Pool Frog XL PRO User manual

1
POOL FROG®XL PRO®
Instruction Manual
Mineral Pool-Care Cyclers
for Pools up to 40,000 Gallons
Customer Service 800-222-0169
frogproducts.com
POOL FROG XL Pro comes with the
POOL FROG Mineral Reservoir
Patented Mineral Disinfectant
®
Cleaner
because it kills bacteria two ways
Clearer
because it helps keep pH in range
Softer
because it reduces chlorine use up to 50%*
Easier
with pre-lled pacs for no mess,
no guess and no stress
To minimize the risk of serious injury, death or
damage, before installing or first using this
equipment, read Instruction Manual and all safety
labels and follow all safety instructions and
precautions. Save manual for future reference.
WARNING
Ver la versión en español de este manual en frogproducts.com/product/pool-frog-xl-pro

2
TABLE OF CONTENTS
POOL FROG XL Pro Introduction 3
Notes and Safety Information 4
Safety Labels on Cyclers 5
Installation Tips to Ensure Proper Performance 6
In-Line Installation 7
Step 1: Preparing the Pool 8
Step 2: Putting the System to Work 9
Step 3: Setting the Cyclers Control Dials 10
Step 4: Routine Pool Care 11
Replacing POOL FROG Mineral Reservoir 12
Using FROG BAM®13
Using POOL FROG Pac 14-15
Winterizing 15
Troubleshooting 16
Parts List 17
Maintenance - Replacing Control Dial O-Rings 18
Maintenance - Replacing Cap O-Rings and Knobs 19
Warranty 20
For information on King Technology’s entire product
line, visit our website at frogproducts.com

3
Welcome to easier pool care courtesy of POOL
FROG XL Pro. With POOL FROG XL Pro, your pool
water will look and feel better without a lot of
work or a lot of chlorine. This system†controls
bacteria using a combination of minerals and
reduced chlorine levels-up to 50%* less.
Part 1
POOL FROG XL Pro Cyclers
The water treatment center that controls the ow of water to
each part of the POOL FROG XL Pro System.
Part 2
POOL FROG Mineral Reservoir
Holds the minerals and ts inside the POOL FROG XL Pro
Mineral Cycler. Product # 01-12-5462
POOL FROG XL Pro
Mineral Cycler
For Pools up to
40,000 gallons.
Product #01-01-5450
POOL FROG XL Pro
Chlorine Cycler
Part 3
FROG BAM
Use with the POOL FROG XL Pro
Mineral Cycler for a 90-day Algae-
Protection Guarantee. One bottle is
good for 15,000 gallons.
Product # 01-10-5060
Part 4
POOL FROGPac
Pre-lled with chlorine tablets and ts
inside the POOL FROG XL Pro Chlorine
Cycler.
Product # 01-03-5613
THE POOL FROG
MINERAL RESERVOIR
MUST BE REPLACED
EVERY SIX MONTHS
OR AFTER ONE POOL
SEASON WHICHEVER
IS SHORTER.
POOL FROG Mineral Reservoir comes inside POOL FROG XL Pro Mineral Cycler and is also sold separately.
POOL FROG Pac and FROG BAM sold separately.
†POOL FROG Mineral System consists of the FROG minerals silver chloride and carbonate used in conjunction with 0.5 ppm chlorine. The POOL FROG Mineral
Reservoir must be used in conjunction with the POOL FROG Pac (EPA Reg. No.: 53735-2), an EPA registered chlorine pool product or a chlorine delivery device.
*Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stabilized swimming pool.
There are 4 parts to the POOL FROG XL Pro
System:
1. POOL FROG XL PRO Cyclers
2. POOL FROG Mineral Reservoir
3. FROG BAM 90-day Algae-Preventative
4. POOL FROG Pac

4
General Notes
These instructions contain information for the safe and proper
operation of these Cyclers. Observe the following principles:
• Ensure that everyone using these Cyclers follows the
instructions and safety precautions.
• Keep the instructions nearby and available for reference
throughout the service life of these Cyclers.
Explanation of the safety pictographs
The following pictographs illustrate the type of hazard.
Pictograph Type of Danger
Safety Alert/General Hazard
Explosion Risk
Hazardous Pressure
Flammable Fire Hazard
Identication of warnings
Warnings are intended to help you recognize risks and avoid
death, injury or property damage. This is how warnings are identied:
Signal Word
Pictographs
Description of danger.
Consequences if ignored.
a The arrow signals a safety precaution to be taken to
eliminate or reduce the risk.
These instructions do not provide for every possible contingency
that might be encountered in connection with installation, opera-
tion or maintenance of this equipment. Should further informa-
tion be desired or should particular issues arise which are not
covered sufciently in this manual, contact King Technology at
800-222-0169.
Explanation of the signal words
Signal words, which depict the probability and severity of harm, are used in these instructions. They are dened as follows:
Notes and Safety Information
Signal Word Meaning
DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death, serious injury
or major property damage.
WARNING Indicates a hazardous situation which, if not avoided, could result in serious injury, death, or major
property damage.
NOTICE Indicates special instructions that are important but not related to physical injury hazards.

