PNI CA500LR User manual

Remote Controlled Relay PNI CA500LR
for controlling 1 or 2 garage doors, gates, bariers
7HFKQLFDOVSHFLILFDWLRQV:
zSensitivity: -105dBm
zCommunication frequency: 433MHz
zTransmission power; 0.1W
zPower supply: DC 12V ≤10mA
zChannels: 2
zNO/NC (Normal Open/Normal Close) command no voltage, 10A max.
zWorking modes:relay NO/NC manual, self-closing, dual
zOperating temperature: -26 ~ +60℃
zCompatible with the remote controls: PT2262, SC2260, EV1527
1.0DQXDOPRGH - press A or B on the remote; the relay closes and remains closed untill you
press the button again (doors work individually) Used to turn ON and OFF a lightbulb for example.
2. 6HOIFORVLQJ - press and hold A or B to open the door/lock/gate, when you release the button
the relay returns to its initial state ( doors work individually). Used for magnetic locks, gates etc.
3.'XDOPRGH - this mode can be used only if you connected 2 different doors (A and B) to the
relays: press button A to open door A, when you press button Bdoor A will close and door B will
open and stay open untill you open door A or power is cut off.
In this mode the relays/doors are dependent on each other.
6HOHFWLQJZRUNLQJPRGH:
Ÿcut off the power to the relay;
Ÿplace the jumper in corresponding position for the desired working mode;
Ÿconnect back the power.
/HDUQLQJWKHUHPRWH: short press learning button. The LED will lit. Press button A
on the remote. The LED will blink red 3 times then stays lit to confirm learning of the button A for
commanding the first relay. LED stays lit. Press button B on the remote. The LED-ul will blink 3
times then it turns off to confirm learning.
Repeat procedure to learn secondary remotes.
(UDVLQJWKHUHPRWHV: press and hold the learning button untill the LED turns off.
Release the button. The LED will blink 3 times to confirm erasing.
2YHUYLHZ:
GND
+12V
NC1: GND ON/OFF
COM1: +12V VDD/AC
NO1: GND VSS AC/N
Learning button Status LED
Selection jumper
working mode
manual mode dual mode
self-closing
mode
NC1 GND ON/OFF
COM1: +12V VDD/AC
NO1: GND VSS AC/N
:RUNLQJPRGHV:
Button A
relay 1
Button B
relay 2
LED indicator
1 2 3

Releu cu telecomanda PNI CA500LR
pentru comanda 1 sau 2 usi de garaj, porti, bariere
Specificatii tehnice:
zSensibilitate: -105dBm
zFrecventa comunicare cu telecomanda: 433MHz
zPutere de emisie: 0.1W
zAlimentare: DC 12V ≤10mA
zCanale: 2
zComanda tip NO/NC (Normal inchis/Normal deschis) fara tensiune cu releu maxim 10A
zMod de functionare: manual, cu autoinchidere si dual
zTemperatura de functionare: -26 ~ +60℃
zCompatibil cu telecomenzi cu chipset: PT2262, SC2260, EV1527
1. Mod manual - apasati butonul A sau B de pe telecomanda; releul declansat ramane deschis/
inchis pana cand apasati butonul din nou. Util pentru aprinderea/stingerea unui bec, de exemplu.
2. Mod cu autoinchidere - tineti apasat butonul A sau B pentru a deschide usa/yala/poarta, cand
ridicati mana de pe buton releul revine in starea initiala (usile functioneaza independent). Util
pentru comanda yale electromagnetice, porti, usi garaj.
3. Mod dual - acest mod poate fi utilizat doar daca ati conectat 2 usi diferite (A si B) la releele
disponibile si functioneaza astfel: apasati butonul A pentru a deschide usa A, cand apasati butonul B
usa A se va inchide iar usa B se va deschide si va ramane deschisa pana cand deschideti usa A
sau se ia tensiunea. In acest mod releele / usile sunt dependente una e alta.
Selectare mod functionare:
Ÿopriti alimentarea dispozitivului
Ÿplasati jumper-ul in pozitia corespunzatoare modului de functionare dorit;
Ÿrealimentati dispozitivul.
Invatarea unei telecomenzi: apasati scurt butonul de invatare. LED-ul se aprinde. Apasati
butonul A de pe telecomanda. LED-ul rosu clipeste de 3 ori apoi ramane aprins pentru a confirma
invatarea butonului A pentru comanda primului releu. LED-ul rosu ramane aprins. Apasati butonul
B de pe telecomanda. LED-ul rosu clipeste de 3 ori apoi se stinge pentru a confirma invatarea.
Repetati procedura pentru invatarea de telecomenzi suplimentare.
Stergerea telecomenzilor: apasati butonul de invatare pana cand LED-ul se stinge.
Eliberati butonul. LED-ul va clipi de 3 ori pentru a confirma operatiunea.
Descriere:
GND
+12V
NC1: GND ON/OFF
COM1: +12V VDD/AC
NO1: GND VSS AC/N
Buton invatare LED stare
Jumper selectare
mod functionare
mod manual mod dual
mod
autoinchidere
NC1 GND ON/OFF
COM1: +12V VDD/AC
NO1: GND VSS AC/N
Moduri de functionare:
Buton A
releu 1
Buton B
releu 2
LED indicator
1 2 3

EN:
EU Simplified Declaration of Conformity
SC ONLINESHOP SRL declares that Remote controlled relay PNI CA500LR complies
with the Directive RED 2014/53/UE. The full text of the EU declaration of conformity
is available at the following Internet address:
https://www.mypni.eu/products/8325/download/certifications
RO:
Declaratie UE de conformitate simplificata
SC ONLINESHOP SRL declara ca Releu cu telecomanda PNI CA500LR este in
conformitate cu Directiva RED 2014/53/UE. Textul integral al declaratiei UE de conformitate
este disponibil la urmatoarea adresa de internet:
https://www.mypni.eu/products/8325/download/certifications