Polar Electro UA014-A User manual

Model:
UA014-A / UA015-A / UA016-A
Blast Chiller
Instruction manual
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 1UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 1 2020/9/2 10:102020/9/2 10:10

2
AU Telephone Helpline: 1300225960
Safety Tips
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components or service panels on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- Fire Precautions
- Wiring Regulations
- Building Regulations
• DO NOT use jet/pressure washers to clean the appliance.
• DO NOT use the appliance outside.
• DO NOT use this appliance to store medical supplies.
• DO NOT use electrical appliances inside the appliance
(e.g. heaters, ice cream makers, etc.)
• DO NOT allow oil or fat to come into contact with the plastic
components or door seal. Clean immediately if contact occurs.
• Always carry, store and handle the appliance in a vertical
position and move by holding the base of the appliance.
• Always switch off and disconnect the power supply to the unit
before cleaning.
• Keep all packaging away from children. Dispose of the
packaging in accordance with the regulations of local
authorities.
• If the power cord is damaged, it must be replaced by a POLAR
agent or a recommended qualified technician in order to avoid
a hazard.
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 2UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 2 2020/9/2 10:102020/9/2 10:10

3
AU
Telephone Helpline: 1300225960
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience or knowledge, unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
• Polar recommends that this appliance should be periodically
tested (at least annually) by a Competent Person. Testing
should include, but not be limited to: Visual Inspection,
Polarity Test, Earth Continuity, Insulation Continuity and
Functional Testing.
Caution Risk of Fire
• Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
Warning: Keep all ventilation openings clear of
obstruction. Unit should not be boxed in without
adequate ventilation.
• Warning: Do not use mechanical devices or other means
to accelerate the defrosting process, other than those
recommended by the manufacturer.
• Warning: Do not damage the refrigerant circuit.
• Warning: Do not use electrical appliances inside the food
storage compartments of the appliance, unless they are the
type recommended by the manufacturer.
Product Description
UA014-A - POLAR Blast Chiller with Touch screen Controller (3 x 1/1GN)
UA015-A - POLAR Blast Chiller with Touch screen Controller (5 x 1/1GN)
UA016-A - POLAR Blast Chiller with Touch screen Controller (10 x 1/1GN)
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of
this machine will provide the best possible performance from your POLAR product.
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 3UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 3 2020/9/2 10:102020/9/2 10:10

4
AU Telephone Helpline: 1300225960
Pack Contents
The following is included:
• POLAR Blast Chiller
• Instruction manual
POLAR prides itself on quality and service, ensuring
that at the time of packaging the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit,
please contact your POLAR dealer immediately.
Installation
Note: If the unit has not been
stored or moved in an upright
position, let it stand upright for
approximately 12 hours before
operation. If in doubt allow to
stand.
1. Remove the appliance from the packaging.
Make sure that all protective plastic film and
coatings are thoroughly removed from all
surfaces.
2. Maintain a distance of 20cm (7 inches)
between the unit and walls or other objects for
ventilation. NEVER LOCATE NEXT TO OR
NEAR A HEAT SOURCE.
Note: Before using the appliance
for the first time, clean the
interior with soapy water.
3. Set the brakes on the castors to keep the
appliance in position.
Operation
Storing Food
To get the best results from your POLAR appliance,
follow these instructions:
• It is important that food entering the Blast
Chiller/Freezer does not exceed a temperature
of 90°C.
• It is recommended that metal containers /
trays are used as other materials such as
plastic or polystyrene containers will act as an
insulator and extend blast chilling times.
• Sufficient space must be left between products
in order to guarantee a sufficient flow of cold
air. Ensure product is not in contact with the
internal walls of the unit, and leave sufficient
gaps between trays.
• Never obstruct the inlet of the evaporator fans.
• Products that are more difficult to chill because
of their composition and size should be placed
in the centre of the unit.
• Blast chilling data refers to standard products
(low fat content) with a thickness below
50 mm: therefore avoid overlaying products
on trays or the insertion of pieces with a
much higher thickness, as this will lead to
an extension of blast chilling times. Always
distribute the product well on the trays and in
the case of thick pieces decrease the amount
to blast chill.
• Limit the number of times and the duration of
time the doors are opened.
• The chiller should be used for storage for short
periods only.
• When removing product that has undergone
blast chilling/shock freezing, always wear
gloves to protect hands from cold burns.
Insert the food probe
• Before selecting which cycle to use, the probe
must be inserted into the food. This allows
the internal temperature of the food to be
measured.
• It is important that the probe is correctly
connected to the unit, or an alarm will activate
and the appliance will not function.
Note: To prevent bacterial
contamination or contamination
of any other biological nature,
the needle probe must be
disinfected after use.
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 4UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 4 2020/9/2 10:102020/9/2 10:10

