PoeWit WAP-2E User manual

poewit.com
CLOUD-INTELLIGENT, ENTERPRISE-CLASS
WIRELESS ACCESS
POINTS
QUICK START GUIDE
WAP-1 / WAP-2 / WAP-2E / WAP-2O

poewit.com
INSTALLATION AND SETUP
1
WARNING: BEFORE PROCEEDING, EXAMINE AP MOUNTING TO ENSURE
THERE IS AN AIR GAP BETWEEN THE BACK OF THE AP HOUSING AND THE
MOUNTING SURFACE. AIR FLOW IS IMPORTANT TO MAINTAINING A LOW
TEMPERATURE.
1) After mounting the AP, connect an Ethernet cable (Cat 5/6) from the LAN1
port to the required PoE Switch.
• IMPORTANT: To achieve full power and wireless transmission:
• Power the WAP-2 and WAP-2E with 802.3at (PoE+)
• Power the WAP-1 and WAP-2O with 802.3bt (PoE++)
2) Once the AP is receiving power, it will automatically connect to the
internet, and its LAN1 LED will appear as follows:
• WAP-1:
• Blue LAN1 LED:
- Solid: Good link @ 2.5Gbps
- Blinking: Receiving/Transmitting @ 2.5Gbps
• Amber LAN1 LED:
- Solid: Good link @ 100/1000Mbps
- Blinking: Receiving/Transmitting @ 100/1000Mbps
• WAP-2:
• Green LED:
- Solid: LAN1 enabled

poewit.com
INSTALLATION AND SETUP
2
- Blinking: LAN1 Receiving/Transmitting
• Blue LED:
- Solid: WLAN enabled
- Blinking: WLAN Receiving/Transmitting
• Green/Blue Alt. LED: LAN1 and WLAN Receiving/Transmitting
• WAP-2E:
• Green LAN1 LED:
- Solid: Good link @ 2.5Gbps
- Blinking: Receiving/Transmitting @ 2.5Gbps
• Amber LAN1 LED:
- Solid: Good link @ 100/1000Mbps
- Blinking: Receiving/Transmitting @ 100/1000Mbps
• WAP-2O:
• Blue LAN1 LED
- Solid: LAN1 enabled
- Blinking: LAN1 Receiving/Transmitting
• NOTE: Full scope of LED definitions can be found on the product
Data Sheet.

poewit.com
INSTALLATION AND SETUP
3
3) To configure the device, download the PoEWit App from Google Play or
the Apple App Store.
• NOTE: The AP and the mobile device running the PoEWit
App must be on the same external IP address and the same
local subnet.
4) There are two configuration scenarios depending on whether or not there
is a wireless network already installed.
4a) With an Existing AP on the Network:
1. Connect to the existing AP using your mobile device.
2. Open the PoEWit App to discover and configure the new AP.

poewit.com
INSTALLATION AND SETUP
4
SSID
poewit_2.4G_1
poewit_5.0G_1
poewitguest_2.4G
poewitguest_5.0G
Passcode
3301Andrews
3301Andrews
WelcomeGuest
WelcomeGuest
4b) With No Existing AP on the Network:
1. Connect to the newly-installed AP using the default SSID and Passcode.
2. Open the PoEWit App to discover and configure the new AP.
3. Once the settings are saved, the AP will reboot and lose
connection to the mobile device. Allow 30 to 60 seconds for the
AP to reestablish power.
4. Once power is restored, connect to the new SSID you setup.

poewit.com
INSTALLATION AND SETUP
5
PoEWit Technologies Inc. All Rights Reserved 2023.