Ski-Doo MX User manual

operator's
manual
TI@ill@
414 6399 00 I

model
V.I.N.
purchase date
warranty expiry date
To be completed by dealer at time of sale
DEALER IMPRINT AREA
AFTER-SALES SERVICE
BOMBARDIER INC.
VALCOURT, QUEBEC
CANADA, JOE 2LO
The following are trademarks of Bombardier Inc.
u~
Qualify
Service
Litho'd in Canada
ALPINE®
BLIZZARD®
BOMBARDIER®
CARRY-BOOSE®
CHEYENNE*
CITATION®
ELAN®
ELITE®
ESCAPADE*
EVEREST®
FORMULA*
FUTURA®
GRAND PRIX SPECIAL®
MIRAGE®
MOTO-SKI®
NORDIK®
NUVIK®
OLYMPIQUE®
ROTAX®
SAFARI*
SAGA*
SCOUT*
SKANDIC®
SKI-DOO®
SONIC®
SPIRIT®
STRATOS*
T'NT®
TUNDRA*
VOYAGEUR*
®*Trademarks of Bombardier Inc. All rights reserved © Bombardier Inc.

FOREWORD __________________ _
The operator manual and the SSCC
Snowmobiler's Safety Handbook have
been prepared to acquaint the owner/
operator or passenger
of a new snow-
mobile with the various vehicle controls,
maintenance and safe operating instruc-
tions.
Each is indispensable for the proper
use
of the product, and should be kept
with the vehicle at all times.
Should you have any questions pertain-
ing to the warranty and its application,
please consult the
"Often Asked Ques-
tion" section of this manual, or your
authorized dealer.
This manual
uses the following symbols.
......... WARNING: Identifies an instruc-
T tion which, if not followed, could
cause serious personal injuries includ-
ing possibility of death.
..r CAUTION: Denotes an instruc-
T tion which, if not followed, could
severely damage vehicle components.
0 NOTE: Indicates supplementary
information needed to fully com-
plete
an instruction.
Although the mere reading
of such in-
formation does not eliminate the hazard,
your understanding
of the information
will promote its correct use.
......... WARNING: The engines and the
T orresponding components iden-
tified
in this manual should not be uti-
lized
on product(s) other than those
mentioned
on the cover page of this
manual.
.........
WARNING: Maintenance pro-
T cedures and tightening torques
must
be strictly adhered to, never at-
tempt repairs unless the appropriate
tools are available.
The information and components/sys-
tem descriptions contained
in this man-
ual are correct at time of publication.
Bombardier Inc. however, maintains a
policy
of continuous improvement of its
products
without imposing upon itself
any obligation to install them on prod-
ucts previously manufactured.
Bombardier
Inc. reserves the right at any
time to discontinue or change specifi-
cations, designs, features, models or
equipment without incurring obligation.
The illustrations show the typical con-
struction of the different assemblies and,
in all cases, may not reproduce the full
detail or exact shape of the parts shown,
however, they represent parts which
have the same or a similar function.
Most specifications are given in both
metric and customary units. Where pre-
cise accuracy
is not required, some con-
versions
are rounded off for easier use.
A shop manual can be obtained for com-
plete service, maintenance and repair in-
formation.
..r CAUTION: Most components of
T this vehicle are built with parts
dimensioned
in the metric system.
Most fasteners are metric and must
not
be replaced by customary fasten-
ers or vice versa. Mismatched or in-
correct fasteners could cause damage
to the vehicle or possible personal in-
jury.