5
AU
Telephone Helpline: 1300225960
User interface
Initial information
The interface has the following operating modes:
• Off: No power to the device
• Stand-by: The device is powered but switched
off
• On: The device is powered, switched on and
awaiting start-up of an operating cycle
• Run: The device is powered, switched on and
running an operating cycle
Initial switch-on
Connect the appliance to the mains power supply.
The appliance will show the loading screen. When
loading completed, the display will show:
• the Home screen if pressing the central area in
the On/Standby screen
• the Home screen directly
Press this bottom area
to switch off
On/Standby screen Home screen
Press this central area
to switch on
Notes:
• “Switch on the device” means moving from
“Stand-by” to “On” mode;
• “Switch off the device” means moving from
“On” to “Stand-by” mode.
• If the power supply fails during “stand-by” or
“on” mode, when power is restored the device
will return to the mode set before the failure.
Note: If the power supply has been cut off
long enough to cause a clock error (RTC
code), it will be necessary to reset the
date and time. The date and time can be
set from the settings screen (For details,
please see “Section 12.1” in the controller
manual supplied with the appliance).
Selecting the screen language
1. While in the Home screen, press the set key
on the left top.
2. The display will show the Setting menu as
below:
3. Press “LANGUAGE” to display the language
menu:
4. Press the desired language to confirm (Note:
The default language is English).
Unlock keypad
If the keypad is locked, a menu will pop up when it
is touched. Slide the finger rightward to unlock.
Silencing the buzzer
Press any key while buzzer sounding to cease.
Door-open signal
When the door is opened, the signal will
appear on the display. Press any area on the
display to remove this signal.
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 5UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 5 2020/9/2 10:102020/9/2 10:10

6
AU Telephone Helpline: 1300225960
Selecting the operating mode
The operating functions can be accessed from the Home screen by
selecting the desired area.
Note:
For the use of the appliance, please follow the screen
indications for instant operations. Or alternatively you can
refer to the controller manual supplier with the appliance
for details.
Press this area to select a cabinet pre-cooling cycle.
(For details, see Section 10 in the controller manual supplied with the
appliance.)
Blast chilling mode. Under this mode, you can select/set a standard blast
chilling/blast-freezing cycle, a multi-needle probe or multi-timer cycle.
(For details, see Section 7 in the controller manual supplied with the
appliance.)
Special cycles mode:
Under this mode, only the
probe heating function is
supported.
(For details, see Sections
6.2 and 8.6 in the
controller manual supplied
with the appliance.)
Makes it possible to access the recipe book mode, where pre-saved recipes
are available for selection.
(For details, see Section 9 in the controller manual supplied with the
appliance.)
This area will appear if an alarm is activated.
Press this area to see the historical data stored during operation.
(For details, see Sections 7.6.2 and 12.2 in the controller manual supplied
with the appliance.)
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 6UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 6 2020/9/2 10:102020/9/2 10:10

7
AU
Telephone Helpline: 1300225960
Cleaning, Care & Maintenance
Switch off and disconnect from the power supply before cleaning.
• Clean the interior of the appliance as often as possible.
• Do not use abrasive cleaning agents. These can leave harmful residues.
• Clean the door seal with water only.
• Always wipe dry after cleaning.
• Do not allow water used in cleaning to run through the drain hole into the evaporation pan.
• Take care when cleaning the rear of the appliance. Sharp edges can cut.
• A POLAR agent or qualified technician must carry out repairs if required.
Stainless Steel Care
To maintain the stainless steel exterior of your Polar item, please consider the following information:
Never:
• Use abrasive Scourers or scrubbing pads, etc.
• Use Chlorinated or acidic detergents
• Allow anything e.g. food, dirt, cleaning chemicals to remain on the surface for longer than necessary,
clean them off right away.
• Allow the surface to remain wet.
Do:
• Clean often.
• Use soft Cloths or plastic Scourers.
• Rub with the grain of the metal, rather than across it.
• Use detergents and polish designed for cleaning Stainless Steel.
• Ensure that the cleaning products are washed off fully and that the steel is left dry.
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 7UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 7 2020/9/2 10:102020/9/2 10:10

