Polk Audio MM6 6.5'' System User manual

Attach your recei
hereand file for fu-ture
reference.I$may
be required f-or
; POLK/MOMO: CHAMPIONSHIP PERFORMANCE

DearMusicLover,
Youhavejustenteredanewrealmofcaraudio!I am
extremelyexcitedaboutthesepolkAudiol~ilOhilO
@,hperformancespeakers;thisisthefirsttimethat
theexdusiveMQMODesignhouseofDalyhasco-
brandedaproduct.We’vepartneredwiththemto
producethebestsounding,bestlookingcarspeakers
ever.Theyaregoingtomakeyourcarlookand
soundgrmt.
TheymaynotlooklikeanyotherPolkAudiospeaker,
butmakenomistake:Theycontainthelatestloudspeakertechnologyandmany
ofourexclusivesoundinnovations!IikeDynamicBalance@forcleansoundandlow
distortion.YXIcanbeassuredofoutstandingperformanceandunmatchedquality,
aswellasanexcitingnewlook.
Pleasetakeamomenttoreadthroughthismanual.ItwillheIyyougetthegreatest
possibleenjoymentfromthesefineinstruments.ifyouhavequestions,orwouldlikemore
informationonbuildingthecaraudiosystemofyourdreams,don’thesitatetocalIour
CustomerServiceDepartmentat(800)377-765from913-1~toGpmEasternStandard.Time,
h4ondaythroughFriday

!iournew Polk speakers employDynamic Balance,atechnologythatcameoutofa joint
researchprojectbetweenPolkAudioandJohnsHopkinsUniversity,Thislaser baging
researchenablesustoviewtheentirevibratingsurfaceofadriverortweeter,allowingusto
observetheresonancesthatdeveloponspeakerconesastheymove.Theseresonancesare
therootcauseoffrequencyresponsedistortions.
Asanx-rayenablesaphysiciantodiscoverthemotcauseofasymptomandtherebypre-
scribetherighttreatmentforacure,thislaserimagingtechniqueallowsPolkengineersto
findtherightcombinationofhigh-techmaterials,geom@+yandconstructiontechniques
totuneouttheoffendingresonances.ThebenefitofDynamicBalanceisthedramatic
improvementinthesoundqualityofourspeakers!whicheverylistenercanappreciate.You
nolongerhavetochoosebetweenexcellentbassandsmooth,clearmidrangeandhighs.
NOWyoucanhaveitall,thankstoDynamicBalancetechnology
; POLK/MQMO: CHAMPIONSHIP PERFORMANCE

Likethewaythesegreatnewspeakerssoundinyourcar?You’lllovethewayPolkAudio
speakerssoundin.l~aulrlivil~gmxn!PolkAudiohasbeenmakingworld.-classlmdspeakers
since1972.Polk’sdedicationtofundamentalresearch.hasresultedinover25patents.
Polkloudspeakershaveearnedthepraiseofaudioexpertstheworldover,garneringdozens
ofawardsforinnovative,high-qualitydesign.Whetheryoudesireaudiophile-qualitysound
foryourhome,carorevenyourmultimediacomputer,Polkloudqeakersdeliver
unmatchedperformanceandv&e.
SeethefulllineofPO&Audioloudspeakersat~pr PolkAudiode&v+.orat
www.po~kaudio.com
i.
:
..- .