SAFETY
MEASURES __________________________ _
Observe the following
precautions:
• Throttle mechanism should be checked
for free movement before starting engine.
•
Do not operate vehicle near snow making
equipment.
• The snowmobile engine can be stopped
by activating the emergency
cut-out or
tether switches or turning
off the key.
• Clean and check operation of the head-
light, tail light and brake light.
• Engine should
be running only when belt
guard and/or pulley guard
is secured in
place.
• Never run the engine
without drive belt
installed. Running
an unloaded engine can
prove to
be dangerous.
• Never run the engine
when the track is
raised off the ground.
• It can be dangerous to run engine
with
the hood removed.
• Gasoline
is flammable and explosive under
certain conditions. Always manipulate
in
a well ventilated area. Do not smoke or
allow open flames or sparks
in the vicinity.
If gasoline fumes are noticed while driving,
the cause should
be determined and cor-
rected
without delay.
• Maintain your vehicle
in top mechanical
condition
at all times.
• Your snowmobile
is not designed to be
driven or operated
on black top, bare earth,
or other abrasive surfaces.
On such sur-
faces abnormal and excessive wear ofcrit-
ical parts
is inevitable.
•
Your snowmobile is not designed to be
operated on public streets, road or high-
ways. In most States and Provinces, it
is
considered an illegal operation.
• Installation
of other than standard equip-
ment, including ski-spreaders, bumpers,
pack racks, etc., could severely affect the
stability and safety
of your vehicle. Avoid
adding
on accessories that alter the basic
vehicle configuration.
• Whenever the vehicle
is parked outdoors,
overnight or for a long period, it
is sug-
gested to protect it against the inclemency
of the weather with a snowmobile cover.
• Do
not lubricate throttle and/or brake ca-
bles and housings.
• Only perform procedures
as detailed in
this manual. Unless otherwise specified,
engine should be turned
OFF for all lubri-
cation and maintenance procedures.
• Since engine cooling
is fully in effect only
when the vehicle
is in motion and driven
on snow, it is
not recommended that you
altow the engine to idle for more than brief
periods and/or you drive the vehicle on
icy surfaces. Prolonged idling and/or con-
tinuous driving on ice may cause engine
damage.
• When removing coolant tank cap, first
place a cloth over cap then turn cap to
its first step to
release pressure. Never drain
or refill the cooling system when engine
is hot.
• These vehicles
are designed for the driver
only. No provisions have been made for
a passenger.
• The performance
of these vehicles may
significantly exceed
that of other snow-
mobiles
you have operated. Therefore, use
of this vehicle by novice or inexperienced
operators is
not recommended.
• Should removal
of a locking device be re-
quired when undergoing repairs/disassem-
bly, always replace by new ones. Tighten
fasteners
as specified in the applicable
Shop Manual.
PLEASE READ AND UNDERSTAND ALL
WARNINGS AND CAUTIONS
IN THE SNOW-
MOBILER'S SAFETY HANDBOOK, THE
OP-
ERATOR'S MANUAL AND ON THE VEHICLE
BOTH MANUALS SHOULD REMAIN WITH THE VEHICLE
AT THE TIME OF RESALE
2