8
AU Telephone Helpline: 1300225960
Cleaning the evaporator
• Clean the evaporator periodically.
• As the fins of the evaporator are very sharp. Always wear protective gloves.
• Only a brush can be used for cleaning. Do not use jets of liquid or sharp instruments.
• To access the evaporator proceed as follows:
1. Open the door (A) of the appliance.
2. Loosen the two screws (B) on the right of the deflector.
3. Remove the runner (C).
4. Turn the deflector (D) to the left.
B
A
B
C
D
1
Cleaning the condenser
• Clean the condenser periodically.
• As the fins of the condenser are very sharp, always wear protective gloves.
• Use protective masks and glasses in the presence of dust.
• Whenever the condenser has a deposit of dust in correspondence with the fins, this can be removed
using a suction device or with a brush applied, using a vertical movement along the direction of the
fins.
• No other instruments must be used, which may deform the fins and therefore the efficiency of the
appliance.
• To clean, proceed as follows:
1. Open the door (A) of the appliances.
2. Remove the lower panel (B). To do this, remove the screw fasteners (C).
3. It is now possible to clean the finned part of the condenser (D) using suitable tools and protection
devices.
4. After cleaning, close the control panel and fix it with the screws removed beforehand.
2
A
B
C
D
C
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 8UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 8 2020/9/2 10:102020/9/2 10:10

9
AU
Telephone Helpline: 1300225960
Troubleshooting
If your POLAR appliance develops a fault, please check the following table before making a call to the
Helpline or your POLAR dealer.
Fault Probable Cause Solution
The appliance is not
working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug and lead are damaged Call POLAR agent or qualified Technician
Fuse in the plug has blown Replace the fuse
Power supply Check power supply
Internal wiring fault Call POLAR agent or qualified Technician
The appliance is
leaking water
The appliance is not properly
levelled
Adjust the screw feet to level the appliance
(if applicable)
The drain is blocked Clear the discharge outlet
Movement of water to the drain is
obstructed
Clear the floor of the appliance (if
applicable)
The water container is damaged
if water is leaking from back of
container
Call POLAR agent
The appliance is
unusually loud
The appliance has not been
installed in a level or stable
position
Check installation position and change if
necessary
Loose nut/screw Check and tighten all nuts and screws
The appliance is not
chilling
Wrong program Change program – see controller manual
The filter is blocked Clean filters
Temperature of food is
not being detected
The food probe is broken Purchase a new food probe from your
Distributor
Food has freezer burns
after removing from
unit
The selected cycle is not suitable
for the food
Change cycle from hard freeze to soft
freeze ( Selecting the operating mode)
The appliance is
beeping and there is a
message appearing on
the control panel
There is a problem with the unit
being indicated by the control
alarm signal
See table below
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 9UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 9 2020/9/2 10:102020/9/2 10:10