@ Futuristic cast aluminum baskets that mimic MOM0 wheel designs
* EIegant matching motor cup conceal5 a beefy magnet structure
e Rugged, highly conductive pro-grade nickel-plated binding posts
e Polymer/mica composite cones
0 Aramid fiber spiders for greater dynamic range
* 6.5” mid/driver features 1.5” voice coil
a Woven carbon-fiber dustcaps
0
Lightweight red fabric dome tweeters for flat response, great inner detail
and low distortion
e Neodymium magnets that are small and powerful
* Low viscosity ferro-magnetic cooling fluid for superior power handling
* Surface and flush-mount swivel cups allow fine tuning af the tweeter angle
for better soundstaging
e Nickel plated terminals
CB Air-core inductor for low distortion
* Mylar capacitors fur cleaner, more transparent highs
a 3 Level tweeter control to fine-tune the tonal balance of your system
@ Midrange Extension switch bypasses the low-pass filter for better driver-to-
tweeter blending when the two components are separated by a great distance
Pkaseinspecteachkx.xkpakerc;t~kd~y.NotifyyourPC@dealerifyounoticeany
damagedormissingitems.Keepthecartonandpackingmaterial.Theywilldothebest
jobofprotectirlgyourspeakersiftheyneedtobetransported.Checkthatyouhavethe
followingparts:
I POLK/MOMO: CHAMPIONSHIP PERFORMANCE

6
2 mid/woofers
2 tweeters
2 crossover networks
2 tweeter fiush mount cups
2 f!ush rrtolant cup clamps
2 tweeter surface msunt cups
2 grilles
8 - #8 screws with WI 6’” allen head
B wscrew clips
2 - W4Philips head screws
Tweeter hook-up wire
Mid/woofer hook-up wire
Registration card
Readthisrmnualtb.oroughlyfirst.Ifyouhaveanydoubtsaboutyourabikytoexecute
anyoftheinstallationsteps,saveyowxlf aIotofgriefandcontactapmfcssioualinstaller
(yourPolkdealerisagoodplacetafindone).
IfyouintendtcdotheinstaHationyours&weassumethatyoupossessmm skillinthe
properuseofhandandpowertools.Nomatterhowmuchinstallationexperienceyouhave,
it’salwaysagoodideato:
e
Read this manual thoroughly before you begin.
es Plan your installatian carefully.
83 Allow enough time to complete ihe install&ion without rushing.
0 Protect your car from unwanted scratches.
* Phillips head screwdriver
0 9/l 5” ailen wrench
0 Flat blade screwdriver or door panel removal tool
0 Electric drill
0 I/4.” and I/8” drill bits
* Reciprocating saw or razor knife
e Magic marker for marking the cutout (new location only)
@ Metal cutting tool (hole saw, if you intend to cut metal
e Metal file
* A supply of solderless connectm-s
@ Safety glasses
* Wire strippers and cutters
-3 Crimping tool

YourPolk/MU&IOSeriescrossovershaveclearlymarkedterminals.Beforem.&ingconnections
betweenyourcrossovers,mid/woofersandtweeters,refertoFigure1,Thewiresprovidedwith
yourPolk/MOM0Systemhaveoneconductorwithawhitestripe.Usethiswireasthepositive
(+>leadandconnectittothepositive(+)tern&Asonyourcrossoversaswell.astotheposi-
tive(+>terminalsofeachspeaker-

~~~~a~~~~ok/ System
lost carshave’speakergrillesthatblendwiththerestofthecar’sinterior.Sometimesit is
difficulttodeterminehowtoremovethesegrillestogainaccesstothespeakerthatyouintend
toreplace.Ifyouhaveoneofthesegrilles,youmaywanttoconsiderusingaprofessional
installer.Onsomecars,thegrillesareheldbyscrewsorspringclips.Thescrewswillbe
obvious,thespringclipswon’t.
oftherearescrem,removethem,puttheminasafespot,,andmove the@lies.‘I’oremove
aclip-ongrille,useyourQ&[e-mail] resists,backoff
and.thinkagain.abouttheprofessjonalinstali.Thecostofoneofthesecansometimesbeless
thm thecostofmwdoorpan&.Somegrillesare&egraipartsoEthedoorpanelandarenot
removable.It11thesecasesyouwillneedtoremovetheentiredoorpaneltogain.accesstothe
speakerlocat.ion.
Thiswillusuallyrequireremovalofdoorhandles!windowmechmisms~andotherpartssuch
asdoorpullsandlockbuttons.
1. Once ysu get the grille off, remove the factory speakers. Save the hardware.
You may be able tu reuse it to mount your new speaker.
2. Cut the supplied driver wire (the heavier gauge of the two sets of wire) in half.
3. Remove the yellow crcxsouer cuver by squeezing the cover at the tabs. Attach
speaker wires to the crossover ‘“wsofer” terminals. Attach the wire with the white
stripe to the positive Ct) terminat screw, and the m-striped wire to the negative (-)
terminal screw.
4. Rolste the driver wire from the crossover location through grommets to the
mid/woofer location.