INDEX ________________________ _
THE 1989 SNOWMOBILE LIMITED WARRANTY
OFTEN ASKED QUESTIONS ..... .
LISTING OF AREA DISTRIBUTORS .......... .
4
6
8
HOW TO IDENTIFY YOUR SNOWMOBILE . . . . . . . . . . . . . . . . . . . . . . . . 9
CONTROLS/INSTRUMENTS
Throttle lever, brake lever, ignition light switch, headlamp dimmer switch, emergency
cut-out switch, tether cut-out switch, rewind starter handle, primer, adjustable steer-
ing handle, speedometer, tachometer, temperature gauge, injection oil level pilot
lamp, high beam pilot lamp, tank cap, electric fuel level gauge, hood latch, tool bag,
spark plug holder, fuse holder, spare drive belt holder, fuel shut-off
valve, rear bumper,
accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
BREAK-IN PERIOD
Engine, belt, 10-hour inspection, 10-hour inspection check list ....... .
FUEL & OIL
Recommended gasoline, recommended oil, oil injection system ...... .
PRE-START CHECK
Check points ..
STARTING PROCEDURE
Manual starting, before riding, emergency starting
LUBRICATION
Frequency, steering and front suspension mechanism, drive axle, countershaft (brake
disc and driven pulleyL slide suspension, chaincase oil level, oil injection system,
rotary valve system . . . . . . . . .
............... .
MAINTENANCE
Service and maintenance chart, belt guard removal, drive belt removal and installa-
tion, drive belt condition, new drive belt, brake condition, brake adjustment, spark
plugs, suspension condition, suspension adjustment, limiter screw, track condition,
track tension and alignment, drive pulley, drive chain tensionner, steering and front
suspension mechanism, steering
and ski leg camber adjustment, muffler attachment,
engine head nuts, engine mount screws, air filter, carburetor adjustment, high alti-
tude kit, oil injection system, cooling system, headlamp beam aiming, bulb replace-
ment, general inspection
......................................... .
STORAGE
Track, suspension, skis and runners, controls, chaincase, drive pulley, countershaft
(brake disc and driven pulley), cooling system, engine lubrication, driven pulley, fuel
tank and carburetors, chassis, general inspection
..................... .
PRE-SEASON PREPARATION
Pre-season preparation chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... .
TROUBLE SHOOTING . . . . . . . ............................ .
TOOLS
................... .
SPECIFICATIONS ........................................ .
Sl METRIC INFORMATION GUIDE . . . . . . . . . . . . . . . . . . . . . ...... .
17
19
20
21
23
29
41
46
47
49
50
54
3

THE 1989 SNOWMOBILE
LIMITED WARRANTY _________ _
1 -PERIOD
BOMBARDIER INC. as manufacturer, warrants FROM THE DATE OF DELIVERY TO THE
FIRST CONSUMER, every 1989 BOMBARDIER® snowmobile, sold as NEW AND UNUSED,
and predelivered by
an authorized BOMBARDIER® dealer for a period of:
• 12 consecutive months.
2 - WHAT BOMBARDIER INC. WILL DO
BOMBARDIER INC. will repair and/or replace, at its option, components defective
in material and/or workmanship {under normal use and service), with a genuine
BOMBARDIER®. component without charge for parts or labour, at any authorized
BOMBARDIER® dealer during said
warranty period.
3- CONDITION TO HAVE WARRANTY WORK PERFORMED
Present to the servicing dealer, the hard copy of the BOMBARDIER® Warranty Registration
card or
proof of purchase received by the customer from the selling dealer at time of
delivery.
4 - WARRANTY TRANSFER
This warranty is transferable to subsequent owner(s) for remainder of warranty period
from original date of delivery.
5 - EXCLUSIONS - ARE NOT WARRANTED
• Normal wear on all items such as/ but not limited to:
drive belts -bulbs
slider shoes
-spark plugs -runners on skis
• Replacement parts and/or accessories
which are not genuine BOMBARDIER® parts
and/or accessories.
• Damage resulting
from installation of parts other than genuine BOMBARDIER® parts.
• Damage caused by failure
to provide proper maintenance as detailed in the Operator's
Manual. The labour, parts and
lubricants costs of all maintenance services, including
tune-ups and
adjustments will be charged to the owner.
• Vehicles designed and/or used
for racing purposes.
• All optional accessories installed on
the vehicle. (The normal warranty policy for parts
and accessories,
if any, applies).
• Damage resulting
from accident, fire or other casualty, misuse, abuse or neglect.
• Damage resulting
from operation of the snowmobile on surfaces other than snow.
• Damage resulting from
modification to the snowmobile not approved in writing by
BOMBARDIER INC.
• Losses incurred by
the snowmobile owner other than parts and labour, such as, but
not limited to, transportation, towing, telephone calls, taxis, or any other incidental
or consequential damage.
4

