1. Unplug extension cord from the wall outlet first and then remove all ornaments and decorations.
2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove from
section below and fold all branches toward the pole.
3. Continue by gently lifting straight up each section(s) from the section below and fold
all branches toward the pole until the bottom section is removed from the tree stand.
Cover the protective cap on the poles to avoid damaging the internal parts. (See Fig. D)
4. Carefully place all tree sections into shipping box and tape it shut.
5. When not in use, please store your tree in a cool, dry place away from sunlight.
Exposing your tree to excessive heat or humidity may damage your tree.
STORAGE INSTRUCTIONS
For pre-lit trees, if the tree does not illuminate
1. Please check to make sure that all connectors are properly connected and the power adapter / extension cord is
plugged into the wall outlet. (If the tree comes with a foot pedal, try stepping on the on/off button).
2. Turn the poles gently to ensure they are connected into place.
3. Check for loose connection between light string plugs and extension cords.
4. Check for loose, broken or missing bulbs and replace as needed.
Loose Hinge Pin
1. Extra hinge pins are included for repairing the hinges. Place the branch into the slot of the bracket.
2. Insert a new hinge pin through the hole and secure using the retainer washer. (See Fig. E)
TROUBLE SHOOTING TIPS
Each tree includes hinge pins/washers and spare bulbs. If extra parts are
needed, please contact our customer service center.
SPARE PARTS
Press the selector button on the “Dual Color Light Controller”to select
among:
(1) WARM WHITE AND MULTI-COLOR ALTERNATING;
(2) WARM WHITE LIGHTS;
(3) MULTI-COLOR LIGHTS;
(4) TURN OFF ALL LIGHTS.
1. Use only power adapter supplied with this product, using a different adapter can damage the lights and cause fire
or electrical shock hazards.
2. FOR INDOOR USE ONLY.
HOW TO USE THE DUAL COLOR LIGHT CONTROLLER:
3. Each tree section is numbered with a tag. Please identify all sections before assembling.
4. Assemble the tree from the bottom to the top. Start with the bottom section and remove protective cap before
inserting into the assembled stand. Make sure the pole is firmly inserted and secured into the stand. (See Fig. B )
5. Open the protective cap from the lower section(s) and continue inserting the upper section(s) until the tree top is
inserted.
6. Allow branches to fall into place or gently pull up and out. When adjusting branches, be sure that all wires are free
of branch hinges.
7. Plug the extension cord into a wall outlet, your entire tree should now be lit. (See Fig. B ) If some bulbs do not light
or are flickering, search for any loose plugs and/or broken, loose or missing bulbs. Replace the bad bulbs promptly
in order to maintain the performance and life expectancy of your pre-lit tree.
8. Begin to shape the branches and tips working from the bottom to the top. Start with tips farthest from the pole and
fan out one to the right, one to the left and one at the center of the main stem (See Fig. C). This is a Perfect Shape.
tree, just slightly upsweep all branch tips for a uniform look, shift branches to fill any gaps. Your tree is now com-
plete and ready to be decorated.
Top view Side view
Fig. C
Fig. D
Fig. E
Light
Control Box
Color Selector
Button
WARNING
Page: 2 / 4 Page: 3 / 4
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed, including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use seasonal products outdoors unless marked “suitable for indoor and outdoor use.” When product is used
outdoors, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a
qualified electrican for proper installation.
c. This seasonal product is not intended for permanent installation or use.
d. Do not mount or place the product near gas or electric heaters, fireplaces, candle, or other similar sources of heat.
e. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f. Do not let bulbs rest on the supply cord or on any wires.
g. Unplug the product when leaving the house, when retiring for the night, or if it is left unattended.
h. This is an electric product and not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not
be played with or placed where small children can reach it.
i. Do not use this product for anything other than its intended use.
j. Do not hang ornaments or other objects from cord, wire or light string.
k. Do not close doors or windows on the product or extensions cords, as this may damage the wire insulation.
l. Do not cover the product with cloth, paper or any material that is not a part of the product when in use.
m. This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric
shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be fully
inserted. Do not alter or replace the plug.
n. This product is equipped with push-in type bulbs. Do not twist bulbs.
o. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the
fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be
attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper
fuse rating) and check the product.
p. Read and follow all instructions that are on the product or provided with the product.
q. SAVE THESE INSTRUCTIONS.
USE AND CARE INSTRUCTIONS
1. Before using or reusing, inspect product carefully. Discard any products that have cut, damaged or frayed wire
insulation or cords, cracks in the bulb holders or enclosures, loose connections or exposed copper wire.
2. Before disassembling the tree, unplug the tree and remove all ornaments and decorations.
3. Gently lift the tree top straight up to remove it from the centre section and fold all branches toward the pole.
4. Repeat this step for the centre and bottom tree sections.
5. When storing the product, carefully remove the product from wherever it is placed, including on trees, branches or
bushes, to avoid any undue strain or stress on the product conductors, connections and wires.
6. When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICING INSTRUCTIONS
Fuse replacement:
a. Grasp plug and remove from the receptacle or other outlet device. Do not
unplug by pulling on cord.
b. Open fuse cover. Slide open fuse access cover on top of attachment plug
toward blades.
c. Remove fuse carefully.
d. Risk of fire. Replace fuse only with 5 A, 125 V fuse for the power cord set.
e. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
f. Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that
should not be removed. Discard product if the attachment plug is damaged.
SPARE FUSE