5. Strip 118” - I/4” (G-6 mm) ~3 plastic insulation fron the cut ends of The driver m&e.
6. Unscrew the binding past thumbnuts on the mid/woofers to fully expose the hole
in the terminal shaft and slip the other end 04 the wire into the holes in the input
terminals. Tighten the thumbnuts finger-tight (do rmt aver-tighten the nuts as you
may strip the threads). Be sure to attach the wire with The white stripe to the pori-
tiue (red) terminai, and the un-striped wire to the negat&fe (black) terminal.
7
I . If the factory speaker had three screw holes, you’ll need to drill additional screw
holes to accsmmodate the four screw pattern of the PoiklMOMO mid/woofer.
8. Using the hardware retained drsm the factory speaker or the screw clips supp/ied
with the PolWMOMU speaker, secure your new speaker ta the car panel.

1.
2.
3.
4.
5.
6.
7.
8.
9.
Cut a hole in the panel (S-7/8 .inch or 148 mm hole for the MM@.
Use the speaker grille as a template for marking the,locations of the
four screw holes.
Drill the’hofes with a l/8’” bit.
Attach the Screw clips to the car panel at the hole locations.
Cut the supplied driver wire (the heavier gauge of the two sets of wire) in half,
Remove the yellow crossover cover by squeezing the cover at the tabs. Attach
speaker wires to the crossover “woofer” terminals. Attach the wire with the white
stripe to the positive (+) terminal screw, and the un-striped wire to the negative (-1
terminal screw.
Route the driver wire from the crossover location through grommets to the
mid/woofer location.
Strip l/8” - l/4” (4-6 mm) of plastic insulation from the cut ends of the driver wire,
Unscrevv the binding post thumbnuts on the mid/woofers to fully expose the hole
in the terminal shaft and slip the other end of the wire into the holes in the input
terminals. Tighten the thumb nuts finger-tight (do not over-tighten the nuts as you
may strip the threads). Be sure to attach the wire with the white stripe to the posi-
tive (red) terminal, and the un-striped wire to the negative (black) terminal.
10. Place the grille over the driver and line up the screw holes with the screw clips on *
the car panel.
11. Secure the speaker@rille assembly to the car panel with the supplied Allen
head screws.
Onein-qortantadvantageofcomponentsystemsistheirability,whenproperlyinstalled,to
improvethesoundstagecreatedbythemusicinyourcar.Thesoundstageisthemusical‘“pic-
A
ture”m&eupoftheinstrumentsandvocalists.ih.edifferenceinthesoundstagewillbedra-
maticdependingonwhereyoumountyourtweekrs, We recommendasimpleexperiment
thatwillhelpyoudecidethebestspotforp+~rtweetersinyourcar.Werearethesteps:
1. Complete the installation of your entire system except for the MM tweeters.
2. Connect the wires provided with your tweeters to the tweeter terminals on your
PolMMOMO crossovers. (See detailed instructions below.}
101 POLK/MOMO: CHAMPIONSHIP PERFBRMANCE

senger compartment, listening for the differe
We recommend using vocals for this test. You will be a,ble to deter
time the best location for your tweeters. The soundstage or image
above the dash and not be localized to the physical loca
tweeters. Both passenger and driver should be able to hear both channels an
stereo image.
11 Using the base of the surface mount cup as a
template, mark the screw hole and drill it using
a l/8 inch drill bit. Mark the wire holes (for the
tweeter wires), drill using the I/4-inch drill bit.
2. Attach the surface mount cup to the panel using
supplied #4 screw.
3. Cut the supplied tweeter wire (the lighter gauge
wire) in half.
4, Strip I/8” - l/4” (4-6 mm) of plastic insulation
from the cut ends of the tweeter wire. Connect
this end of the wire to the tweeter terminals of
the craswwer. Cannect the white-striped wire
strand to the positive (c) terminal of the
crossover tweeter output and the un-striped wire
to the negative (-) tweeter terminal.
:igure 2
5. Route the tweeter wire from the crossover through grommets to the tweeter
location. Push the red and black tweeter wires through the holes in the bottom
of the tweeter cup and though the panel.
6. Slip the male fast-on connector on the red tweeter wire onto the female connec-
tor on the white-striped wire from the crossover and the black tweeter wire to
the un-striped wire (Figure 2). Make sure the clear plastic insulators fully cover
the fast-on connectors otherwise you may short the tweeter leads and possibly
damage your amplifier.
7. Mount the tweeters by gently pushing them into the surface mount cup. Be
careful not to pinch the wires,
8. Once the tweeter is mounted and connected, swivel the tweeter to fine-tune
the soundstage image of the system.

