Playcore BigToys MEC104 User manual

Issued/Revised:
SHEET 1 OF 4
MEC104 WALL MOUNT MIRROR - METAL
1-866-814-8697 bigtoys.com
EC104 WALL MOUNT MIRROR - WOOD
7/25/2016
Parts List
PART NUMBER
EC104MEC104DESCRIPTION
9946M02
WINDOW FRAME - M
994620
WINDOW FRAME - W
40543511
MIRROR
40543602
PLASTIC SIDE FRAME
40543420
SIDE FRAME
E73411
G030*
66
10MM DO-NUT BASE
G032*6610MM DO-NUT CAP
815509*
2020
#10 x 1 1/2" WOOD SCREW
801013*663/8" x 3 1/2" HEX HEAD BOLT
817424*
66
3/8" FLAT WASHER (1 1/4" O.D.)
804353*663/8" LOCK NUT
---HARDWARE COMPLETE---
Items listed below Hardware Complete line are included with Hardware Complete Number
Warning: During Installation, Hardware And Small Parts Are Choking Hazards For Young Children. Store
Unused Parts Appropriately Until Assembly Is Completed. Once Assembly Is Completed, Remove Any
Unused Parts From The Play Environment And Dispose/Save Them In A Secure Location. Any bolt end
protruding more than two full threads beyond the face of the nut causes risk of clothing entanglement.
Promptly cut-off flush, file smooth, and treat to prevent corrosion.
Unless Otherwise Specified, All Units of Measure are Each
Note: Peen Tee-Nuts and Flatwashers to match radius of pipe after assembly is complete.
Note: Loctite (supplied by others) should be used on any non-patch hardware.
SPECIFICATIONS:
Window Frame and Plastic Side Frame (Metal):
Shall be fabricated from 2" x 6" plastic lumber that are made from 98% post-consumer (primarily recycled milk jugs and bleach bottles)
high-density polyethylene (HDPE). The remaining 2% is pigment and UV inhibitors. All loadbearing components are also fiberglass
reinforced for rigidity. Density/L.F.:0.061.
Window Frame and Side Frame (Wood):
Shall be fabricated from 2" x 6" Lodgepole Pine. They ar conditioned with Copper Azole - a wood preservative - after fabrication, and prior
to assembly of the wood components.
Mirror:
Shall be fabricated from 20ga. stainless steel with a type 403 bright annealed mirror finish on both sides.
INSTALLATION INSTRUCTIONS:
1. Position the Mirror against the wall and approximately 25 in. above the ground.
2. Using Mirror as a template, mark the (6) Ø 1/2" hole locations on the wall.
3. Remove the Mirror and drill (6) Ø 1/2" holes at the marked locations on the wall.
4. Attach Window Frame and Side Frame to Mirror using #10 x 1 1/2" Wood Screw. See Detail 332.
5. Attach assembled Wall Mirror to wall using 10mm Do-Nut Cap, 3/8" x 3 1/2" Hex Head Bolt, 10mm Do-Nut Base, 3/8" Flat Washer
(1 1/4" O.D.), and 3/8" Lock Nut. See Detail 367.

Issued/Revised:
SHEET 2 OF 4
MEC104 WALL MOUNT MIRROR - METAL
1-866-814-8697 bigtoys.com
EC104 WALL MOUNT MIRROR - WOOD
7/25/2016
FINISHED ASSEMBLY
MEC104 SHOWN
WINDOW FRAME - M
(9946M)
PLASTIC SIDE
FRAME (405436)
WINDOW FRAME - M
(9946M)
PLASTIC SIDE
FRAME (405436)
MIRROR
(405435)
367
332
UNDERNEATH
6. Plumb and level the entire assembly and tighten all fasteners.
7. When the structure is finished and satisfactory, eliminate sharp points and sharp edges (burring) on installed hardware such as nuts,
bolts, etc.
MAINTENANCE PROCEDURE:
Periodically check hardware for tightness, and tighten as necessary. Always check all parts for breakage or wear, and immediately
put equipment out of service until any faulty parts found are repaired or replaced. Also Check all metal parts for rust, paint loss and
touch-up if necessary with paint. Check for welded areas and verify integrity. Check periodically resilient surfacing for appropriate
depth and remove extraneous materials that could cause injury, infection, or disease. Maintain detailed installation, inspection,
maintenance, and repair records for each public-use playground equipment.

Issued/Revised:
SHEET 3 OF 4
MEC104 WALL MOUNT MIRROR - METAL
1-866-814-8697 bigtoys.com
EC104 WALL MOUNT MIRROR - WOOD
7/25/2016
25 in
[63.50 cm]
ELEVATION VIEW
MEC104 SHOWN

Issued/Revised:
SHEET 4 OF 4
MEC104 WALL MOUNT MIRROR - METAL
2
1
34
2
5
1
CM
0
INCH0
10961114815
712 13
4
365
1-866-814-8697 bigtoys.com
EC104 WALL MOUNT MIRROR - WOOD
7/25/2016
332
SIDE FRAME
#10 x 1 1/2" WOOD
SCREW (815509)
MIRROR
367
SIDE FRAME
10MM DO-NUT CAP
(G032)
3/8" x 3 1/2" HEX
HEAD BOLT (801013)
10MM DO-NUT BASE
(G030)
MIRROR
WALL
3/8" FLAT WASHER
(1 1/4" O.D.) (817424)
3/8" LOCK NUT
(804353)