6 - BATTERY WARRANTY:
• 12 consecutive months. (Pro-rated)
100% warranty coverage will start on the date the snowmobile was delivered and
run
to the following April 30th. The remainder of the 12month-period will be pro-rated
as follows:
-
50% from April 30th to December 1st.
40% from December 1st to December 31st.
-
30% from January 1st to end of warranty.
7 - EXPRESSED OR IMPLIED WARRANTIES
This warranty gives you specific rights and you may also have other legal rights
which may vary from state to state, or province to province. Where applicable
this warranty is expressly in lieu of all other expressed or implied warranties of
BOMBARDIER INC., its distributors and the selling dealer, including any war-
ranty of merchantability or fitness for any particular purpose; otherwise the im-
plied warranty is limited to the duration of this warranty. However, some states
or provinces do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply.
Neither the distributor, the selling dealer, nor any other person has been autho-
rized to make any affirmation, representation or warranty other than those con-
tained in this warranty, and if made, such affirmation, representation or warranty
shall not be enforceable against BOMBARDIER INC. or any other person.
Some states or provinces do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply.
BOMBARDIER INC. reserves the right to modify its warranty policy at any time,
being understood that such modification will not alter the warranty conditions
applicable to vehicles sold while the above warranty is in effect.
8 - CONSUMER ASSISTANCE
If a servicing problem or other difficulty occurs, we suggest the following:
1. Try to solve the problem at the dealership with the Service Manager or Owner.
2. If this fails, contact your area distributor listed in the Operator's Manual.
3. Then if your grievance still remains unsolved, you may write to us:
Bombardier Inc.
Service
Department
Snowmobile Division
Valcourt (Quebec), Canada
JOE 2LO
September 1987
Bombardier Inc.
Valcourt (Quebec), Canada JOE 2LO
®*Trademarks of Bombardier Inc.
5

OFTEN ASKED
QUESTIONS __________________________ _
0: Why must my snowmobile be registered at the factory? After all I do have my
original invoice
as proof of when I purchased my snowmobile.
A: Your warranty is valid at anyauthorizeddealer of the product. Your registration
is the key element in providing the servicing dealer with the necessary data to
complete warranty claim forms. This information is also usedto
notify owners
in the event
of a safety recall.
0: Who should send the registration card to Bombardier Inc.?
A: The authorizeddealer. However, it is important that the customermake sure
that it has been sent. The company might contact you should your vehicle be
recalled
or in case of a particular warranty campaign.
0: I bought my snowmobile in O'King County but I snowmobile in Washington
County.
Can the dealer in Washington County accept to perform warranty work
on my snowmobile?
A: Yes, any authorized dealer in North America can perform warranty repairs,
providing the
customer warranty registration card is presented
0: Where can I find information on the lubrication and maintenance of my snow-
mobile?
A: In this Operator Manual provided with the vehicle at the time of delivery.
0: Will the entire warranty be void or cancelled, if I do not operate or maintain my
new snowmobile exactly
as specified in the Operator's Manual?
A: The warranty of the new snowmobile cannot be /;Voided" or ucancel/ed':
However,
if a particular failure is caused by operation or maintenance other
than is shown in the Operator Manual, THAT failure
may not be covered under
warranty. This includes service workperformedby the customer, especially the
criticaladjustments to ignition, timing, carburation
and allinjection/or all mixture.
0: Would you give some examples of abnormal use or strain, neglect or abuse?
6
A: These terms are general and overlap each other in areas. Some specific
examples
may include: running the machine out of of" chain failure caused by
a lack
of lubrication, operating the machine with a broken or damaged part
which causes another part to fail, and so on. If you have any specific questions
on operation
or maintenance, please contact your dealer for advice.