mounting hole. ~,
Mark the center of the spot and cut a hole with the
2-3116~inch hoi?-saw attachment for your power drill.
Go slow. Or you can use a razor knife instead of a drill.
Cut the supplied tweeter wire (the lighter gauge wire)
in half.
Strip l/8” - f/4”’ (4-6 mm} of plastic insulation from the
cut ends uf the.tweeter wire. Connect this end of the
wire to the tweeter terminab of the crossover, Connect
the white-striped wire strand to the positive (+) terminal
of the crossover tweeter output and the unstriped wire
to the negative (-1tweeter terminal.
Route the tweeter wire from the crossover through
grommets location to the tweeter location.
Assemble cup, clamp, and machine screw loosely.
Route the red and black tweeter wires through the holes
in the bottom of the cup.
Slip the male fast-on connector on the red tweeter wire
FiQUre4
Figure 5
onto the female connector on the white-striped wire from the crossover and the *
black tweeter wire to the un-striped wire (Figure 2). Make sure the clear plastic
insulators fully cover the’fast-on connectors otherwise you may short the tweeter
leads and possibly damage your amplifier.
Pressthe assembly into the 2-3116” hofe until the clamp edge is below the mount-
ing surface, then tighten the screw. The cup wiIl cla’mp down to the surface as
the screw is tightened (Figure 3). In the case of a thick mounting surface, the legs
of the clamp can be bent outward by inserting a screwdriver through the four
rectangular holes in the cup while still mounted (Figure 4)
21 PQLKIMQwlO: CHAtvlPIONStlIP PERFQRMAMCE

ExQim.Mg Frequency RBspbnse Using Mid-Range Extensiion
ThePolkAudio/M.OMUCrossoverfeab.ma Mid-Range Extensionopti,on.Y&m placedin
the‘TN”position,thisrebovesthelowpasscrossoverfilterfrom’themitiassdriver,allow-
ingittorunfull-range.Thismaybehelpfulingettingabetter“blend”betweenmid/driver
andtweeterwhentheINOareplacedsomedistan,cefromeachother.
Itworkslikethis:Normallythecrossoverrollsoffthehighfrequencyresponseofthedriver
inasteepslope. But whenagreatdistanceseparatesatweeterfromthedriver(forexample:
thedriverisonthebottomofthedoorpanel,andthetweeterisonthetopofthedoorpanel
ordash)gettingagooddriver-to-tweeterblendmaybedifficult.TheMid-Range Exkmion
featurebypassesthedriver’scrossover,extendingtheresponseofthedrivertobettermeet
thatofthetweeter. Experiment tofindthesettingthatbestsuitsyourins&Hation.

,,.
.: :
Ifitseemsthatthetweeters
andmid/woofers
arenot“blending”orworkingtogether
in
harmony,trychangingthepolarityofboththetweeters by reversmgthepositive and
negative(-$tweeterwiresatthecrossoverReversingtheabsolutephaseofthetweet&may
helptheblendingorintegrationofthesystemcomponents,particularlyifthetweetersand
mid/woofersareondifferentplanes.Inyourcar,thatis,notyourplane.
Tweeter Angle
TheMMtweetersmaybepivotedtogetthebesthighfrequenqresponseandsoundstage.
Generally,pointingthetweeterstowardthelisteningpositionwillyieldthebestresults.But
don’tbeafraidtotryotheranglesUsethepositionthatsoundsbesttoyou.
Pivotthetweetermodulebyapplyingfirmpressureontheedgeofthetweetermodule,
DONOTAPPLYPRESSURETQTHEDOMEITSELF.
14; POLKIMOMO: CHAMPIONSHIP PERFORMANCE

perchannelto.getthebestpossibleperformance.
“safe Limits Of Operation
YourPolkloudspeakersaremadewiththehighestqualitymaterialsforyearsoftrouble-free
performance.However,damagetoloudspeakerscanoccurwhenanamplifier, regardless
of its wattage, ismadetoplayathigherlisteninglevelsthanitspowercancleanlyproduce
(usuallybeyondthe “1 to2o’clock”positiononthevolumecontrol).
