Polanik W-536-B User manual

INSTRUCTION MANUAL
High jump club landing area
monocube
W- 36-B
File: 2014-07-18
PRODUCT SUPPORT
Pawel Ciechanowski
p.ciechanowski polanik.com

Instruction manual W-536-B 2/4
Thank you for choosing POLANIK landing area.
Contents
Chapter Page
I. General description 2
II. Technical specification 2
III. Preparing for first use 2
IV. Assembly 3
V. Operating 3
VI. Maintenance 3
VII. Storing 3
VIII. Declarations and certificates 4
I. General description
POLANIK landing area W-536-B is top quality sports equipment which is designed to secure jumpers and absorb
impact energy of a jumper’s landing after take off and flight in high jump training.
II. Technical specification
Code W- 36-B
Dimensions length / width / height [m] 5 / 3 / 0,6
Weight [kg] 157,50
Foam units 2 pcs, advanced 3-layer construction, made of high quality PUR
foam, overlapped to eliminate empty spaces between units
PVC master covering made of polyester with two vinyl layers, upper surface is equipped
with spike resistant mesh fabric, zipper closure
Way of waterproof cover linking Velcro® belts
[mm]
III. Preparing for first use
The landing area foam units are vacuum packed only for transport. Please unpack them immediately after delivery and
leave them in a roofed place for few hours, so that they can return to their original shapes. Storing vacuum packed
foam units may cause permanent damages in their structures. Please keep the plastic transport bags for future use.
When the units return to their original dimensions, you can place them in high jump field. The field surface should be
even, smooth and without any obstacles. If you use the landing area outdoors, you should also provide: a special
waterproof cover P-536-B to protect the landing area against unfavourable weather conditions and a modular
platform SW-5x3 to insulate the landing area from the ground.

Instruction manual W-536-B 3/4
IV. Assembly
It is done in 4 easy steps:
1
place the PVC master covering on the surface
where the landing area is to be situated,
2
then put the first foam unit onto the covering,
3
next put the other unit onto the covering, so
that it overlaps the first one,
4
then cover the units and zip the master
covering. The landing area is ready for use.
V. Operating
Stepping on the landing area and practising require special footwear designed for those purposes. Treading on the
landing area in footwear with spikes is only allowed when the landing area is equipped with special spike resistant
surface. Stepping on the landing areas in hard footwear or in shoes with heels is strongly prohibited. You must not
put any tables, chairs, benches or any other objects whose unit pressure exceeds 1kg/1cm
2
on the landing area.
Please note that the foam units are not designed to be taken from the PVC master covering. Since the units have not
got their own coverings, the foam is vulnerable to damages when you remove the units from the PVC master
covering. Therefore if you are forced to remove them from the master covering, please do that carefully and store
the units in their transport plastic bags.
VI. Maintenance
Due to the hygiene requirements it is recommended that the landing area should be cleaned regularly with
commonly available detergents. Before you start wiping the landing area, please try to clean a small spot on its
bottom side in order to check the reaction with the PVC fabric.
VII. Storing
The landing area can be stored only in a horizontal position. It cannot be bent or pressed by any objects during
storing. That may deform it permanently. A storing facility should be clean and dry. It ought to provide min.
temperature 5 ºC.
Even the best technical solutions cannot substitute for common sense. The usage of the product must take place
under the supervision of qualified coaches. The producer shall not be liable for any incidents caused by the improper
assembly or its misuse. The producer reserves the right to introduce without warning changes in product
constructions and colours.

Instruction manual W-536-B 4/4
VIII. Declaration of conformity
1) No. 2009-06-25
2) Issuer’s name: POLANIK Sp. z o. o.
Issuer’s address: Życzliwa 11, 97-300 Piotrkow Tryb.
3) Object of declaration:
4) The object of declaration described above is in conformity with the requirements of the following documents:
Document No. Title Edition/Date of issue Position
PN-EN 12503-2 Sports mats – Part 2: Pole vault and high jump
mats, safety requirements April 2004 All above
Additional Information
5) Declaration for:
BUYER and USER
Signed for and in behalf of:
POLANIK.
2014-07-18 Piotrkow Tryb.
(Date and place of issue)
Pawel Ciechanowski
Product Manager
6) ……………………………………… ……………………………………………………………………………
(Name, function) (Signature or equivalent authorized by the issuer)
Position Description Code
1 High jump club landing area monocube 5 x 3 x 0,6 m W- 36-B