0: What costs are my responsibility during the warranty period?
A: The customer's responsibility includes all costs of normal maintenance
services, non-warrantyrepairs, accidents
and collision damage, as wellas oils,
and spark plugs, and incidental or consequential damage costs as explained
in the warranty.
0: Are ''Genuine" Bombardier replacement parts used in warranty repairs covered
by warranty?
A: Yes. When installed by an authorized dealer; any "Genuine"Bombardier part
used in warranty repairs assumes the remaining warranty that exists on the
machine.
0: If I sell my snowmobile within the warranty period, will the new owner qualify
for the balance
of the warranty?
A: Yes, provided the unit has already been registered with the manufacturer.
Note that the change
of ownership card in this manual shouldbe completed
and sent to Bombardier Inc.
0: How can I receive the best owner assistance?
A: The satisfaction and goodwill of the owners of Bombardierproducts are of
primary concern to your authorized dealer and Bombardier Inc. Normally, any
problems that arise in connection with the sales transaction
or the operation
of your snowmobile willbe handledby your Dealers Sales or Service Depart-
ments.
It is recognized, however; that despite the best intentions of everyone
concerned, misunderstandings
will sometimes occur. If you have a problem
that has
not been handled to your satisfaction through normal channels, we
suggest that you discuss yourproblem with a member of dealership manage-
ment. Frequently, complaints are the result
of a breakdown in communications
and can quickly be resolved by a member of the dealership management. If
the problem already has been reviewed with the Sales Manager or Service
Manager; contact the Dealer
himself or the General Manager.
7

LISTING OF AREA
DISTRIBUTORS ______________________ __
CANADIAN DISTRIBUTORS
PROVINCE OF QUEBEC
SERVICE OFFICE
BOMBARDIER INC.
Valcourt (Quebec) JOE 2LO
[phone]
SALES OFFICE
BOMBARDIER INC.
1350 Nobel Street
Boucherville (Quebec) J4B
1A1
[phone]
PROVINCE
OF ONTARIO
SERVICE AND SALES OFFICE
BOMBARDIER INC.
230 Bayview Drive
Barrie (Ontario) L4N 5E9
(705)
728-8600
ALTLANTIQUE REGION
SERVICE OFFICE
BOMBARDIER INC.
PO. Box 7060
Riverview (New Brunswick) E1B 1VO
[phone]
SALES OFFICE
BOMBARDIER INC.
1350 Nobel Street
Boucherville (Quebec) J4B 1A1
[phone]
ALBERTA, BRITISH
COLUMBIA, MANITOBA,
SASKATCHEWAN, YUKON
SERVICE AND SALES OFFICE
BROOKS EQUIPMENT LIMITED
1616 King Edward Street
P.O. Box 985
Winnipeg (Manitoba) R3C 2V8
[phone]
NEWFOUNDLAND, LABRADOR
SERVICE AND SALES OFFICE
CHARLES R. BELL LIMITED
Riverside Drive
P.O. Box 1050
Corner Brook (Newfoundland) A2H
6J7
[phone]
NORTH-WEST TERRITORIES,
FRANKLIN DISTRICT & KEEWATIN
SERVICE AND SALES OFFICE
HUDSON'S BAY CO. LIMITED
165 Hymus Blvd
Pointe-Claire (Quebec) H9R
1G2
[phone]
8
AMERICAN DISTRIBUTORS
EAST-CENTRAL, CENTRAL,
WESTERN REGION
SALES OFFICE
BOMBARDIER CORPORATION
7575 Packer Drive
P.O. Box 8035
Wausau, Wisconsin 54402-8035
U.S.A.
(715)
842-8886
EAST-CENTRAL, CENTRAL REGION
SERVICE OFFICE
BOMBARDIER CORPORATION
4505 West Superior Street
P.O. Box 16106
Duluth, Minnesota 55816-0106
U.S.A.
[phone]
WESTERN REGION
SERVICE OFFICE
BOMBARDIER CORPORATION
PO. Box 1569
Idaho Falls, Idaho
83403
U.S.A.
[phone]
EASTERN REG ION
SERVICE AND SALES OFFICE
BOMBARDIER CORPORATION
East Main Street Road
Malone,
New York 12953
U.S.A.
[phone]
ALASKA
SERVICE AND SALES OFFICE
THE BRYANT CORPORATION
NE. 190th & Woodinville
Snohomish Road
P.O. Box 389
Woodinville, Wa 98072
U.S.A.
[phone]

