Polaroid PLANC080 User manual

+
-
PLANC080
Active Noise Cancelling
Wireless Headphones
User Guide
Buttons on the Headphones
Have you got everything?
Operation
1. ANC switch
2. Micro USB Port
3. Microphone
Power on and pair with a Bluetooth device
Press and hold the (Function) button on the headphone. The LED status indicator will
ash red/blue, indicating it is ready to pair with a Bluetooth device. Turn your smart phones
Bluetooth and select “PLANC080” on the list of available devices. Once successful, you will
hear a notication sound and the LED status indicator will light up blue. Music from your
smart phone will now be played through the headphones.
• Press the - button to decrease the volume level. Press and hold to play the previous
song.
• Press the +button to increase the volume level. Press and hold to play the next song.
• Press the (Function) button to play/pause the song.
Bluetooth call function
Once successfully connected to your smart phone, you can answer/reject incoming phone
calls. Press the (Function) button to answer in an incoming call. Press and hold the
button to reject the call. Press the (Function) button twice to redial the most
recent phone number.
• Press the - button to decrease the volume level.
• Press the + button to increase the volume level.
AUX mode
Connect a 3.5mm audio cable to the AUX In port of the headphone and the other end to your
audio device. The headphone will automatically switch to AUX mode and power o to save
battery life.
ANC (Active Noise Cancelling Mode)
Slide the ANC switch to turn the headphone into ANC mode. Slide the ANC switch back to
return to normal mode.
NOTE: ANC mode will use more battery than normal mode.
Power o and charging
When the battery is low, an alert tone will be heard and the LED indicator will turn red
indicating it is low battery. Connect the supplied micro USB charging cable to the micro
USB port and the other end of a USB power source. The LED status indicator will light up red
during charging and disappear when fully charged.
Press and hold the (Function) button to power o the headphone, the LED status
indicator will turn o and a voice notication will be heard. If not paired with a Bluetooth
device, it will automatically power o ater 5 minutes.
A. ANC Wireless Headphones
B. 3.5mm Audio Cable
C. Micro USB Charging Cable
D. User Guide
E. Warranty Certicate
1 2 3 4 5 6 7 8
4. AUX In Port
5. LED Status Indicator
6. - Button
7. (Function) Button
8. + Button
Have questions?
We’ve got answers.
Visit us at tempo.org/support or
give us a call at 1300 886 649
Distributed by:
Tempo (Aust) Pty Ltd
PO Box 132,
Frenchs Forest,
NSW 1640
Polaroid, Polaroid Color Spectrum and Polaroid Classic
Border Logo are trademarks of PLR IP Holdings, LLC,
used under license . PLR IP Holdings, LLC does not
manufacture this product or provide any Manufacturer’s
Warranty or support.
©2022 All rights reserved.
Your new product is ready to enjoy!
Well done, you made it.
Now sit back and relax... your new product is automatically covered
by a 1-year warranty. How nice!
E
D

Specications
General Safety Warnings
GENERAL SAFETY WARNINGS
For the safety of yourself and others, follow all instructions and take notice of all the warnings.
When adhered to, these safety precautions can reduce the risk of re, electric shock and injury.
This product complies with Australian Safety standard AS/NZS 62368.1 to ensure the safety of
the product.
The RCM is a visible indication of a product’s compliance with all applicable ACMA
regulatory arrangements, including all technical and record-keeping requirements.
IMPORTANT
Risk of hearing damage: Never place the
headphones on ears BEFORE turning them on,
as the sudden volume may be too high and
could cause hearing damage.
Keep the headphones out of ears until you
have turned down the volume. Test this by
playing the music and holding the headphones
near (but not IN) your ear, as you turn the
volume down.
Once the volume is turned down, you can
place the headphones onto ears and gradually
increase the volume to the desired level.
Plastic wrapping can be a suffocation hazard
for babies and young children, so ensure all
packaging materials are out of their reach.
To prevent environmental factors (dampness,
dust, food, liquid etc.) harming the power
bank, only use it in a well-ventilated, clean and
dry environment, away from excessive heat or
moisture.
Keep the product away from direct sunlight or
heat sources.
In case of damage, do not disassemble,
repair or modify the product yourself. Contact
After Sales Support for advice on repair or
replacement, or refer servicing to qualified
personnel only.
Children should be supervised to ensure they
do not play with the product.
Do not put any object on top of the product.
Do not place or store appliance where it can
fall or be pulled into a bath or sink.
This product is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the product by a person
responsible for their safety.
Do not expose the product to microwaves.
Clean using a dry cloth only - do not use water
or chemicals.
Keep the product away from oils, chemicals or
any other organic liquids.
Use this appliance only for its intended
purpose as described in this guide.
Responsible disposal of the packaging
The packaging of your product has been
selected from environmentally friendly
materials and can usually be recycled. Please
ensure these are disposed of correctly. Plastic
wrapping can be a suffocation hazard for
babies and young children, please ensure
all packaging materials are out of reach and
are safely disposed of. Please recycle these
materials rather than throwing them away.
Responsible disposal of the product
At the end of its working life, do not throw this
product out with your household rubbish. An
environmentally friendly method of disposal
will ensure that valuable raw materials can
be recycled. Electrical and electronic items
contain materials and substances which, if
handled or disposed of incorrectly, could
potentially be hazardous to the environment
and human health.
Ok, time to give us a call
What? You mean the User Guide didn’t have ALL the answers? Speak to us!
We’d love to help you get up and running as quickly as possible. Call our
Ater Sales Support on 1300 886 649.
Operating hours: Monday-Friday, 8:30am-6pm; Saturday, 9am-6pm AEST
Playback time 14 hours*
Charging time 2-2.5 hours
Input 5VDC 1A
Battery 3.7VDC, 400mAh
Dimensions (L) x (D) x (H) 165 x 170 x 80 mm
Weight 200g (net)
325g (gross)
*14 hours of playtime is based on volume no higher than 80% with Active Noise Cancelling o
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth SIG,Inc. and any use of such marks by
Hands (IP) Holdings Pty Ltd is under license. Other trademarks and trade names are those of their respective owners.
Troubleshooting
Cannot hear
audio through
headphones
• Ensure the headphones are paired with your smart phone, the
LED indicator will light up blue.
• Increase the volume.
• Power o your headphones then power them on and pair with
your smart phone again.
Headphone not
charging • Ensure you are connected to a USB power source.
Cannot connect to
Smart Phone
• Ensure the headphone is on before pairing.
• Ensure your smart phone’s Bluetooth®is turned on.
• Please power o the headphone and power on again.