Polaris 2882859 User manual

APPLICATION
Verify accessory fitment at Polaris.com.
BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
KIT CONTENTS
This Kit includes:
Kit PN 2882915
REF QTY PART DESCRIPTION PART NUMBER
1 1 Rear Bumper 2635905
2 1 Hitch Adapter 1023413
3 1 Forged Hitch Assembly 1023736
4 2 Screw - M8 X 1.25 X 20 7518450
52 Screw - M8 X 1.25 X 50 7520105
6 2 Nut, Hex Flange - M8 X 1.25 7547317
7 6 Screw - M6 X 1.0 X 20 7518616
8 2 Rivet - 3/16” 7621433
Instr 9928014 Rev 02 2017-08 Page 1 of 5
P/N 2882859;2882915
AXYS®® 144 HITCH KIT

Instr 9928014 Rev 02 2017-08 Page 2 of 5
REF QTY PART DESCRIPTION PART NUMBER
9 2 Rivet Washer - .20 X .67 X .048 7556034
1 Instructions 9928014
Kit PN 2882859
REF QTY PART DESCRIPTION PART NUMBER
1 1 Rear Bumper 2635905
2 1 Hitch Adapter 1023413
3 1 Hitch Mount 1023488
4 2 Screw - M8 X 1.25 X 20 7518450
5 2 Screw - M8 X 1.25 X 50 7520105
6 2 Nut, Hex Flange - M8 X 1.25 7547317
76 Screw - M6 X 1.0 X 20 7518616
8 2 Rivet - 3/16” 7621433
9 2 Rivet Washer - .20 X .67 X .048 7556034
10 2 Flat Washer - .390 X .750 X .065 7556188
11 1 Standard Hitch 1023491
12 1 Cotter Pin 7661407
13 1 Hitch Pin 7662337
1 Instructions 9928014

Instr 9928014 Rev 02 2017-08 Page 3 of 5
TOOLS REQUIRED
• Safety Glasses
• Pliers, Needle Nose
• Pop Rivet Puller
• Socket Set, Metric
• Socket Set, Torx®Bit
• Torque Wrench
• Wrench Set, Metric
IMPORTANT
Your AXYS®144 Hitch Kit is exclusively designed for your vehicle. Please read the installation instructions
thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to
ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.
ASSEMBLY TIME
Approximately 30 minutes
NOTE
Additional time may be required for optional steps, or
to accommodate other installed accessories.
INSTALLATION INSTRUCTIONS
1. Remove stock rear bumper A.
a. Remove two nuts Band two bolts Cthat
secure the rear bumper to the chassis from
each side of the vehicle.
Remove remaining fasteners Dsecuring snow
flap to the rear bumper as shown.
2. Install provided rear bumper q.
a. Place the rear bumper qthat was provided
with your kit into place by lining up the six
mounting holes as shown. Secure into place
using provided fasteners u. Torque to
specification provided.
TORQUE
6 Ft. Lbs. (8.5 Nm)

Instr 9928014 Rev 02 2017-08 Page 4 of 5
3. If installing Kit PN 2882895 see step 3a. If
installing Kit PN 2882915 see step 3b.
a. Kit PN 2882895
Install hitch mount eas shown. Secure into
place using providing fasteners r/t/y.
Torque to provided specification.
b. Kit PN 2882915
Install forged hitch assembly eas shown.
Secure into place using providing fasteners r/
t/y. Torque to provided specification.
TORQUE
20 Ft. Lbs. (27 Nm)
c. Secure snow flap to hitch assembly using
provided rivets iand washers oas shown.
If installing kit PN 2882895 continue to next
step. If installing kit PN 2882915, skip to step 4.
d. Install standard hitch sonto hitch mount as
shown using the provided hitch pin f, washers
aand cotter pin d.
After inserting the cotter pin into position bend
the individual legs of cotter pin din opposite
directions as shown below to properly secure
the hitch pin.
4. Check to ensure all tools are accounted for and all
steps have been completed.

Instr 9928014 Rev 02 2017-08 Page 5 of 5
FEEDBACK FORM
A feedback form has been created for the installer to provide any comments, questions
or concerns about the installation instructions. The form is viewable on mobile devices
by scanning the QR code or by clicking HERE if viewing on a PC.
FEEDBACK FORM