10
AU Telephone Helpline: 1300225960
Control panel
message/code
Meaning Required action
RTC Clock error Re-set date and time. For details, see “Section
12.1: Service” in the controller manual supplied
with the appliance
CABINET PROBE Cabinet probe error • Check that the probe is undamaged
• Check the device-probe connection
• Check the cabinet temperature
• If problem persists, Call POLAR agent or
qualified technician.
EVAPORATOR PROBE Evaporator probe error Same as for the cabinet probe error but with
reference to the evaporator probe
CONDENSER PROBE Condenser probe error Same as for the cabinet probe error but with
reference to the condenser probe
NEEDLE PROBE
SENSOR 1/2/3
Needle probe/sensor 1/2/3
error
Same as for the cabinet probe error but with
reference to needle probe 1/2/3
NEEDLE PROBE Needle probe alarm (all
the needle probe sensors
enabled are in alarm
status)
Same as for the cabinet probe error but with
reference to all the needle probes
NEEDLE PROBE
INSERTION
Needle probe not inserted
alarm
Check that the needle probes have been correctly
inserted
DOOR OPEN Door open alarm Check the door status
HIGH TEMPERATURE Maximum temperature
alarm (HACCP alarm)
• Check the cabinet temperature
LOW TEMPERATURE Minimum temperature
alarm (HACCP alarm)
• Check the cabinet temperature
POWER FAILURE Power failure alarm (HACCP
alarm)
Check the device-power supply connection
Note: This table just lists very basic alarms. For more detailed alarm information, please
see “Section 16 Alarms” in the controller manual.
Technical Specifications
Model Voltage Power Capacity Weight
(kg)
Temperature
range Refrigerant Dimensions H x W x D
UA014-A 220-240V~
50Hz
700W 3 x GN1/1 104 +5°C ~ -35°C R290 965 x 804 x 826
UA015-A 220-240V~
50Hz
720W 5 x GN1/1 116 +5°C ~ -35°C R290 1035 x 804 x 826
UA016-A 220-240V~
50Hz
900W 10 x GN1/1 150 +5°C ~ -35°C R290 1885 x 800 x 815
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 10UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 10 2020/9/2 10:102020/9/2 10:10

11
AU
Telephone Helpline: 1300225960
Electrical Wiring
The plug is to be connected to a suitable mains socket.
POLAR appliances are wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E
This appliances must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The product must not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and environmentally safe
recycling process. For further information on how to dispose of this product correctly, contact the product
supplier, or the local authority responsible for waste disposal in your area.
POLAR parts have undergone strict product testing in order to comply with regulatory
standards and specifications set by international, independent, and federal authorities.
POLAR products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of POLAR.
Every effort is made to ensure all details are correct at the time of going to press, however, POLAR reserve the right to
change specifications without notice.
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 11UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 11 2020/9/2 10:102020/9/2 10:10

DECLARATION OF CONFORMITY
•Conformiteitsverklaring • Déclaration de conformité • Konformitätserklärung • Dichiarazione di conformità •
•Declaración de conformidad • Declaração de conformidade
Equipment Type • Uitrustingstype • Type d'équipement • Gerätetyp
• Tipo di apparecchiatura • Tipo de equipo • Tipo de equipamento
Model • Modèle • Modell • Modello
• Modelo • Malli
Blast Chiller 3 x 1/1GN - with Touchscreen Controller
Blast Chiller 5 x 1/1GN - with Touchscreen Controller
Blast Chiller 10 x 1/1GN - with Touchscreen Controller
UA014
UA015
UA016
Application of Territory Legislation &
Council Directives(s)
Toepassing van Europese Richtlijn(en)
• Application de la/des directive(s) du
Conseil • Anwendbare EU-Richtlinie(n)
• Applicazione delle Direttive
• Aplicación de la(s) directiva(s) del
consejo • Aplicação de directiva(s) do
Conselho
Machinery Directive (MD) 2006/42/EC
EN 60335-1:2012 + AC:2014 + A11:2014 +
A13:2017
EN 60335-2-89:2010 +A1:2016+A2:2017
EN 62233:2008
Electro-Magnetic Compatibility (EMC)
Directive 2014/30/EU - recast of
2004/108/EC
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
Restriction of Hazardous Substances
Directive (RoHS) 2015/863 amending Annex
II to Directive 2011/65/EU
Electrical Safety
EN 60335-1:2012 + AC:2014 + A11:2014 +
A13:2017
EN 60335-2-89:2010 +A1:2016+A2:2017
Electromagnetic Compatibility
EN 55014-1:2017
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers
• Nome del produttore • Nombre del fabricante • Nome do fabricante
Polar
Producer Address • Adres fabrikant •
Adresse du producteur • Anschrift des
Herstellers • Indirizzo del produttore •
Dirección del fabricante • Morada do
fabricante
Fourth Way,
Avonmouth,
Bristol,
BS11 8TB
United Kingdom
42 North Point
Business Park
New Mallow Road
Cork
Ireland
15 Bagdally Road,
Campbelltown
NSW 2560
I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation,
Directive(s) and Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande
Richtlijn(en) en Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und Norm(en)
entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y estándar(es)
arriba mencionadas.
Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es)
Directiva(s) e Norma(s)
Date • Data • Date • Datum • Data • Fecha • Data
19th June 2020
Signature • Handtekening • Signature • Unterschrift
Firma • Firma • Assinatura
Full Name • Volledige naam • Nom et prénom •
Vollständiger Name • Nome completo
•Nombre completo • Nome por extenso
Ashley Hooper
Josie Holt
Position • Functie • Fonction • Position • Qualifica
•Posición • Função
Technical & Quality Manager
Commercial Manager/
Responsible Supplier
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 12UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 12 2020/9/2 10:102020/9/2 10:10

UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 13UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 13 2020/9/2 10:102020/9/2 10:10

UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 14UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 14 2020/9/2 10:102020/9/2 10:10

UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 15UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 15 2020/9/2 10:102020/9/2 10:10

UA014-A_UA015-A_UA016-A_A5_v1_20200902
http://www.polar-refrigerator.com/
UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 16UA014-A_UA015-A_UA016-A_A5_v1_20200902.indb 16 2020/9/2 10:102020/9/2 10:10

EVCO S.p.A. Vcolor 869 | Installer manual ver. 1.0 | Code 144VC869E104
page 1 of 9
Vcolor 869
Controllers for blast chillers with customizable
graphical skin
ENGLISH
INSTALLE MANUAL ver. 1.0
CODE 144VC869E04

EVCO S.p.A. Vcolor 869 | Installer manual ver. 1.0 | Code 144VC869E104
page of 9
Important
Read this document carefully before installation and before using the device and take all the prescribed precautions.
Keep this document with the device for future consultation.
Only use the device in the ways described in this document. Do not use the device as safety device.
The following symbols are used in this document:
indicates a suggestion
indicates a warning.
Disposal
The device must be disposed of according to local regulations governing the collection of electrical and electronic waste.

EVCO S.p.A. Vcolor 869 | Installer manual ver. 1.0 | Code 144VC869E104
page 3 of 9
Index
1 INTRODUCTION ................................................................................................................................... 6
1.1 Introduction ........................................................................................................................................ 6
1. Main features of the models available ..................................................................................................... 7
DESCRIPTION .................................................................................................................................... 10
.1 User interface description .................................................................................................................... 10
. Control module description .................................................................................................................. 1
3 MEASUREMENTS AND INSTALLATION ................................................................................................... 13
3.1 Vcolor 869M user interface measurements ............................................................................................ 13
3. Vcolor 869L user interface measurements ............................................................................................. 13
3.3 Control module measurements ............................................................................................................ 14
3.4 Multi-functional module measurements ................................................................................................. 14
3.5 User interface installation .................................................................................................................... 15
3.6 Control and multi-functional module installation ..................................................................................... 16
3.7 Installation precautions ....................................................................................................................... 16
4 ELECTRICAL CONNECTION .................................................................................................................. 17
4.1 Electrical connection of Vcolor 869M ..................................................................................................... 17
4. Electrical connection of Vcolor 869L ...................................................................................................... 19
4.3 Precautions for electrical connection ..................................................................................................... 0
5 USER INTERFACE ............................................................................................................................... 1
5.1 Initial information .............................................................................................................................. 1
5. Initial switch-on ................................................................................................................................. 1
5.3 Switching the device on and off ........................................................................................................... 3
5.4 Lock/unlock keypad ............................................................................................................................ 3
5.5 Silencing the buzzer ........................................................................................................................... 3
5.6 Door-open signal................................................................................................................................ 3
6 OPERATION ....................................................................................................................................... 4
6.1 Initial information on operating cycles .................................................................................................. 4
6. Initial information on the needle probe ................................................................................................. 4
6.3 Selecting the operating mode .............................................................................................................. 5
7 BLAST CHILLING ................................................................................................................................ 6
7.1 Blast chilling/blast-freezing and conservation ........................................................................................ 7
7.1.1 Combined cycle with slow cooking ................................................................................................ 9
7. Hard blast chilling/soft blast-freezing and conservation ................................................................................ 9
7.3 Continuous cycle ................................................................................................................................ 30
7.3.1 Multineedle probe mode .............................................................................................................. 30
7.3. Multi-timer mode ........................................................................................................................ 31
7.4 Customized cycle ............................................................................................................................... 3
7.5 Setting the set points ......................................................................................................................... 33
7.5.1 Setting the cabinet temperature set point ...................................................................................... 33
7.5. Setting the product temperature set point ..................................................................................... 33
7.5.3 Setting the cycle duration ............................................................................................................ 33
7.5.4 Setting the fan speed .................................................................................................................. 33
7.6 Running the cycle............................................................................................................................... 34
7.6.1 Needle probe insertion test .......................................................................................................... 34
7.6. Recording historical data ............................................................................................................. 35
7.6.3 Cycle end .................................................................................................................................. 35
8 SPECIAL CYCLES ................................................................................................................................ 37