5
Fire, explosion and high pressure hazards
To minimize the risk of serious injury, death or property damage while using the POOL FROG XL Pro Cyclers:
a Read, understand and follow all instructions and safety precautions in the manual, and on this Cycler and on any label for
chemicals used with these Cyclers including POOL FROG Pacs, POOL FROG Mineral Reservoir and FROG BAM Algae Preventative.
DANGER
a Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the POOL FROG XL Pro Cyclers.
a Never mix Trichlor chlorine tablets with Calcium Hypochlorite, or with any other form of concentrated chlorine or other chemicals.
a Never add any other types of chlorine, pH adjusters, shock treatments or algaecides through the skimmer.
These products should be added directly into the pool if required.
a Do not contaminate the POOL FROG XL Pro Cyclers, POOL FROG Mineral Reservoir, POOL FROG Pac or FROG BAM with dirt,
organic matter, pool chemicals (such as calcium hypochlorite or pool shocks), fertilizers or other household chemicals. Contact
between any of these substances and the POOL FROG XL Pro Cyclers, POOL FROG Mineral Reservoir, POOL FROG Pac or
FROG BAM, will result in a chemical reaction with the generation of heat, liberation of hazardous gasses and re or explosion.
WARNING
a Use only POOL FROG Pacs, POOL FROG Mineral Reservoir, and FROG BAM in the POOL FROG XL Pro Cyclers. Never use bulk chemicals.
a To prevent the build up of gas pressure in the POOL FROG XL Pro Cyclers, be sure the pool return line valves are open –
except when opening or servicing the unit.
a Do not inhale fumes from the POOL FROG XL Pro Cyclers or POOL FROG Pacs.
a Avoid sparks, smoking, or any open ame near POOL FROG XL Pro Cyclers or chemicals.
a Do not exceed maximum operating pressure of 50 psi or maximum temperature of 104ºF.
a Do not remove the cap while under pressure. Always turn off pump and bleed off pressure before opening POOL FROG XL Pro Cyclers.
a Do not install automatic or fast shut off valves downstream of POOL FROG XL Pro Cyclers.
a Always install the POOL FROG XL Pro Cyclers AFTER a heater (if applicable) on the return line.
a Always install any additional sanitizing equipment AFTER and NEVER BEFORE the POOL FROG XL Pro Cyclers are installed on the return line.
a Do not permit children to use or climb on this product. This product must be positioned to prevent children from using it as a
means of access to the pool.
a Always stand clear of the POOL FROG XL Pro Cyclers during pump start-up.
a Replace POOL FROG XL Pro Cyclers if you see signs of cracks, damage or degradation to the Cycler bodies or caps.
NOTICE
a Prior to pressurizing, check with your dealer to ensure your plumbing connections meet building codes.
a Failure to properly winterize your POOL FROG XL Pro Cyclers could result in freeze damage. (See page 15 for winterizing details.)
Review this label before installing or operating these Cyclers. Contact King Technology at 800-222-0169 if this label is missing
from your POOL FROG XL PRO Cyclers.
Safety Label on the POOL FROG XL Pro Cyclers

6
POOL FROG
XL PRO CYCLERS
A. With High Flow Rate (greater than 80 gpm)
Install T-ttings exactly as shown.
Installation Tips to Ensure Proper Performance
C. Pool and Spillover Spa Combination
B. With In-Floor Cleaner - TWO OPTIONS
✙
✙
✙
✙
✙
Flow
Flow
The best option is to have two lines. One line with pump, lter, heater and
POOL FROG XL Pro Cyclers and a second line with a separate pump for the
in-oor cleaning system (lter optional).
OPTION 1- A Two-Line Installation
OPTION 2 - A 3-Way Valve Installation
POOL WATER LEVEL
POOL RETURN
3-way manual valve or 3-way motor valve plus controls
POOL FROG
XL PRO CYCLERS
POOL FROG
XL PRO CYCLERS
IN-FLOOR
CLEANER
VALVE
IN-FLOOR
CLEANER
VALVE
FILTER
FILTER
FILTER HEATER
PUMP
PUMP
PUMP
Line 1
Line 2
WARNING
• Do not exceed maximum operating pressure of 50 psi.
• Do not install automatic or fast shut off valves
downstream of Cyclers.
• Always install the POOL FROG XL Pro Cyclers AFTER
the heater (if applicable) on the return line.
• Always install any additional sanitizing equipment
AFTER and NEVER BEFORE the POOL FROG XL Pro
Cyclers are installed on the return line.
1) If using a multi-speed pump, run pump for at least
6 hours per day at high speed (at least 40 gpm).
If the pump will run on low speed 24
hours per day or less than 6 hours
per day on high speed, you must
bleed the air while the pump is on by
unscrewing both Cycler cap knobs
until water appears from both Cyclers.
Then screw the knob back on. Repeat
this process each time the cap is
removed for any reason.
2) Install Cyclers with 4-8 psi back pressure.
Lower back pressures could result in under
chlorination. Change the eyeball ttings in
the return jets to a smaller size to increase
back pressure. Contact King Technology at
800-222-0169 for a specially designed Cycler
pressure gauge to determine back pressure
at pool start-up.
3) Special installation Requirements:
IMPORTANT: Over chlorination or damage to the POOL
FROG XL Pro Cyclers or other equipment could result
if special installations A, B or C are not used in these
situations.
•If water ow is higher than 80 gallons per minute (gpm),
see diagram A.
•If an in-oor cleaner is included with pool,
see diagram B, with two options. Preferred
installation is Option 1 with two separate lines.
•If set-up is a pool and spa combination with
common equipment, see diagram C.
Questions? Call Customer Service at 800-222-0169
Monday thru Friday, 8 am to 5 pm central standard time.
Before installing, read all directions carefully and contact your dealer for installation support

