60 °C.
•Powered by batteries and/or connected to the V module: The valve turns to pilot position if the temperature
in the receiver is higher than 140 °F (60 °C).
NOTE: When the receiver temperature is below 140 °F (60 °C), the main burner can be turned ON manually.
4.3.7. Automatic Shut Off
Countdown Timer
At end of countdown time period, the fire shuts off. The Countdown Timer only works in Manual, Thermostatic, and
Eco Modes. Maximum countdown time is 9 hours and 50 minutes.
Low Battery Receiver
With low battery power in the receiver the system shuts off the fire completely. This will not happen if the power
supply is interrupted.