Plymold JUPITER User manual

PAGE 1
INSTALLATION INSTRUCTION
PRODUCT: JUPITER CLUSTER FRAMES
MANUAL: Z000000071
ATTENTION INSTALLERS: PLEASE PRESENT INSTALLATION DOCUMENTS TO FACILITIES MANAGER.
American Filing Solutions
P.O. Box 891719, Temecula CA 92589
Tel: [phone] or 1-888-891-1970
Fax: [phone] or 1-888-891-9970
Email: [email protected]
www.FilingToday.com

INSTALLATION MANUAL
PAGE 2
COMPONENT INDEX FOR ASSEMBLY
UNPACKING YOUR SHIPMENT
Unpack and identify each component in each box that you received. If your shipment is missing parts,
or too many parts were shipped, please contact Plymold Seating. Phone [phone]
COMPONENTS:
SCREW GUN W#2 PHILLIPS BIT
SCREW DRIVER
TAPE MEASURE
PENCIL OR MARKER
WRENCH SET
7/16” SOCKET AND OPEN END WRENCH
#10X1.00”
TOOLS REQUIRED:
JUPITER TWO SEAT FRAME
1/4-20 NUT
FLOOR ANCHOR 1/4-20 X 5/8”
BOLT
ADJUSTABLE
GLIDE
EXPANSION
SPACER
JUPITER FOUR, SIX, AND
EIGHT SEAT FRAME
JUPITER ADA FRAME
SIX SEAT
SPIDER

INSTALLATION MANUAL
PAGE 3
STEP 1: GLIDE ASSEMBLY
1. Screw the thread in glide into the insert in each of
the four (4) legs.
fig. 2
fig. 1
STEP 2: ASSEMBLING TWO AND FOUR FRAME
1. Align holes in table angles. (fig.1)
2. Fasten the two frame halves together using 1/4”-20 bolts and nuts.
Note: Hand tighten nuts and bolts.
3. Level table angles. (fig.2)
4. Tighten nuts and bolts using a wrench.
Note: If the table tops are wider than 24” a expansion spacer is
reqiured. (fig. 3)
fig. 3
STEP #3 ASSEMBLE SIX SEAT FRAME
1. Align holes in table angle with holes in spider. (fig.1)
2. Fasten the frames and spider together using 1/4”-20 bolts and nuts.
Note: Hand tighten nuts and bolts.
3. Level table angles.
4. Tighten nuts and bolts using a wrench.
fig. 1
fig. 2 fig. 3
Mounting Holes
Expansion Spacer

INSTALLATION MANUAL
PAGE 4
STEP #4 INSTALLING TABLE TOP
1. Place table top on frame and center.
2. Secure table top from moving while fastening using six (16) #10 x 1.00”
screws.
CENTER
STEP #6 FASTENING GLIDES TO FLOOR
1. Rotate glides so that the mounting hole is pointing towards the center of
the booth.
2. With a pencil, mark the hole location on the floor using the holes in the
glide.
3. Turn the glide away 90 degrees from its current position to expose the
mark on the floor.
4. Using a hammer drill and a 1/4” masonary bit, drill a 1 1/4” deep hole on
the pencil mark.
5. Place a plastic anchor in the hole and then rotate glide back so its hole
lines up with thr plastic anchor in the floor.
6. Insert a #10 x 1.00” screw through the hole in the glide and secure into the
plastic anchor.
NOTE: Frames must be anchored to the floor to maintain stability and
prevent personal injury.
Floor Fastening
CENTER
STEP #5 POSITIONING AND LEVELING BOOTHS
1. Confirm location of booths with floor plan.
2. Level booths by adjusting thread-in glides.
BOTTOM VIEW OF UNITS
CENTER TOP

INSTALLATION MANUAL
PAGE 5
STEP #7: FASTENING CHAIRHEADS TO FRAME
1. Place chairhead onto frame by locating the four studs on the chairhead and
inserting the studs into the the holes on the plates.
2. Secure the chairhead to the frame usong 1/4”-20 nyloc nuts.
3. Tighten chairhead using a 7/16” wrench.
STEP #8: CARE
1. Clean furniture and protect unit ready for use.