7
®
BRAND
PAC 540C
®
BRAND
SECURE CYCLERS
W
a
t
e
r
C
Y
C
L
E
R
M
e
t
e
r
e
d
P
o
o
l
P
u
r
i
f
i
e
r
For better stability, POOL
FROG XL Pro Cyclers may
be mounted on a treated
wood base using Phillips
pan head screws, one in
front and one in back of
each Cycler. If you have
questions about stability,
please contact your dealer
or King Technology.
P
r
i
m
e
r
P
V
C
C
e
m
e
n
t
In-line Installation For pools 7,000 to 40,000 gallons
Do NOT install
POOL FROG XL Pro
Cyclers off-line.
Following Primer directions, brush Primer on the inside of
the adapters and to ends of pipe. Repeat this process with
PVC cement following manufacturer’s directions on that
product.
Measure the distance between
outside adapters and cut out a
section of pipe 3” less than that
dimension.
Allow a minimum of 12” above and on each
side of POOL FROG XL Pro Cyclers to ensure
room for easy replacement of POOL FROG
Mineral Reservoir and POOL FROG Pac.
Insert PVC pipe into adapters
with a twisting action. Hold in
place 5 to 10 seconds to bond.
To prevent damage to heaters or lters, install a corrosion
resistant check valve which will reduce the backow of
chlorine gas when the Cyclers are turned off.
1.
3. 4.
Install with water owing
through the minerals
rst and then the
chlorine.
2.
P
r
i
m
e
r
Minerals Chlorine
TOOLS NEEDED
Hacksaw
MATERIALS NEEDED
Tape
Measure
Primer and PVC
Cement
P
V
C
e
m
e
n
t
Do NOT install in copper pipe if
using POOL FROG Pac as chemical
corrosion may lead to pipe failure.
The POOL FROG XL Pro Cyclers should always be
installed between the lter and pool (or between heater
and pool if applicable). Never install POOL FROG XL Pro
Cyclers before the heater or damage to the heater could
occur.
Install
Measure

8
Step 1: Preparing the Pool
Make sure the pool has adequate
circulation. The total volume of pool
water must completely circulate
through the pump and lter at least
1 to 2 times per day. This usually
requires 8 to 12 hours of circulation.
Check with your dealer for the
proper circulation time for your pool.
Water Balance Guidelines
pH: 7.2 – 7.8
Total Alkalinity: 80 – 120 ppm
Calcium Hardness: 200 – 400
Total Dissolved Solids: <1500
Stabilizer: 20 – 80 ppm
Free Chlorine: 0.5 – 1.0 ppm
Check the pool’s lter gauge often
and periodically clean lter per
the manufacturer’s directions.
A dirty lter will slow the ow of
water which could hamper proper
circulation.
Check the Water Hardness of your ll water before
adding to the pool. If calcium content is higher than
400 ppm, nd a soft water source to ll your pool
instead; otherwise water balance will be very difcult.
Check for metals in the pool such as iron or copper.
Before attempting water balance, these should
be removed. See your dealer for a metal out or
sequesterant and follow the label directions carefully.
Before beginning with any pool care program, you must
rst balance your pool water. Take a water sample to
your local pool professional (or use a complete test kit)
to test for the important Water Balance Guidelines.
IMPORTANT: Always follow printed instructions on
the balancing chemical packages. Add balancing
chemicals in small increments one at a time with
circulation running. For best results, wait 8-12
hours before testing again and adding any additional
balancing chemicals.
WARNING
Do not exceed maximum operating pressure of
50 psi.
Initially shock the pool with a chlorine shock only to
rid the water of contaminants and establish a chlorine
residual. Always follow the manufacturer’s directions
carefully. See the DANGER box below for important
guidance on shocking.
6.
DANGER
• Never add any other types of chlorine, pH adjusters,
shock treatments or algaecides through the skimmer.
These products should be added directly into the
pool if required.
• Never use fast dissolving chlorine tablets, liquid
bleach, or calcium hypochlorite in the POOL FROG
XL Pro Cyclers.
1.
2.
5.
5b. Look at the Total Alkalinity reading rst. Adjustments
should be made to bring the Total Alkalinity in the range of
80 – 120 ppm prior to making any adjustments to pH even
if it throws pH off further.
5c. After Total Alkalinity is in range, test for pH. It should
be between 7.2 and 7.8. If higher or lower, add a pH
adjuster.
5d. Then test your Water Hardness again. If lower than
200 ppm, add Calcium Increaser. Always maintain 200-400
ppm.
5e. Lastly, test for stabilizer or conditioner levels. Add
conditioner if the level is below 20 ppm. This will prevent
chlorine burn off. If stabilizer level is above 80 ppm,
partially drain water and re-ll.
5a. Take a water sample
from the pool and dip a
FROG Test Strip into it.
For best results in achieving water balance, follow
steps 5a through 5e in order.
Dip
u
6.2 6.8 7.2 7.8 8.4
LOW
BAJO
VERY LOW
MUY BAJO
HIGH
ALTO
LOW
BAJO
VERY LOW
MUY BAJO
HIGH
ALTO
VERY HIGH
MUY ALTO
040 80 120 180 240
Total Alkalinity
(ppm)
Alcalinidad Total
(mg/L)
Hold level for
15 Seconds
NOTE: Low pH readings may result when Total Alkalinity is below 80 ppm.
Important: Keep cap on tight between uses. Store at room temperature.
www.KingTechnology.com
Patent 6,030,842 Made in USA 553101443N
Read
v
w
IDEAL
USE BY DATE ON BOTTLE
USE ANTES FECHA
SmartChlor
Out Indicator
Active Chlorine
pH
If lighter color,
check Smart
Chlor catridge
If darker
color, OK
If lighter color,
turn cartridge
setting up
1 number
If darker color,
turn cartridge
setting down
1 number
Just Dip and Read
Test Strips
From
Specially made
for use with
FROG
Mineral Systems
50 100 250 450 800
Calcium
Hardness
Hot Tub
IDEAL
IDEAL
Dip
u
6.2 6.8 7.2 7.8 8.4
LOW
BAJO
VERY LOW
MUY BAJO
HIGH
ALTO
LOW
BAJO
VERY LOW
MUY BAJO
HIGH
ALTO
VERY HIGH
MUY ALTO
040 80 120 180 240
Total Alkalinity
(ppm)
Alcalinidad Total
(mg/L)
Hold level for
15 Seconds
NOTE: Low pH readings may result when Total Alkalinity is below 80 ppm.
Important: Keep cap on tight between uses. Store at room temperature.
www.KingTechnology.com
Patent 6,030,842 Made in USA 553101443N
Read
v
w
IDEAL
USE BY DATE ON BOTTLE
USE ANTES FECHA
SmartChlor
Out Indicator
Active Chlorine
pH
If lighter color,
check Smart
Chlor catridge
If darker
color, OK
If lighter color,
turn cartridge
setting up
1 number
If darker color,
turn cartridge
setting down
1 number
Just Dip and Read
Test Strips
From
Specially made
for use with
FROG
Mineral Systems
50 100 250 450 800
Calcium
Hardness
Hot Tub
IDEAL
IDEAL
3.
4.

