Polanik W-4355-S User manual

Technical specification
Instruction manual
High jump school landing area, made of mats
W-4355-S
File: 2015-09-01
PRODUCT SUPPORT
Pawel Ciechanowski
p.ciechano[email protected]m

Technical specification /Instruction manual W-4355-S 2/6
Thank you for purchasing POLANIK landing area.
Safe assembly and use
ATTENTION! VACCUM PACKED PRODUCT –UNPACK IMMEDIATELY AFTER DELIVERY
Before you start to assemble and use the landing area please read this manual carefully and store the manual in a
safe place for further reference. Polanik shall not be liable for any cage damages which are the result of the failure
to follow this manual.
Unauthorized copying of this manual, in whole or in part, is prohibited.
The contents of this manual are subject to change without notice.
Warning! The sports equipment produced by Polanik is designed for athletics training and use in sports competitions
only. Please pay special attention when using the product, misuse of athletics equipment can cause serious injury or
in extreme cases even death. That is why training and use during sports events have to be always supervised by
authorized sports personnel. In no event shall Polanik be liable for any special, incidental, indirect or consequential
damages in connection with the purchase or use of POLANIK products or costs over the original cost of the product.
Specific warranty terms:
1) The use of the landing area outdoors requires a waterproof cover and a landing area platform for proper
insulation from the ground. Failure to follow the above restrictions results in the loss of the warranty rights.
2) The top pad of the landing area is equipped with a spike resistant mesh fabric. The mesh fabric is designed to
protect the landing area against spikes used by jumpers. While landing and walking on the top pad the spikes
go through the mesh fabric and do not damage the surface. One must not shuffle the spikes on the mesh
fabric, because under high crosswise stress caused by moving the spikes without lifting the feet, it may happen
that the top pad will be torn. The damages of the top pad caused by careless sliding the pikes on the top pad
surface are excluded from the warranty and can be removed in course of payable repair or replacement of the
landing area elements.

Technical specification /Instruction manual W-4355-S 3/6
I. General description
POLANIK landing area W-4355-S is a school top quality sports equipment which is designed to secure jumpers and
absorb impact energy of a jumper’s landing after take-off and flight in high jump training.

Technical specification /Instruction manual W-4355-S 4/6
II. Technical specification
Landing area
Code
W-4355-S
PN-EN 12503-2 type
9
Dimensions length / width / height [m]
4 / 3 / 0,55
Spike resistant surface
upper surface of top pad is equipped with spike resistant mesh fabric
Segment covering
PVC, made of polyester with two vinyl layers
Weight [kg]
115 kg
Safety mattress
PN-EN 12503-1 type
4
Dimensions length / width / height [m]
3/2/0,25
Number of segments [pcs]
4
Weight [kg]
27
Internal structure
high quality PUR foam
Segment covering
PVC, made of polyester with two vinyl layers
Bottom
anti-skid surface
Way of segment linking
jacquard webbing with Velcro
Carrying handles
very strong jacquard webbing, firmly attached by means of envelope
stitching
[mm]

Technical specification /Instruction manual W-4355-S 5/6
III. Preparing for first use
The landing area elements are vacuum packed only for transport. Please unpack them immediately after delivery and
leave them in a roofed place for few hours, so that they can return to their original shapes. Storing vacuum packed
landing area elements may cause permanent damages in their internal structures. When the landing area elements
return to their original dimensions, you can place them in high jump field. The field surface should be even, smooth and
without any obstacles.
IV. Assembly
It is done in 3 easy steps:
Place the first layer of the mats,
then link them using Velcro® belts and D-rings,
when the first layer of the mats is ready, put
another one on it,
then link the mats using Velcro® belts and D-rings,
next cover the layers with the master cover, so that
the anti-spike surface is on top if practising in
special footwear with spikes, or use the smooth
surface, which is designed for jumping in sports
footwear and is also used to protect the landing
area against weather conditions,
the landing area is ready for use.
V. Operating
Stepping on the landing area and practising require special footwear designed for those purposes. Treading on the
landing area in footwear with spikes is only allowed when the landing area is equipped with special spike resistant
surface. Stepping on the landing areas in hard footwear or in shoes with heels is strongly prohibited. You must not put
any tables, chairs, benches or any other objects whose unit pressure exceeds 1kg/1cm2on the landing area. If the
landing area is moved from one place to another very often, it is recommended that a landing area cart should be
used.
VI. Maintenance
Due to the hygiene requirements it is recommended that the landing area should be cleaned regularly with commonly
available detergents. Before you start wiping the landing area, please try to clean a small spot on its bottom side in
order to check the reaction with the PVC fabric.
VII. Storing
The landing area segments should be preferably stored in a horizontal position. A vertical position is also possible,

Technical specification /Instruction manual W-4355-S 6/6
provided that they are not deformed and the mats stand straight. They cannot be bent or pressed by any objects during
storing. That may deform them permanently. A storing facility should be clean and dry. It ought to provide min.
temperature 5º C.
VIII. Declaration
1)No. 2015-09-01
2)Issuer’s name: POLANIK
Issuer’s address: Życzliwa 11, 97-300 Piotrkow Tryb.
3)Object of declaration:
4)The object of declaration described above is in conformity with the requirements of the following documents:
Document No.
Title
Edition/Date of issue
Position
PN-EN 12503-2
Sports mats –Part 2: Pole vault and high
jump mats, safety requirements
April 2004
All above
Additional Information
5)Declaration for:
BUYER and USER
Signed for and in behalf of:
POLANIK
2015-09-01 Piotrkow Tryb.
(Date and place of issue)
Pawel Ciechanowski
Product Manager
6)……………………………………… ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
Position
Description
Code
1
High jump school landing area 4 x 3 x 0,55 m
W-4355-S