Thisresultsinveryhigh levels ofaudibledistortion,originatingintheamplifier,which
addsaharsh,grittysoundtothemusic.Contrarytopopularbelief,aspeakerismorelikely
tobedamagedbytryingtogettoomuchvolumefromalow-poweredamporreceiverthan
fromahigh-poweredone.
If,afterfollowingthehook-updirections,youexperiencedifficulty,pleasedoublecheck
alltire connections.Makesurethatyourelectronicequipmentisoperatingcorrectlyby
hookingupanotherspeakertothespeakeroutput.Forexample,ifyouarenotgetting
soundfromtheleftchannelspeaker,connecttherightchannelspeakertotheleftoutput.
8youstillgetnosoundfromthatside,theproblemisinyouramporsourceelectronics.
Shouldyouisolatetheproblemtothespeaker,contacttheauthorizedPolkAudiodealer
whereyoumadeyourpurchase.AuthorizedPolkAudiodealersarethebestsourcefor
adviceandassistance,
CallPolkAudio’sCustomerServiceDepartmentatl-800-377-7654from9amto6pm,
EasternTime,MondaythroughFriday.Pleasedonothesitatetocal.iusifyouhave
questionsaboutyourspeakersystem.
Visithttp://www+polkaudio.com
POLK AUDIO / MOM0 DESIGN

Sensitivity 87 d3
tlw/l rnj
..~~......,~~~~~~................... l~~~ll‘*.*,, ,.........,....-.. I1,,1.1.1.,....” . . . . . . . . . . ..l....... OX . . . . ..r...n........................ ~ . . . . . . . . . ..I ~ 11.-.,,................, “I* . _ 111.........-....-11..........,.. _ .,,, . . . . . . . . . . . . . . . (,( ,.,,,,,,.,.,,..,,,,,,..,,” .,...,,.._
Magnet Weight 14.4 a?.
.++.**11**.11111--..---. ..11.1........”.......,lrn....~~............ ..................11~”.........
.......l............................................“,,I.....11....I,.,,..1I1...........^,.....II...L.............._............
... ...11.,,...... ,...~1,,,,,,,,.,,.,..,,,,.._,,_
Cutout Dimensions
Driver 5.82”
148.0 mm
Tweeter 2.14”
54.4 mm
Mounting Depth
top mount with grille 2.81’
71.4 mm
Mounting Depth
bottom mount 3.01 n
76.5 mm
Grille Height
~._
0.90”
22.9 mm
GriIle Diameter 7.22’
183.4 mm
,1.....1............................................),....”.1....,.........11...............,......Il....j... l.,lllll..*,lll...~,,ll.lttll,,,,, “., ..1~.~....~~....x........rr.........* . ............................................I..._ *
Crossover Frequency 3500 Hz
Crossover Tweeter & Driver*:
2nd Order
Butterworth
Tweeter Attenuation 0 d3, -3 d3, -6 d3
*Midrange extension switch on crmmver will bypass driver crossover
161 POLK/MOMO: CHAMPIONSHIP PERFORMANCE

,,,,.,,...,,.., ‘I j,.,,..._._..._...,.......... _ . . . . . . ...” ,.r..~..-.,,.....,,......... --- -..........1..111. ,.... --. L111..11111..... ---1...1111>*1.1.-. -.-~...11*~**1.1--- -.. -----...~~~11*~~ ,,,.....,,,,. .,_....,.......,.,,,I _L,,, ...,,. , ,L, ..I.,,
Cm5 493 ym/N
............._.........,.,,.......,I,,,.”,,,.._...,,,,.,,,,_...._,,,,,,,..1,,,,,,...,.......,....,,,,.........,,.........-...I................I.”I,............,,I.,,.,,.................,.,I,...,...,..............,........”
....”..... ............x..,,...,........,,,.......-...........,.^
BL 5.8TM ..I..._-..-..^
..X,,,,,..__,,,,,,,,,,,...,..,,ll,‘<-,,,,...........~..x.......I..x..,....,....,...._.,.,................................,...........~..,....,,......,,..~.,,,................,,,..~.,...,............,,,.....,........,,.........................,.....,,......~.-I.... ........
Sd .0145 m2
.I56 ft”
,,,,__.,,,.)..,,,.,,.......,,...l..~,,,,,___..,,..,,,,,....~.,.,.,,,,,..,,,,,I...._....,..,,..,,,..........__.._... ..______..._._...