9
®
BRAND
4.
Install a POOL FROG
Mineral Reservoir into the
POOL FROG XL Pro Mineral
Cycler. (See page 12 for
directions.)
IMPORTANT:
Replace the POOL FROG
Mineral Reservoir every
6 months or after one
pool season, whichever is
shorter. After that time, you
will hear the spent media
inside, however it is no
longer effective and must
be replaced.
POOL FROG XL Pro
Mineral Cycler
POOL FROG XL Pro
Chlorine Cycler
POOL FROG
Mineral
Reservoir
POOL FROG XL Pro
Mineral Cycler
POOL FROG XL Pro
Chlorine Cycler
POOL FROG XL Pro
Mineral Cycler
POOL FROG XL Pro
Chlorine Cycler
FROG
BAM
When chlorine
reading is down to 1.0
ppm (which may take
a few days) insert a
POOL FROG Pac into
the POOL FROG XL
Pro Chlorine Cycler.
(See pages14-15 for
directions.)
Insert FROG BAM into
POOL FROG Mineral
Reservoir in POOL
FROG XL Pro Mineral
Cycler. (See page 13 for
directions.)
Replace cap and run POOL
FROG XL Pro Mineral
Cycler, with POOL FROG
Mineral Reservoir inserted,
for 10 minutes on Setting
MAXIMUM.
3.
®
BRAND
PAC 540C
POOL FROG Pac
Step 2: Putting the System to Work
1.
2.
Use FROG BAM
for a 90-day
Algae Protection
Guarantee!
Operate

10
For the rst week test the pool water daily
for free chlorine with FROG Test Strips to
ensure correct dial setting. Continue to test
weekly throughout the season.
Use the handle end of cap tool
if the dial is hard to turn.
Step 3: Setting the Cycler Control Dials
These Cyclers are designed to work effectively with a variety of pool equipment as long as the following basic procedures are followed.
1a. Set POOL FROG XL Pro Mineral Cycler control dial to Setting 10. No further adjustments are needed.
1b. Set POOL FROG XL Pro Chlorine Cycler control dial by matching up the parameters of your pool on the chart below. THIS IS
A STARTING POINT ONLY and may need to be adjusted to t your individual pool needs. See #2 below for adjusting directions.
IMPORTANT: If using a multi-speed pump, pump-run times of at least 6 hours per day at high speed are recommended for proper
performance.
If running the pump at low speed only or on high speed less than 6 hours, please follow the 24 hour low-speed directions below.
1.
24 HOUR, LOW SPEED, PUMP-RUN TIME
In order to ensure proper performance when running the
pump on low speed for 24 hours per day or high speed less
than 6 hours per day, bleed the air while the pump is on by
unscrewing BOTH Cycler cap knobs until water appears from
both Cyclers. Then screw the knobs back on. Repeat this
process each time the caps are removed for any reason. Set
the control dial on the POOL FROG XL Pro Chlorine Cycler to 6
and follow the adjustment directions below to determine the
correct setting for your pool.
2.
After each testing, adjust the dial up
by 1/2 increment if the free chlorine
reading has dropped below 0.5 ppm
or adjust down by 1/2 increment if
the reading has risen above 1.0 ppm.
Continue this process each day until
the free chlorine reading stabilizes to
at least 0.5 ppm.
Remember to adjust dial by 1/2 increments only in order to
prevent over chlorination which may bleach pool surfaces.
If using another means of
chlorine support, set dial on
the POOL FROG XL Pro Mineral
Cycler to Maximum. Leave the
POOL FROG XL Pro Chlorine
Cycler empty. Maintain a
minimum chlorine reading of
0.5 ppm with a chlorine delivery
device or hand feeding.
Find your starting dial setting by matching up the parameters of your
pool on the above chart. An In ground pool with approximately 18,000
gallons with a 1 horse power pump running 6 hours a day at high
speed would require a starting dial setting of 4.5.
SINGLE-SPEED PUMP OR HIGH-SPEED PUMP RUN TIME
POOL SIZE
Gallons
6 HOUR PUMP RUN TIME
12 HOUR PUMP RUN TIME
24 HOUR PUMP RUN TIME
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
7,000 3.5 3.0 2.5 2.5^ 2.5 2.0 3.5^ 3.0^ 1.0 3.0^ 2.5^ 2.0^
9,000 4.0 3.5 3.0 2.5 3.0 2.5 2.0 3.5^ 2.0 3.5^ 3.0^ 2.5^
12,000 4.5 4.0 3.5 3.0 3.5 3.0 2.5 2.0 2.5 2.0 1.0 3.0^
18,000 NR 4.5 4.0 3.5 4.5 3.5 3.0 2.5 3.0 2.5 2.0 1.5
25,000 NR NR 4.5 3.5 NR 4.5 3.5 3.0 3.5 3.0 2.5 2.0
30,000 NR NR 5.5 4.5 NR 5.0 4.5 3.5 4.0 3.5 3.0 2.5
35,000 NR NR 6.5 5.5 NR 6.0 5.0 4.5 5.0 4.0 3.5 3.0
40,000 NR NR NR 6.5 NR NR 6.0 5.0 6.0 5.0 4.0 3.5
POOL SIZE
Gallons
6 HOUR PUMP RUN TIME
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
7,000 3.5 3.0 2.5 2.5^
9,000 4.0 3.5 3.0 2.5
12,000 4.5 4.0 3.5 3.0
18,000 NR 4.5 4.0 3.5
25,000 NR NR 4.5 3.5
30,000 NR NR 5.5 4.5
35,000 NR NR 6.5 5.5
40,000 NR NR NR 6.5
^ – Bypass installation recommended. See “Installation Tips” on page 6. NR – This pump size is not recommended for this size pool.
EXAMPLE
IMPORTANT: Control dial settings in excess of these
recommendations could result in excess trichlor levels being
discharged into the pool. This can result in bleaching or
discoloration of areas around the pool inlet or in some cases
bleaching or discoloration of the entire pool liner or paint. In
addition, excess trichlor in the pool can create health hazards
to bathers.