HOW TO IDENTIFY
YOUR SNOWMOBILE _________ _
The main components of your snowmobile (engine, track and frame) are identified
by different serial numbers. It may sometimes become necessary to locate these
numbers for warranty purposes or to trace your snowmobile
in the event of theft.
Engine serial
number
A015 002 019
A015 007 023
Track serial
number
A009 005 002
Vehicle serial number
0
NOTE: We strongly recommend that you take note of all the serial numbers
on your vehicle and supply them to your insurance company. It will surely
help
in the event your snowmobile is stolen.
9

CONTROLS/
INSTRUMENTS ______________________ __
A
R
Q
p
L
0
N------~-------
A015 007 046
A) High Beam Pilot Lamp (blue)
B ) Temperature Gauge
C ) Speedometer
D ) Tachometer*
E ) Electric Fuel Gauge*
F) Injection 0!1 Level Pilot Lamp
(red)
G) Adjustable Steering Handle
H) Emergency Cut-out Switch
I ) Throttle Lever
* Optional for MX/MX LT
A) High Beam Pilot Lamp
(Blue)
Lights up when headlamp is on high
beam.
10 -------------------------
J) Primer
K ) Rewind Starter Handle
L ) Hood Latch
MJ Fuel Tank Cap
N) Ignition/Light Switch
0) Fuel Level Indicator
(MX/MX LT only)
P ) Tether Cut-out Switch
Q ) Brake Lever
R ) Head/amp Dimmer Switch
B) Temperature Gauge
F
G
H
I
The gauge indicates engine coolant tem-
perature. Normal operating temperature
is from 50° to 100°C (120° 212°F).

A015 007 005
However, coolant temperature can vary
according to driving conditions. If coo-
lant temperature exceeds 100°C
F)
reduce speed and run vehicle in roose
snow or stop engine immediately.
+WARNING:
To remove coolant
tank cap, place a cloth over the
cap and unscrew it to the first stop to
release the pressure. If this notice
is
disregarded loss of fluid and severe
burns could occur.
C) Speedometer
The speedometer is linked directly to the
drive axle. Direct-reading dial indicates
the speed
of the vehicle.
Odometer records the total distance trav-
elled
in kilometers.
D) Tachometer
The tachometer registers the impulses
of magneto. Direct-reading dial indica-
tes the number of revolutions per minute
(RPM)
of the engine.
,., CAUTION: The tachometer is pro-
T tected by a fuse, if tachometer
stops operating check fuse condition
and if necessary replace. The fuse
is
0.1 amp. Do not use a higher rated fuse
as this can cause severe damage to
the tachometer.
E) Electric Fuel Level Gauge
The electric fuel gauge is located in the
dashboard and allows driver to observe
the fuel level while riding the snowmo-
bile.
F) Injection Oil Level Pilot
Lamp (Red)
Will light up when injection oil level is
low. Check level and replenish as soon
as possible.
,., CAUTION: Do not run engine out
T of oil. Serious engine damage will
occur.
0 NOTE: Whenever brake lever
is
actuated, oil injection level pilot
lamp should light
up. If not replace lamp.
G) Adjustable Steering Handle
-Remove steering pad.
-Loosen the four (4) retaining screws.
Adjust the handle to the desired
position.
+WARNING: Do not adjust too
high
as the brake lever may contact
the windshield when turning.
Lock the steering handle in place by
tightening the four (4) retaining screws
to
26 N•m (19 lbf•ftl.
Reinstall steering pad.
H) Emergency Cut-out Switch
A push pull type switch located on the
right side
of the handlebar. To stop the
engine
in an emergency, push the but-
ton to the lower
off position and simul-
taneously apply the brakes.
To start en-
gine, button must be at the upper
ON
position.
11

