Pointman NR Series User manual
3. Pull the cartridge out while pressing the Cartridge Load/Eject Button to
remove it from the Retransfer.
4. Load the film core by pushing it vertically from top to bottom as
shown.
22 ©2020 TIT ENG Co., Ltd. All rights reserved
5. After standing up the film cartridge as below the image, turn the
black film core clockwise and pass it under the cartridge.
RFID Tag
23
POINTMAN NR Serise User Guide Manual
RFID Tag
-If the film is loose before inserting the
cartridge into the body, it will be caught
in the cartridge slot and cannot be installed.
Caution
7. Turn the edge of the film core clockwise to tighten the film as
shown in the image below.
6. Lay the cartridge again, then load the black film core by pushing it
vertically from top to bottom as shown in the image below.
24 ©2020 TIT ENG Co., Ltd. All rights reserved
25
8. Check the position of the Film Cartridge and push the cartridge in
until it clicks.
POINTMAN NR Serise User Guide Manual
Click
Load Ribbon into Ribbon Cartridge
1. Pull the cartridge out while pressing the Cartridge Load/Eject Button to
remove it from the Retransfer as shown in the image below.
RFID Tag
26
2. Load the ribbon core by pushing it vertically from top to bottom as shown
in the image below.
RFID Tag
©2020 TIT ENG Co., Ltd. All rights reserved
27
3. Put on the ribbon cartridge as below image, and then turn the recovery
ribbon core counterclockwise and pass it under the cartridge.
POINTMAN NR Serise User Guide Manual
28
4. Lay the cartridge again as image below, and then insert the recovery
ribbon core by pushing it in the direction of 45 degrees.
©2020 TIT ENG Co., Ltd. All rights reserved
- If the ribbon is stretched before inserting
the cartridge into the printer, it might be
jammed in the cartridge slot and cannot be
installed.
Caution
29
5. Turn the cartridge handle counterclockwise as image below to tighten
the ribbon.
6. Check the position of the ribbon cartridge as image below and push in
the cartridge in the direction of the arrow until it clicks.
POINTMAN NR Serise User Guide Manual
Close the front cover
1. Close the front cover by pushing it forward until it ‘clicks’.
Click
How to attach and detach the Stacker
- Do not use force to close the front cover without properly installing the cartridge.
It may cause damage to the product
-If the front cover of the printer is not closed properly, it may cause poor printing
quality. (Check the closed state)
Caution
30 ©2020 TIT ENG Co., Ltd. All rights reserved
How to attach and detach the Stacker
Insert the ‘ㄱ’ hook of the
stacker into the groove
on the product, and then
lower it to install.
(Up to 150 cards can be
stacked.)
-Attaching the stacker to the printer
Connecting power and
communication cable
Power Adaptor
Power Cable
USB Cable
Connect the power and USB communication cable to the backside of the
printer as below image.
31
POINTMAN NR Serise User Guide Manual
Supply power to the printer
Turn on the printer by pressing the power switch.
Setting after installing the
Film/Ribbon
When the initial screen is displayed after
booting, proceed to film and ribbon
setting.
100% 100%
Menu Cleaning
Eject
154℃
100% 100%
Menu Cleaning
Eject
154℃
32 ©2020 TIT ENG Co., Ltd. All rights reserved
100% 100%
Menu Cleaning
Eject
154℃
-Position the Film and Ribbon
Function : When the film and ribbon are newly loaded, press the
Sync button to adjust the position
1. Press the button to enter the film setting menu.
90%
Film Status
Film Type Number of Film Sets
Film Lot Number
Home Film sync
600Clear Transfer Flim
66200XXX
100% 100%
Menu Cleaning
Eject
154℃
2. After checking the basic information on the film press the
button to adjust the position of the film Once the printer has positioned
the film Press the button to move to the standby screen.
100%
100%
Home
Film sync
3. Press the button to enter the ribbon settings menu.
33
POINTMAN NR Serise User Guide Manual
4. After checking the basic information on the film, press the
button to adjust the position of the ribbon When the printer is in
position of the ribbon, press the button to move to the standby screen
90%
Ribbon Status
Ribbon Type Number of Ribbon Sets
Ribbon Lot Number
Home Ribbon sync
600YMCK
66200XXX
100% 100%
Menu Cleaning
Eject
154℃
Ribbon sync
Home
34 ©2020 TIT ENG Co., Ltd. All rights reserved
1. Hold the side of the stacker and pull it in the direction of the ‘ㄱ’ as below
image to detach the stacker.
-How to remove a card with the stacker detached
100% 100%
Menu Cleaning
Eject
154℃
100% 100%
Menu Cleaning
Eject
154℃
2. Hold the side of the stacker and lift the card as image below to remove it.
35
Collect cards
POINTMAN NR Serise User Guide Manual
Other manuals for NR Series
1
Table of contents
Other Pointman Printer manuals