.._._____._.____...,.I,.-,,...........ll.,l..l............,....,.,,,..._x . I...X..,,................I_
Mms 19.8g
Winding Width 12.4mm
.488 in.
..,,,_,,,,...,,,,,,..,.,,,....,,,,,.,........,,...,..,,...........,,,,,......,,1.........l........~”....,,,,...,,,.....1,.,. . ...1....--. . --- ..~.................-----. ------- 1............... .......... ......,....,,...-
Xmax (Linear) 3,2 mm
.I26 in,
,,,,,.~~.,~~.)~,~~~.....,~,~~~~~,,..,I‘,.,,,,....................I..._............1,...,L.*.,,_..._..,,_............................._..~.,,,,,,,,,......,,,,._.,,,,...,,,,,,.........,,,,.”,.,,,............,,,...”,........,,........,,.....................,..,,......,........,,.....,,,,...
. _
Xmax (Mechanical) 15.2 mm
,600 in.
,......,”,,,,.,,,,,,.,,,,,,,,,,,,,,,,,,,,..,,,,,...........,,~.........................1..... ..................................”............ ................................~...............I..l....,,.,........1.1,,..1..”.....1..,....11.111...............,,......,,,,......,L...L......_
Le .313 mH
Freq: Fksponk
~l.l,”,,~,~~~,~.~~.~~“l,.l,,.ll.-,,....II,,.....,,...........,.......,.............-,,.................~~...-.-.................-........”,,,...._..,..........,l,......_-.,,,......lll......,..-......au,Irrll-.
I,‘**‘.**,,I...~~~~,~“~~~~~~~~..I..llll..li,m>I.....,,..I.
Resenant Freq. (Fo, Fs)
Qms 9.58
..,.,.).I...,_.,.....,,,,,,”,.l..,,,.,.,.,.,.,.,,...”,,,...,,,.,,,,,,,,,...,..._,,,,,.,,,,,...-.,,,,,‘..,,_,,,... I. . I..~...................~..........................”..-...............”,....1.................1.1~.1...,,..............11,1............ ...lllllr”
Qes
POLK AUDIO / MOM0 DESIGN ;I7

referredtoas“you.”ToallowPolkAudiotoofferthe
bestpossiblewarrantyservice,pleasefihoutthe
Product RegistrationCard(s)andsendthemtothe
r&toryattheaddressprovidedintheRegistration
Cardwithin(lo}tendaysofthedateofpurchase.
DefectiveProductsmustbeshipped,togetherwitha
proofofpurchase,prepaidinsuredtotheAuthorized
PolkAudioDealerfromwhomyoupurchasedthe
Product,ortoPolkAudio,2550BritanniaBlvd.,
SuiteI),SanDiego,CA92154.Productsmustbe
shippedintheoriginalshippingcontainer or its
equiv&$inanycasetheriskoflossordamage
in transitistobeborneby you. If,uponexamination
attheFactoryorPolkAudioAuthorizedDealeritis
determinedthattheunitwasdefectiveinmaterials
orworkmanshipatanytimeduringtheWarranty
period,PolkAudioor the PoIkAudioDealerwill,atits
option,repairorreplacethisProductatnoadditional
charge,exceptilssetforthbelow.Allreplacedparts
andProductsbecomepropertyofPolkAudio.
ProductsreplacedorrepairedunderthisWarranty
willbereFume!dtoyou,withinareasonabletime,
freightprepaid.
InnoeventwillPolkAudio,Inc.be1iabIetoyoufor
anyincidentalorconsequentiai~damagesarisingout
oftheuseorinaMitytousetheProduct,evenifPolk
Audio,Inc.oraPolkAudioDealerhasbeenadvised
ofthepossibiliryofsuchdamages,oranyother
cIaim by any other party.‘somestatesdonotallow
theexclusionorlimitationofconsequent&ldamages,
sotheabovelimitationandexclusionmaynotapply
to you. This Warrantygivesyouspecificlegalrights
whichmayvaryfromstatetostate.
ThiswarrantyappliesonlytoProductspurchasedin
theUnitedStatesofAmerica,itspossessions,andU.S.
andNATO,armedforcesexchangesandaudiaclubs.
TheWarrantytermsandconditionsapplicableto
Productspurchasedinothercountriesareavailable
fromthePolkAudioAuthorizedDistributorsin
suchcountries.