11
SINGLE-SPEED PUMP OR HIGH-SPEED PUMP RUN TIME
POOL SIZE
Gallons
6 HOUR PUMP RUN TIME
12 HOUR PUMP RUN TIME
24 HOUR PUMP RUN TIME
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
7,000 3.5 3.0 2.5 2.5^ 2.5 2.0 3.5^ 3.0^ 1.0 3.0^ 2.5^ 2.0^
9,000 4.0 3.5 3.0 2.5 3.0 2.5 2.0 3.5^ 2.0 3.5^ 3.0^ 2.5^
12,000 4.5 4.0 3.5 3.0 3.5 3.0 2.5 2.0 2.5 2.0 1.0 3.0^
18,000 NR 4.5 4.0 3.5 4.5 3.5 3.0 2.5 3.0 2.5 2.0 1.5
25,000 NR NR 4.5 3.5 NR 4.5 3.5 3.0 3.5 3.0 2.5 2.0
30,000 NR NR 5.5 4.5 NR 5.0 4.5 3.5 4.0 3.5 3.0 2.5
35,000 NR NR 6.5 5.5 NR 6.0 5.0 4.5 5.0 4.0 3.5 3.0
40,000 NR NR NR 6.5 NR NR 6.0 5.0 6.0 5.0 4.0 3.5
Step 4: Routine Pool Care
4.
6. Remember to replace POOL FROG
Mineral Reservoir and all other
POOL FROG replacements as
directed.
Shock the pool every other week or
as needed. We recommend a non-
chlorine shock as reducing chlorine
use is the goal of FROG products.
However, using a chlorine shock is
OK too.
5. Before closing the pool for winter,
use FROG BAM following the
directions on page 13.
Run ltration Cycler enough hours to
circulate all water 1 to 2 times per
day. More than that could result in
over chlorination.
2.
3.
1.
Maintain 0.5 to 1.0 ppm free
chlorine level at all times.
Note: These lower chlorine levels
are only acceptable when using
FROG minerals.
Regularly test water with FROG Test
Strips to maintain pH and Total
Alkalinity.
NOTE: Water balance is affected
by bather load, chemical usage,
evaporation and the makeup of
source water, so maintaining water
balance regularly is important.
WARNING
To prevent the build up of gas pressure in the POOL FROG
XL Pro Cyclers, be sure the pool return line valves are open
–except when opening or servicing the unit.
DANGER
• Never add any other types of chlorine, pH adjusters,
shock treatments or algaecides through the skimmer.
These products should be added directly into the
pool if required.
• Never use fast dissolving chlorine tablets, liquid
bleach, or calcium hypochlorite in the POOL FROG
XL Pro Cyclers.
DANGER
Do not contaminate the POOL FROG XL Pro Cyclers,
POOL FROG Mineral Reservoir, POOL FROG Pac or FROG
BAM with dirt, organic matter, pool chemicals (such as
calcium hypochlorite or pool shocks), fertilizers or other
household chemicals. Contact between any of these
substances and the POOL FROG XL Pro Cyclers, POOL
FROG Mineral Reservoir, POOL FROG Pac or FROG BAM,
will result in a chemical reaction with the generation
of heat, liberation of hazardous gasses and re or
explosion.
Operate
®
BRAN D
PAC 540C

12
Turn off pump. Turn dial to
Setting 0 on the POOL FROG XL
Pro Mineral Cycler. This reduces
the ow of water into the unit
when the cap is open.
Open POOL FROG XL Pro
Mineral Cycler cap. Use the
Cycler cap tool included with
POOL FROG XL Pro to loosen
cap on POOL FROG XL Pro
Mineral Cycler by hitting the
handle with the at of your
hand counter clockwise.
Replacing a POOL FROG Mineral Reservoir
Must be replaced every 6 months or after one pool season.
1.
Check the top of the box and back label of product to make sure
you have the correct POOL FROG Mineral Reservoir to t your
POOL FROG XL Pro Mineral Cycler.
IMPORTANT: The POOL FROG Mineral Reservoir must be
replaced every 6 months or after one pool season whichever
is shorter.
IMPORTANT: Remove and read the
information card.
Please note: Complete instructions for
inserting a POOL FROG Mineral Reservoir,
FROG BAM and POOL FROG Pac are
included inside the POOL FROG Mineral
Reservoir
2.
3.
4.
Find slot on side of
POOL FROG Mineral
Reservoir and line
up with n inside the
POOL FROG XL Pro
Mineral Cycler. Lower
POOL FROG Mineral
Reservoir into POOL
FROG XL Pro Mineral
Cycler until secure.
6.
SLOT IN THE
POOL FROG
MINERAL
RESERVOIR
FIN INSIDE
POOL FROG
XL PRO
MINERAL
CYCLER
POOL FROG®MINERAL RESERVOIR
The Complete Low-Chlorine Alternative+
www.FrogProducts.com • 800-222-0169
Series 5400 (01-12-5462)
FOR POOLS UP TO 40,000 GALLONS
Product Description: The POOL FROG Mineral Reservoir is the heart of an advanced pool care system that destroys bacteria.
The patented mineral formula in the POOL FROG Mineral Reservoir also neutralizes acids, which helps keep the pH in an
acceptable range with less monitoring. The controlled release of minerals provides an optimum level of protection in your
pool. The FROG Mineral System+reduces chlorine use up to 50%*. Simply use with at least 0.5 ppm of an EPA registered
source of chlorine such as the POOL FROG Bac Pac (EPA Reg. No. 53735-2) or a chlorine delivery device. Using the POOL
FROG Mineral System
+
improves swimming pool pleasure by reducing the problems associated with chlorine including faded
bathing suits, premature damage to pool equipment or surfaces and smelly odors. With the POOL FROG Mineral Reservoir,
pool care is easy and effective. Once wetted, the time-released mineral coating of this product is effective up to 6 consecutive
months or one pool season whichever is shorter. After that time, even if upon shaking you hear the spent media inside, it is
no longer effective and must be replaced. Mark the calendar with stickers provided to replace this product.
Serial No.
5.
DANGER
• Never use fast dissolving chlorine tablets,
liquid bleach, or calcium hypochlorite in
the POOL FROG XL Pro Cyclers.
Mark your calendar ahead for
the six month replacement
of the POOL FROG Mineral
Reservoir. Once wetted,
the time-released mineral
coating of this product
is effective up to 6
consecutive months or one
pool season, whichever is
shorter. After that time you
will hear the spent media
inside, however, it is no
longer effective and must
be replaced.
7.
Remove the POOL FROG Mineral Reservoir and
discard if it has been used for one pool season or
6 months, whichever is shorter.

