Plasma Air 600 Series Instruction manual

200012-A
Plasma Air
600 Series
www.plasma-air.com
INSTALLATION, OPERATION
& MAINTENANCE
MANUAL
REV 9/2021

200012-A
LED INDICATOR LIGHT
POWER WIRES
IONIZATION BRUSHESMOUNTING FLANGEMOUNTING HOLE
AIR FLOW
FIGURE 1
FAN
DISCHARGE
FAN INLET
IN LINE 500 mA
GLASS CARTRIDGE FUSE
CONNECT
TO POWER
FIGURE 2
PA600 SERIES
MOUNTING HOLES
INTRODUCTION
The Plasma Air 600 (PA600) Series is a needlepoint brush type ionizer
producing an equal amount of positive and negative ions. This ionization
equipment is effective in reducing harmful pathogens, pollutants and odors
by introducing positive and negative ions into the system airflow. This unit is
highly versatile as it may be installed in an air handling unit, fan coil unit,
PTAC, heat pump and even a ductless split system. The PA600 Series is self
contained in a potted enclosure which has molded flanges with mounting
holes. Models are available to accept 12V DC, 24V AC / 24V DC, 120V AC
or 208 - 240V AC without the use of an external power supply.
MECHANICAL INSTALLATION INSTRUCTIONS
GENERAL MOUNTING CRITERIA:
WARNING: Do not connect to power before mechanical
installation is complete.
1. Mount ionization unit to allow access for general maintenance. Ensure the
brush tips are not within ¾" of any metallic surface to prevent arcing.
2. Mount the unit at or near the fan inlet using the holes in the mounting
flanges, ensuring that the air stream flows over the 2 brushes
simultaneously. See figures 1 & 2.
3. For best results, the unit should be mounted downstream of the filter.
4. For best results avoid locations directly after a cooling coil or humidifier.
Note: Ionizer may be mounted
downstream of the fan if fan
inlet area is not accessible.

200012-A
ELECTRICAL INSTALLATION INSTRUCTIONS
WARNING: Do not connect to power before installation is complete.
Always disconnect power to the ionizer before handling.
1. All field wiring to be in accordance with NEC and Authorities Having
Jurisdiction (AHJ).
2. It is recommended that surge protection be installed with this ionizer at
the equipment level, building level, or circuit breaker panel feeding the
product.
3. If a step down transformer is used to feed the ionizer, the transformer
must be grounded.
4. Do not install the ionizer on the same circuit as a UV Lamp or connect to
the same transformer as a UV Lamp.
5. Connect power to the ionizer using appropriate voltage per the following:
601(12V DC) 602 (24V AC / 24V DC) 603 (120V AC) 604 (208-240V AC)
See figure 3.
6. The installer shall provide a power source that is properly grounded per
the local AHJ.
7. For best results interlock ionizer with fan power.
8. Apply power to unit. Confirm that green indicator light illuminates
indicating that the ionizer is functioning properly.
OPERATION
1. When power is supplied to the ionizer, the ionizer will be activated and
the green ion indicator LED will illuminate.
2. The ionization unit is self balancing and does not require any type of
adjustment.
TROUBLESHOOTING
If the unit is not working, check the following:
1. The supply fan is running and that the green LED illuminates.
2. Check the power input connections to the ionization unit. Verify all
connections are correct and tightened. Reconnect any loose wires as
necessary.
FIGURE 3
PA600 SERIES
IONIZER
(BLACK AC/RED DC)
(WHITE AC/BLACK DC)
FUSECONNECT
TO POWER

©2021 All rights reserved.
200012-A
www.plasma-air.com
PLASMA AIR INTERNATIONAL, INC
290 HARBOR DRIVE, FLOOR 2
STAMFORD, CT 06902
phone [phone]
fax [phone]
[e-mail]
MAINTENANCE
1. The PA600 Series was designed for low maintenance. At least every six
(6) months, inspect the ionizer brushes for dirt. If the carbon fiber
brushes do get dirty, the instructions below outline how to clean the
device:
a. Disconnect power.
b. Remove any accumulated dust on the bristles of the brushes with
either compressed air or a small brush. Avoid brushes with metal
bristles as these could damage the bristles.
c. Reconnect power.
2. Inspect the LED light for dirt which can make the light hard to see. If
dirt is present, wipe the LED with a small alcohol towelette.
SEQUENCE OF OPERATION
1. For units that are interlocked with the supply fan control, the BAS
controls the start/stop of the air conditioning unit supply fan.
European Union Importer:
Novaerus (Ireland) Limited
Old Finglas Road
Glasnevin, Dublin 11, Ireland
[phone]
www.novaerus.com