+ON +OFF
~~
position Lower position
starting
to stop engine
A017 006 004
The driver of this vehicle should famil-
iarize himself
with the function of this
device
by using it several times on first
outing. Thereby being mentally prepar-
ed for emergency situations requiring its
use.
..&.. WARNING: Ifthe switch has been
T used in an emergency situation
the source of malfunction should be
determined and corrected before re-
starting engine.
I) Throttle Lever
Located on the right side of handlebar.
When compressed, it controls the engine
speed and the engagement
of the trans-
mission.
When released, engine speed
returns automatically
to idle.
J) Primer
A push-pull button located below hand-
lebar. Pull and push button
{2-3 times)
to activate primer. The primer should
always
be used for cold engine starts.
After engine
is warm however, it is not
necessary to use primer when starting.
K) Rewind Starter Handle
Auto rewind type located on right hand
side
of vehicle. To engage mechanism,
pull handle.
12
L) Hood Latch
Pull down the latches to unlock the hood
from its anchors.
0 NOTE: Always lift hood gently un-
til stopped by restraining device.
..&.. WARNING: It is dangerous to run
T an engine with the hood opened,
unfastened
or removed.
M) Fuel Tank Cap
Unscrew to fill up tank then fully tighten.
..&.. WARNING: Never use an open
T flame to check fuel level.
N) Ignition/Light Switch
The lights are automatically ON when-
ever the engine is running.
OFF
A002 007 002
Key operated, two (2) position switch.
To start the engine, first turn key to ON
position. To stop the engine, turn the
key to OFF position.
0) Fuel Level Indicator
Mounted on left side of fuel tank, it pro-
vides visual indication
of fuel level in
tank.

P) Tether Cut-out Switch
A pull switch located below the handle-
bar. Attach tether cord to wrist or other
convenient location then snap tether cut-
out cap over receptacle before starting
engine.
If emergency engine
~~shut off" is re-
quired completely pull cap from safety
switch and engine power will
be auto-
matically shut
11
0ff".
0 NOTE: The cap must
be installed
on the safety switch at
all times in
order to operate the vehicle.
..A.. WARNING: If the switch is used
T in an emergency situation the
source of malfunction should
be de-
termined
and corrected before restart-
ing engine.
Q) Brake Level
Located on the left side of handlebar.
When compressed, the brake
is applied.
When released, it automatically returns
to its original position. Braking effect
is
proportional to the pressure applied on
the lever and to the type
of terrain and
its snow coverage.
R) Headlamp Dimmer Switch
The dimmer switch, located on left side
of handlebar/ allows correct selection of
headlamp beam.
To obtain high or low
beam simply flick switch.
Tool Bag
To gain access/ tilt hood. Ideal location
for spare spark plugs, rope/ first aid kit,
flashlight, etc.
Spark Plug Holder
To keep spark plugs dry and prevent
shocks that might affect the adjustment
or break them, a holder
is provided un-
der hood, close to top
of right shock
absorber.
Fully tighten them into the holder.
Right
shock absorber
A015 008 007
Spark plugs
in holder
Fuse Holder
Tachometer
The tachometer is protected by a 0.1
ampere rated fuse. Fuse holder is locat-
ed under the hood beside the tachome-
ter. If it stops operating/ check fuse con-
dition and replace if necessary.
13

Spare Drive Belt Holder
A spare drive belt can be installed in
drive belt holder clips on belt guard.
A015 003 008
Spare drive belt
holder clips
Fuel Shut-off Valve
It is recommended to close it when trans-
porting or storing vehicle. The valve
is
under hood/ on top of R.H. side foot-
rest.
Two stoppers are provided on the fuel
shut-off valve to prevent the lever from
rotating due to vibrations.
These stoppers
are set so that the inner
tip ofthe
lever slightly contacts the stop-
pers while in the fully opened or fully
closed positions.
14 ---------------------------
Valve
A015 007 047
R.H.
footrest
Stoppers
When opening or closing valve, always
rotate lever
so that it flips over the stop-
per and maintains its position.
Fully opened ~
A015 008 006
~~\
0 0 Fully closed
R.H.
footrest
Fully open the valve in order to operate
the vehicle.
-.r CAUTION: Always fully open the
T valve before riding. Never allow
the valve lever to remain between stop-
pers.