13
Operate
®
BRAND
2.
Insert upside down into
the open center of the
POOL FROG Mineral
Reservoir pushing
down rmly on FROG
BAM bottle allowing
key in POOL FROG XL
Pro Mineral Cycler to
puncture seal.
Turn control dial on POOL
FROG XL Pro Mineral Cycler to
Setting MAXIMUM.
To remove expended FROG
BAM bottle, turn pump off
and turn dial to Setting 0.
Remove POOL FROG XL Pro
Mineral Cycler cap.
POOL FROG XL Pro
Mineral Cycler
POOL FROG XL Pro
Chlorine Cycler
FROG
BAM
®
BRAND
POOL FROG XL Pro
Mineral Cycler
POOL FROG XL Pro
Chlorine Cycler
FROG
BAM
Using FROG BAM for an Algae-Protection Guarantee
1.
If you are not using FROG BAM, refer to pages 14-15 for Using
the POOL FROG Pac. See FROG BAM product labeling for
complete directions for use (EPA Reg. No. 53735-9).
For a preventive dose add:
•One FROG BAM for pools up to 15,000 gallons.
•Two FROG BAM for pools between 15,000 and 30,000 gallons.
•Three FROG BAM for pools between 30,000 and 40,000 gallons.
Remove cap from FROG BAM
without removing seal.
Turn off pump. Turn control
dial to Minimum or 0. Open
POOL FROG XL Pro Mineral
Cycler cap.
Replace cap by hand only.
DO NOT OVER TIGHTEN.
4.
5. Turn pump on for 90 minutes
allowing FROG BAM to
circulate through pool.
6.
7.
8.
Lift FROG BAM up and allow
any water in the container to
drain through the POOL FROG
XL Pro Mineral Cycler before
discarding in trash or offering
for recycling. Do not reuse or
rell this container.
NOTE: If water shows more
than a hint of blue inside
POOL FROG XL Pro Mineral
Cycler, replace the cap, turn
dial to Maximum and run the
pump for one minute.
8a.If pool size requires
additional FROG BAM, repeat
steps 1-8.
8b. When water is clear in
POOL FROG XL Pro Mineral
Cycler, insert a POOL
FROG Pac according to the
instructions on pages 14-15.
NOTE: If using directly after a shock treatment, test the water rst to ensure the pH is in the proper range of 7.2-7.8 and the chlorine
level is no more than 4.0 ppm. Avoid using other chemicals until this product has been circulated (ltered) for at least 24 hours.
Important: If storing FROG BAM prior to use, always keep in
a cool, dry place away from children and pets.
DANGER
Never use fast dissolving chlorine tablets, liquid bleach,
or calcium hypochlorite in the POOL FROG XL Pro Cyclers.
3.
seal
Looking down at top of bottle

14
POOL FROG Pac is recommended to assure
up to 50% reduction in chlorine use*.
POOL FROG Pac sold separately.
(EPA Reg. No. 53735-2)
Using POOL FROG Pac
Cut handle from POOL FROG Pac using a PVC
cutting tool. (KEEP OUT OF REACH OF CHILDREN).
1.
A. Find the
indent in the
plastic.
B. Place curved section of tool
around the narrow end of one
pac tower and line up blade
on indent.
PVC
cutting tool
available
at local
hardware
stores.
C. Squeeze the handles
together. Repeat for other
side.
D. Make sure the blade comes
straight across on the indent
line for a clean cut.
E. If openings are pinched
together, open with ngers or
re-cut closer to the colored
screens inside POOL FROG
Pac. Leave at least 1/4” of
plastic to t into POOL FROG
XL Pro Chlorine Cycler base.
Finished cut ends
Indent in plastic
®
BRAND
PAC 540C
Avoid a pinched
opening.
A correct
oval opening
Continued to page 15
WARNING
Avoid sparks, smoking, or any open ame near
POOL FROG XL Pro Cyclers or chemicals.
IMPORTANT: Read the label on the POOL FROG Pac carefully
before using.
DANGER
Never use fast dissolving chlorine tablets, liquid bleach,
or calcium hypochlorite in the POOL FROG XL Pro Cyclers.
Invert POOL FROG Pac and
shake slightly until chlorine
tablets fall into tower areas.
Turn off pump. Turn control dial on POOL FROG XL Pro
Chlorine Cycler to 0. Remove cap from POOL FROG XL
Pro Chlorine Cycler and stand back to let any chlorine
fumes dissipate.
2.
3.
POOL FROG
Pac
towers
POOL FROG
Pac
towers

