Plymold Contour User manual

Contour
Revised01/30/2017
Z000000201
WallStyleAdjustable

ContourPage2of9
UnpackingYourShipment
Unpackandidenfyeachcomponentineachboxthatyoureceived.Ifyourshipmentismissingparts,ortoomany
partswereshipped,pleasecontactPlymold.
Components
CapScrewBuonHead
3/8‐16x3‐1/2”
(ADAFRAMEONLY)
WALLSTYLEADAFRAME
ADJUSTABLEWALLSTYLEFRAMECONTOURSEATTABLETOP
REARSEATHOOKFRONTSEATHOOK1/4—20ELBOWBOLTKEPNUT1/4‐20
SINGLESEATHARDWARE
ADJUSTABLEPLASTIC
GLIDE(A)
PLASTECFLOORANCHORSCREW#10X1”
FLOORANDTABLEHARDWARE
HEXHEADCAPSCREW3/8‐
16x33/4”
MACHINESCREW
1/4‐20x5/8”
WASHER3/8”
HEXHEADCAPSCREW1/4‐
20x3/4”
NylonInsertLock
Nut3/8‐16
FRAMEHARDWARE
OTHERHARDWARE
TEKSCREW#10x1”
P85683KDHARWAREKITINCLUDESHARDWAREBELOW

ContourPage3of9
ToolsRequired
Assembly















ScrewGunw/#2PHILLIPSBit PencilorMarker  HammerDrill  4”Bit 



ScrewDriverRatchet,5/16”,7/16”&9/16”SocketandOpenEndWrench Level  TapeMeasure

AdjustableWallStyleFrame‐BeginonPage4

ADAAdjustableWallStyleFrame‐BeginonPage5

ContourPage4of9
Assembly
Step2:FrameAssembly
a.Using3/8”‐16x33/4”hexheadcapscrew,3/8‐16lock
nutand3/8”washers,assembletheseatsupportlegto
themainsupportframe.
Note:Centerholesarefor24”widetopspacing.






b.Repeatstepawiththesecondseatsupportleg.







c.Aachthecanlevertothemainsupportframeusing
1/4‐20x5/8”machinescrewsonthe
boom.Usethe1/4‐20x3/4”hexheadcapscrews
witha1/4‐20kepnutonthetop.



ConnueonPage6
Step1:GlideAssembly‐AdjustableWallStyleFrame
a.Assembleathread‐inglideintotheinsert
ineachofthefour(4)legs.
(A)
(A)

ContourPage5of9
Assembly
(A)
(A)
(A)
(A)
(A)
Step2:FrameAssembly
a.Using3/8”‐16x33/4”hexheadcapscrew,
3/8‐16LockNutand3/8”washers,assem‐
bletheseatsupportlegtothemainsup‐
portframe.
Note:Useoutsideholes,noadjustment.






b.Aachsupportlegusing3/8‐16x3‐1/2”
capscrewbuonheadand3/4‐16lock
nuts.
Note:Placebuonheadoninsideofleg.




c.Aachtableangletomainsupportusing
1/4‐20x2.0”hexheadscrewsand1/4‐20kep
nut.Aachcanlevertomainsupportusing1/4‐
20x5/8”machinescrewsontheboomand1/4
‐20x3/4”hexheadcapscrewswitha1/4‐20
kepnutonthetop.

Step1:GlideAssembly‐ADAWallStyleFrame
a.Assembleathread‐inglideintotheinsert
ineachofthefour(6)legs.


Contour
Step3:AssembleSeattoFrame
a.Locatesingleseathardwarekit.
b.Posionseatonendandinsertfronthooks.



c.Posiontheseatovertheframebyppingtheedgeoftheseatforwardandpullingtheseatinto
place.



d.Aachelbowboltstofrontseathooksandhandghten
1/4‐20kepnut.



e.Insertshorttongueofrearseathookintotheseatplate.Usingaflatheadscrewdriverpryrearseat
hookunlitpopsintoplace.






Assembly
Page6of9
f.Nowthattheseatisinstalled,insertaself‐drilling
screwintotheholeintherearseathook.Onescrew
foreachrearseathook.Donotoverghten.

Contour
Step4:InstallingTableTop

a.Placethetabletoponthecanleverframe.
b.Posiontableperdrawingsbelow.
c.Securethetabletopfrommovingwhilefastening,using(6)#10x1.0”screws.





Assembly
Page7of9
CENTER
1.0”
2.0”
WallStyleAdjustableFrame
WallStyleADAFrame
1.0”
2.0”
2.0”
11.0”

Contour
Step5:InstallingVercalTableLeg

a.Assembleaplascthread‐inglideintoinsertifnotalreadydone.
b.Posiontableperdrawingsabove.
c.Securethetabletopusing(6)#10x1.0”screws.
Note:VercalTablelegrequiredontopslongerthan48”andADAtops.


Step6:PosionandLevelBooth

a.Confirmlocaonofbooth/frameswiththefloorplan.
b.Levelboothbyadjusngglides.



Step7:FastenGlidestoFloor

a.Rotateglidestopointthemounngholetowardsthecenterofthe
booth.
b.Withapencil,marktheholelocaononthefloorusingtheholesin
theglide.
c.Turntheglideaway90degreesfromitscurrentposiontoexposethe
markonthefloor.
d.Usingahammerdrillanda1/4”masonrybit,drilla11/4”deephole
onthepencilmark.
e.Placeaplascanchorintheholeandthenrotateglidebacksotheholelinesupwiththeplascan‐
chorinthefloor.
f.Inserta#10x1.0”screwthroughtheholeintheglideandsecureintotheplasc
anchor.

Note:Framesmustbeanchoredtothefloortomaintainstabilityandprevent
personalinjury.


Assembly
Page8of9

Contour
Step8:Care.
a.Cleanfurnitureandprotectunitunlreadyforuse.
















WallStyleAdjustableFrameContourBooth


















ADAWallStyleAdjustableFrameContourBooth
Assembly
Page8of9