Rear Bumper
The rear bumper can be installed in two
(2) positions
as desired by the driver.
The low position can
be used in deep
snow to provide grip at a more conve-
nient level.
A015 005 042
AOi5 005 041
To install bumper in lower position, pro-
ceed
as follows:
Lift snow guard and block
in that po-
sition.
From inside tunnel, remove bumper
retaining screws.
Two per side.
-Remove bumper.
Reverse bumper position and insert
in tunnel.
When installing bumper
in lower po-
sition, the retaining screws have to
be relocated to different holes, as
shown.
High bumper
position
......,_IIJH
screw holes
A015 007 024
Location of screws
for bumper
in
low position
Firmly tighten bumper screws.
-Lower snow guard.
0
NOTE: When installing bumper at
upper position, bumper retaining
screws
have to be relocated to different
holes,
as shown.
15

Location of screws
for bumper in .tiii{;;......-'P."""
high position
A015 007 025
Accessories
A complete line of optional accessories
is available for your snowmobile. Con-
tact your authorized
BOMBARDIER dealer
for more information.
Front Grab Handle
Located at the front of the bottom pan,
this grab handle must
be used whenev-
er front
of vehicle is lifted.
1lr CAUTION: Do not use skis to pull
T or lift vehicle.
16

BREAK-IN PERIOD ______ _
Engine
With Bombardier-Rotax snowmobile en-
gines, a break-in period
is required be-
fore running the vehicle at full throttle.
Engine manufacturer's recommendation
is ten {10) to fifteen (15) operating hours.
During this period, maximum throttle
should
not exceed 3/4, however, brief
full acceleration and speed variations
contribute to a good break-in. Continued
wide open throttle accelerations, pro-
longed cruising speeds, and lugging
are
detrimental during the break-in period.
0
NOTE: To assure additional protec-
tion during the initial engine break-
in,
500 ml (18 imp. oz) of BLIZZARD Oil
{ P/N 496 0135 00) or the sa me quanti-
ty of
BOMBARDIER Injection Oil (PIN 496
01 33 00) should be added to gas for
the first full gas tank filling.
,., CAUTION: Remove and clean
T spark plugs after engine break-in.
Belt
A new drive belt requires a break-in pe-
riod
of 25 km (15 miles).
10- Hour Inspection
As with any precision piece of mechan-
ical equipment, we suggest that after the
first ten (10) hours
of operation or thirty
(30} days after the purchase, whichever
comes first, your vehicle be checked
by
your authorized dealer. This inspection
will give you the opportunity to discuss
the unanswered questions you may
have
encountered during the first hours of
operation.
The 10-hour inspection is at the ex-
pense of the vehicle owner.
17

10 - HOUR INSPECTION CHECK LIST
./
Engine timing
Spark plug condition: (remove and clean)
Carburetor
adjustments
Oil injection pump adjustment
Engine head nuts
Drive pulley screw (torque)
Engine
mount screws
Muffler attachment
Chaincase oil level
Drive chain tension
Injection system oil level
Rotary valve oil level
Engine
coolant level
Brake operation and lining
condition
Ski alignment (runners condition), ski leg camber adjustment
Steering arm, retorque to 25 N•m (18 lbf•ft)
Handlebar bolts, retorque to 26 N•m (19 lbf•ft)
Driven pulley preload
Pulley alignment and drive belt condition
Track condition, tension and alignment
Suspension, torque rear axle screw
to 48 N •m (35 lbf•ft)
Lubrication (steering, suspension, drive axle, etc.)
Electrical
wiring
Tighten all loose bolts, nuts and linkage
Operation
of lighting system (HI/ LO beam, brake light, etc.},
test operation of emergency cut-out switch and tether cut-out switch
We recommend that you have your dealer sign this inspection.
Date of 1 0-hour inspection
18