15
Operate
4. Insert POOL FROG Pac
into POOL FROG XL Pro
Chlorine Cycler, lining up
the openings in the POOL
FROG Pac with keys in the
POOL FROG XL Pro Chlorine
Cycler.
NOTE: Openings are a
different shape than keys.
Opening in
POOL FROG Pac
Key in POOL
FROG XL PRO
Chlorine Cycler
Replace cap by hand only.
DO NOT OVERTIGHTEN.
DO NOT USE CAP TOOL TO
TIGHTEN CAP. FOR REMOVAL
ONLY.
5.
POOL FROG XL Pro
Mineral Cycler
POOL FROG XL Pro
Chlorine Cycler
®
BRAND
PAC 540C
Mark your calendar ahead for
the approximate replacement
times for the POOL FROG Pac.
6.
7.
The chlorine pac container is
made of HDPE plastic. Non-
rellable container. Do not
reuse or rell this container.
Offer for recycling if available.
Rinse thoroughly before
recycling or discarding in trash.
WE RECYCLE
Continued....Using POOL FROG Pac
Winterizing
1.
3.
2.
Turn pump off and turn
dial to Setting 0.
Remove both caps.
Unscrew knob in the back
of both POOL FROG XL Pro
Cyclers. Allow all water to
drain.
4.
5.
Remove the POOL FROG
Mineral Reservoir and
discard in trash. You will
hear spent media inside,
however it is no longer
effective.
If POOL FROG Pac still
contains chlorine, wrap in
plastic bag and store in shed
or cool, dry, well-ventilated
location away from children,
pets, cars, motorcycles or
anything metal that can
rust, pit, etc.
If empty, rinse and recycle.
Replace both caps and
knobs loosely.
®
BRAND
PAC 540C
®
BRAND
WARNING
Avoid sparks, smoking, or any open ame near
POOL FROG XL PRO Cyclers or chemicals.
POOL FROG XL Pro
Mineral Cycler
POOL FROG XL Pro
Chlorine Cycler

16
1.
2.
3.
4.
5.
Troubleshooting
For more in-depth troubleshooting, go to frogproducts.com or call King Technology at 800-222-0169.
Problem Remedy
What do I do
if the water looks
cloudy?
1. Make sure your ltration
system is working properly (i.e.
clean lter, skimmer and pump
basket).
2. Make sure circulation time
is adequate – increase pump
time if not.
3. Make sure the pool is
properly balanced (see page
8).
4. Shock the water to
eliminate build up of any
organic matter.
5. Make sure pool has a
free chlorine reading of
0.5 to 1.0 ppm.
6. Check with your dealer for
more information.
What do I do
if the water turns
color?
1. Algae may be trying to form
– shock the pool, increase
circulation time if needed and
clean the lter.
2. Metals in the ll water may
have been oxidized. Have the
pool tested. See pool dealer
if a metal control product is
required.
3. Check with your dealer for
more information.
What do I do
if algae forms in
or on my pool?
1. Use FROG BAM or an effective
algaecide per the directions on
the bottle and brush the sides
of the pool often.
2. Clean the lter and shock
the pool with chlorine daily
until water clarity returns.
3. If you are in an area of the
country that struggles with
algae growth, see your dealer
regarding a 90-day Algae
Protection Guarantee using
FROG BAM. See product
hang tag for guarantee
details.
4. Check with your dealer for
more information.
What do I do
if I am under
chlorinating with
the POOL FROG
Pac?
1. If you are unable to
maintain 0.5 to 1.0 ppm, rst
make sure there are chlorine
tablets in the tower areas
of the POOL FROG Pac and
it is installed properly. If a
correction was made, test the
water in 24 hours.
2. If still low, turn the dial up
one setting and test the water
again in 24 hours. Continue
raising the setting by one
increment each day until the
proper reading is achieved.
3. Shock the pool if the reading
has been lower than 0.5 ppm
for more than one day.
4. Make sure pump run time
is at least 6 hours on high
speed (40 gpm or higher) or
if not, bleed the air from both
cap knobs each time cap is
open.
5. Contact your dealer to have
your back pressure tested.
If under 4 psi consider a
smaller eye-ball tting in the
return jet.
6. Check for a suction side
leak by looking for air bubbles
in your pump basket or at the
return jet. Your water level
will be low and the skimmer
will be taking in air. Contact
dealer for help in correcting
this situation.
7. Contact King Technology’s
Customer Service Department
at 800-222-0169.
What do I do
if I am over
chlorinating with
the POOL FROG
Pac?
1. If the chlorine reading is
over 3.0 ppm, remove the
Chlorine Pac from the POOL
FROG XL Pro Chlorine Cycler
and test the water daily until
the reading is down to 1.0
ppm.
2. Reinsert the POOL FROG
Pac, lower the dial one setting
and test the water again in 24
hours. If the reading has risen,
lower the dial one setting again.
Continue this process until
proper reading is achieved.
3. If over-chlorinating at
the lowest possible setting,
consider decreasing the
circulation time. Depending
on your pump size, you may
be circulating the water more
than is necessary.
4. Contact your dealer to
have your back pressure
tested. If over 8 psi consider
a larger eye-ball tting in the
return jet.
5. Check to see if the pressure
relief valve is loose or missing
and replace. It is a clear plastic
piece approximately 1” long
installed inside near the base. If
loose or missing, it can provide
another avenue for water to
reach the chlorine.
6. Contact King Technology’s
Customer Service Department
at 800-222-0169.