EVCO S.p.A. Vcolor 869 | Installer manual ver. 1.0 | Code 144VC869E104
page 4 of 9
8.1
Fish sanitation ................................................................................................................................... 38
8. Thawing ............................................................................................................................................ 40
8.3 Defrosting ......................................................................................................................................... 4
8.4 Ice cream hardening........................................................................................................................... 43
8.5 Cabinet sterilisation ............................................................................................................................ 44
8.6 Heating the needle probe .................................................................................................................... 45
8.7 Drying .............................................................................................................................................. 45
8.8 Retarding proofing ............................................................................................................................. 46
8.8.1 Description of retarding proofing .................................................................................................. 46
8.8. Setting up a retarding proofing cycle ............................................................................................ 48
8.9 Slow cooking ..................................................................................................................................... 50
8.10 Conservation ................................................................................................................................. 5
9 RECIPE BOOK .................................................................................................................................... 53
9.1 "COOKBOOK" recipe book ................................................................................................................... 53
9. "MY COOKBOOK" recipe book .............................................................................................................. 54
9. .1 Saving “MY COOKBOOK” recipes .................................................................................................. 54
9. . Starting “MY COOKBOOK” recipes ................................................................................................. 56
9. .3 Deleting “MY COOKBOOK” recipes ................................................................................................ 56
10 PRE-COOLING.................................................................................................................................... 57
11 ADJUSTMENTS ................................................................................................................................... 58
11.1 Door frame heating output .............................................................................................................. 58
11. Compressor management................................................................................................................ 58
11.3 Gestione secondo compressore ........................................................................................................ 59
11.4 Pump down solenoid valve management ........................................................................................... 59
11.5 Evaporator fan management............................................................................................................ 59
11.6 Condenser fan management ............................................................................................................ 61
11.7 Alarm output management .............................................................................................................. 61
11.8 Needle probe heating management .................................................................................................. 61
11.9 Cabinet sterilisation management..................................................................................................... 61
11.10 Defrost output management ............................................................................................................ 61
11.11 Thawing heater management........................................................................................................... 6
11.1 Proofing and slow cooking heater management .................................................................................. 6
11.13 Humidifier management .................................................................................................................. 6
11.14 Humidifying/steam generator heater management ............................................................................ 6
11.15 Cabinet light management............................................................................................................... 6
1 SETTINGS ......................................................................................................................................... 63
1 .1 Time and date ............................................................................................................................... 63
1 . Service ......................................................................................................................................... 63
1 .3 Internal values ............................................................................................................................... 63
1 .4 Select language ............................................................................................................................. 63
13 USING THE USB PORT ........................................................................................................................ 64
13.1 Initial information ........................................................................................................................... 64
13.1.1 Uploading program settings (USB  controller) .............................................................................. 64
13.1. Downloading program settings (controller -> USB) ......................................................................... 64
13.1.3 Uploading configuration parameter settings (USB  controller) ........................................................ 64
13.1.4 Downloading configuration parameter settings (controller -> USB) ................................................... 65
13.1.5 Downloading HACCP data (controller -> USB) ................................................................................ 65
14 EPOCA CLOUD PLATFORM ................................................................................................................... 66
15 LIST OF CONFIGURATION PARAMETERS ............................................................................................... 67