Plinth 2000 113B User manual

Phlebotomy Chair
Model: 113B
SERVICE MANUAL

Phlebotomy Chair Service Manual
2 | Page
Contents
1. Introduction 3
General Warnings 3
2. Cleaning and Decontamination 4
3. Maintenance 5
General maintenance 5
Service checklist 6
4. Troubleshooting 7
5. Parts Lists and Diagrams 8
Exploded Diagram 9
Back-Rest Drawing 10
Foot-Rest Drawing 11
Blood Arm Drawing 12
6. Guarantee 13
7. Technical Specification 14
8. Revisions to Manual 15
Plinth 2000 Ltd is an ISO Audited company to ISO9001:2008
Our products are CE marked in conformity with the EC Directive MDD 93/42/EEC

Phlebotomy Chair Service Manual
3 | Page
1. Introduction
Thank you for purchasing a product from Plinth 2000 Ltd. We use the highest quality
components and manufacturing techniques to ensure that our products are simple
to use and will last a long time. It is recommended that all users read and retain this
User Manual for reference.
Throughout this manual notice is made of a Warning and Caution system to highlight
to the user practices, procedures or conditions that should either not be allowed to
happen or happen with caution.
Warnings are in a box with bold type and identify potential hazards, procedures or
conditions which could result in death, injury or serious damage.
Cautions are in a box with plain type and identify conditions or procedures where if
caution is not taken it may result in damage or failure of equipment.
General Warnings
WARNING
Maximum Load (SWL) is 250kg distributed evenly.
Do not concentrate weight on either side or either end of the chair.
Use only accessories approved for use with this chair.
Children must be adequately supervised in the presence of the chair.
Do not allow children to play with the chair at any time.

Phlebotomy Chair Service Manual
4 | Page
2. Cleaning and Decontamination
WARNING
If contamination is suspected then decontaminate the chair before use.
Torn or damaged upholstery should be replaced immediately.
CAUTION
Do not use Alkalis or other organic solvents for routine cleaning.
Always cover the vinyl with paper towelling or couch covers if it can come into
contact with bare skin.
Cleaning
Always wear suitable protective clothing before carrying out this procedure.
Disconnect the mains supply to the chair and move it to a suitable cleaning area and
lock the castors.
Step 1. Using warm water and soap on a damp cloth, carefully wipe the chair over
from top to bottom. Take great care around electrical components.
Step 2.Wipe the chair carefully from top to bottom using a clean damp cloth and
soap free water.
Step 3. Carefully dry the chair from top to bottom with clean lint free paper towels.
Decontamination
To decontaminate the chair repeat the above steps but using a dilute solution of
Hypochlorite and warm water (10,000ppm) instead of warm water and soap. At the
end of the procedure discard all cleaning materials in a safe manner and wash hands
thoroughly.

Phlebotomy Chair Service Manual
5 | Page
3. Maintenance
Plinth 2000 Ltd products are designed to be maintenance free. However keeping
your Plinth products clean and regularly checked will assist in prolonging their
working life. The following is a guide of simple checks that the user can carry out on
a six monthly basis. We would also recommend an annual service visit by a Plinth
2000 trained engineer.
Examine the chair for any signs of damage. Pay particular attention to all nuts, bolts
and fasteners to check they are present and tight but not over tight.
Upholstery bolts should all be checked (each section has between 2 and 6 No. M6
bolts), they should all be present and tight.
Check gas struts (if fitted) and ensure that they operate through the full range of
movement and lock fully.
Check hinge pins are lubricated and not rusty.

Phlebotomy Chair Service Manual
6 | Page

Phlebotomy Chair Service Manual
7 | Page
4. Troubleshooting
In the unlikely event of the chair failing to operate and having carried out the normal
practical fault finding steps below then please contact our Customer Service Team
on [phone] or email [e-mail]. Please have the
serial number to hand before making contact so we can help you more efficiently.
Fault
Possible Cause
Remedy
Chair is unstable
Uneven floor
Fixed foot not adjusted
Move chair to flat floor
Check presence, condition
and adjustment of all four
feet
Backrest or footrest will
not work (manual
versions)
Gas spring incorrectly
adjusted (not being
triggered)
Gas spring faulty
Rotate gas spring until the
pin is just in contact with the
lever (2-3mm play required)
Replace gas spring
Backrest or footrest
sinks under load
(manual versions)
Gas spring incorrectly
adjusted (permanently
triggered)
Rotate gas spring until the
pin is just in contact with the
lever (2-3mm play required)
Armrests slip or are
loose
Locking thumbwheels not
correctly tightened
Thumbwheels damaged from
over tightening
Correctly tighten locking
thumbwheels
Replace thumbwheels

Phlebotomy Chair Service Manual
8 | Page
5. Parts Lists and Diagrams

Phlebotomy Chair Service Manual
9 | Page

Phlebotomy Chair Service Manual
10 | Page