Playcraft RV-21264 User manual

IMPORTANT NOTES: Read First
www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
ANGLED LANDING PAD RV
INSTALLATION INSTRUCTIONS
Rev A
2/14/2019
RV-21264
Page 1 of 4
FIGURE 1
Angled Landing Pad
Figure 1.2
Figure 1.1
See Footing Detail
(A) Use liquid thread lock (such as Loctite
®) with all threaded hardware.
Important: Liquid thread lock (prior
to curing) helps to eliminate the common problem of "thread seizure" in stainless steel hardware by serving
as a lubricant during assembly.
(B) Do not pour concrete until the equipment is completely assembled, leveled and plumbed. Concrete must
be allowed to cure completely before using the equipment (at least 72 hours).
(C) Refer to the Site Plan included with the Installation Guidelines for additional Footing Layout dimensions.
Actual hole locations may vary according to system design.
(D) An appropriate energy absorbing safety surface is required under and around all playground equipment.
Loose fill protective surfacing is shown only as an example for the purpose of this assembly instruction. Other
surfacing material may vary in thickness and/or compression depths. See free publication - The Handbook for
Public Playground Safety, Publication #325 at www.cpsc.gov for the surfacing appropriate for the fall height
of the equipment or consult your surfacing supply representative.

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
RV-21264
Page 2 of 4
Rev A
2/14/2019
ANGLED LANDING PAD RV
INSTALLATION INSTRUCTIONS
27"
686mm
*
18"
457mm
12"
305mm
LOOSE FILL SURFACING MATERIAL SHOWN:
9" compressed or 12" uncompressed depth.
Compressed depth shown. (See Note D)
(Finish Grade)
(Top of Soil)
Optional Filter Fabric over
Pea Gravel (for drainage)
Concrete Footing
Footing Anchor
Blocking, see
Installers Manual
2b Stone, drain rock
Undisturbed Soil
Elevation View
48"
1219mm
42"
1067mm
21"
533mm
Step 1
Refer to Footing Layout and mark footing hole
location(s). Dig (2) Ø 12" footing hole(s). Refer to Footing
Detail for depth and details.
IMPORTANT:
For areas with soft soil conditions, larger
footings may be required.
* Footing depth must be adjusted to compensate for the
depth/thickness requirements of selected safety
surfacing. See Section 06.1 of the Installation Manual.
Top View - Footing Layout

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
RV-21264
Page 3 of 4
Rev A
2/14/2019
ANGLED LANDING PAD RV
INSTALLATION INSTRUCTIONS
LANDING PAD
3/8" x 1-1/4"
Button Head
Bolt
3/8" x 1" O.D.
Washer
3/8" x 1" O.D.
Washer
3/8" Lock Nut
LANDING PAD
FRAME
Figure 1.1
LANDING PAD
FRAME
3/8" x 7/8" O.D.
Washer
3/8" x 1" Button
Head Bolt
Figure 1.2
Step 3
Attach Landing Pad to Landing Pad Frame as shown
in Figure 1.1. (See Note A)
Step 4
Refer to Footing Detail and remove required Hole
Plugs. Place Angled Landing Pad Frame into footing
holes and attach to post as shown in Figure 1.2.
(See Notes A & B)
Step 5
Fully tighten all fasteners according to the
"TIGHTENING TORQUE FOR HARDWARE" section
of the Installation Manual.
Step 6
Plumb and level entire component. Pour concrete
into footing hole(s). Allow at least 72 hours to cure
before using this equipment. (See Note B)
Step 7
Place required protective surfacing under and
around Angled Landing Pad. (See Note D)

www.playcraftsystems.com
For Customer Service Call
800.333.8519 (U.S.A.) or 541.955.9199 (International)
ANGLED LANDING PAD RV
INSTALLATION INSTRUCTIONS
Rev A
2/14/2019
RV-21264
Page 4 of 4
ANGLED LANDING PAD FRAME:
Shall be fabricated using 2.375" O.D. 11 gauge
steel tubing and 1.315" O.D. 12 gauge handles
with a welded 1/4" steel mounting bracket. The
Angled Landing Pad Frame shall have a multi-
stage baked-on powder coat finish.
LANDING PAD:
Shall be fabricated using punched, formed, and
welded 12 gauge sheet steel. The Landing Pad
shall be Play-Tuff™ coated after fabrication.
HARDWARE:
Shall be stainless steel, zinc/nickel plated or
galvanized as required to resist rust and
corrosion.
Part #
DESCRIPTION QTY
CE-0333 Landing Pad
1
FS-21264-RV Angled Landing Pad Frame RV
1
9103052-TR Bolt Button Head 3/8" x 1"
2
9103062-TR Bolt Button Head 3/8" x 1-1/4"
4
9333002 Washer Flat 3/8" x 1" O.D. x .100" thick
8
9333042 Washer Flat 3/8" x 7/8" O.D.
2
9413002 Nut Lock 3/8"
4
Parts List Specifications
Periodically tighten all screws, bolts and nuts. A
periodic inspection of all parts is necessary. If a part
is broken or worn, replace immediately. For general
maintenance please refer to our Playground
Maintenance Manual.
Maintenance