17
For more in-depth troubleshooting, go to frogproducts.com or call King Technology at 800-222-0169.
Parts List
INCLUDED WITH POOL FROG XL Pro CYCLERS
REF. # DESCRIPTION QTY. INCLUDED
1, 2, 3 Caps w/O-Rings 2
4 Body 2
5 Pressure Relief Valve 2
6, 7, 8 Control Dial with O-Ring
& Snap Ring 2
9 & 10 Knob with O-Ring 4
11 2” Male Adapter 2
12 Cap/Control Dial Tool 1
13 Silicone Lubricant 1
14 Shroud 1
REPLACEMENT PARTS FOR POOL FROG XL Pro CYCLERS
REF. # PART NO. DESCRIPTION
1 & 2 01-22-9417 Cap w/O-Ring - Mineral Cycler
3 & 2 01-22-9418 Cap w/O-Ring - Chlorine Cycler
2 01-22-9926 Cap O-Ring
5 01-22-9486 Pressure Relief Valve
6, 7, 8 01-22-9446 Control Dial with O-Ring & Snap Ring
7 & 8 01-22-9456 Control Dial O-Ring Kit
9 & 10 01-22-9946 Knob with O-Ring
12 01-22-8870 Cap/Control Dial Tool
13 01-22-9970 Silicone Lubricant
15 01-22-9950 40k Tune-Up Kit
16 01-22-4000 Pressure Gauge
9
10
12
6
11
910
3
2
4
14
9
10
9
10
1 or 3
2
4
5
8
7
1
2
12
S
IL
I
C
O
N
E
L
U
B
R
I
C
A
N
T
13 15 16
Troubleshoot
part
unavailable,
see your
dealer

18
1.
2.
3.
4.
5.
POOL FROG XL Pro Cyclers Maintenance
Replacing the Control Dial O-Rings
Using a needle nose pliers,
nd the snap ring tail
located at approximately
the ve o’clock position
under the control dial.
Pull down and out of the
groove.
Carefully replace the rubber
O-ring without stretching
it. Apply silicone lubricant,
that came with your POOL
FROG XL Pro Cyclers, on the
O-ring.
Push control dial
completely into the
housing and turn the dial
to setting 2.
7. Using a small screwdriver
or pointed tool to help
guide it, make sure the
snap ring stays in the
groove as it is inserted.
S
IL
I
C
O
N
E
L
U
B
R
I
C
A
N
T
6.
Using a large screwdriver,
loosen the control dial.
Carefully pry the dial until it
pulls out.
Insert the non-lipped end
of snap ring into the groove
opening beginning at the
5 o’clock position and push
it up so that it threads itself
around the control dial.
Product # 01-22-9970

19
Replacing Cap O-Ring Replacing Knobs
To replace, simply unscrew old knob and replace with the
new one.
Continued....POOL FROG XL Pro Cyclers Maintenance
Troubleshoot
Place new O-ring in bottom
half of groove.
Place your thumbs on each
side of the cap over the
O-ring in the groove.
Bottom half
of groove
Top half of
groove
Bottom half
of groove
Top half of
groove
Lubricate O-ring every
couple of months with
silicone lubricant that
came with your POOL
FROG XL Pro Cyclers.
DO NOT USE petroleum
based lubricants.
S
IL
I
C
O
N
E
L
U
B
R
I
C
A
N
T
2.
1.
4.
3.
Product # 01-22-9970
Roll your thumbs back and
forth over the O-ring while
pushing upward until the
O-ring falls into the top of
the groove.
Remove old O-ring.
Back of Cycler
Top of Cap

20
POOL FROG XL Pro Two-Year Limited Warranty
King Technology, Inc. will warrant this unit with a complete replace-
ment for the original purchaser, should it prove defective by reason of
improper workmanship and/or material for a period of two (2) years
from the date of original purchase/installation. This warranty covers
body, cap and control dial excluding O-rings. King Technology holds
the option of replacing any defective part without charge if it is de-
termined to be all that is needed to correct any situation. Parts used
for replacement, with the exception of O-rings, are warranted for the
remainder of the original warranty.
1. To obtain warranty service, you must deliver product to King Tech-
nology or its nearest authorized dealer. Shipping expenses are the
purchaser’s responsibility. The name of the nearest authorized deal-
er can be obtained at frogproducts.com/nd-a-dealer or by calling
King Technology at 1-800-222-0169. Proof of purchase is required
when requesting warranty service. Purchaser must present the sales
receipt or other document which establishes proof of purchase. To
extend your warranty to 10 years, go to frogproducts.com/reg.
2. This warranty does not cover defects caused by: modication,
alteration, repair or service of the product contrary to the accom-
panying instructions; physical abuse to or misuse of the product or
operation or installation in a manner contrary to the accompanying
instructions. This warranty also excludes all costs arising from the
installation, adjustment, removal or replacement of defective units
or parts. This warranty also excludes any and all claims arising out of
the chemicals used in the product or their characteristics.
3. Any express warranty not provided for herein, and any remedy
for breach of warranty or breach of contract which, but for this
provision, might arise by implication or operation of law, is hereby
expressly excluded and disclaimed. The implied warranties of mer-
chantability and of tness for any particular purpose are expressly
limited to a term of two years. Some states do not allow limitation
on how long an implied warranty lasts, so the above limitation may
not apply to you.
4. Under no circumstance shall King Technology be liable to pur-
chaser or any other person for any damage or loss incurred be-
cause of any chemicals used in the product or their physical char-
acteristics, or interruption of service of the product, or any special,
incidental or consequential damages or losses, whether arising out
of breach of warranty, breach of contract or otherwise. Some states
do not allow the exclusion or limitation of incidental consequential
damages, so the above limitation or exclusion may not apply to you.
5. Misuse or failure to use the proper POOL FROG Mineral Reservoir
and POOL FROG Pac may cause damage to equipment or personal
injury. All warranty null and void if this product is not used with the
recommended POOL FROG Mineral Reservoir and POOL FROG Pac.
Register your warranty today at frogproducts.com/reg and extend the standard 2-year warranty to
10 years of coverage.
Made in U.S.A.
Patents: kingtechnology.com/IP
MANUFACTURED BY
FROG® FROG BAM®SmartChlor®
POOL FROG® FROG Serene™FROG Jump Start®
POOL FROG XL PRO® FROG Filter Mate™Fresh Mineral Water®
Flippin’ FROG®INSTANT FROG®New Water®
Flippin’ FROG XL®FROG @ease®Perform-Max
530 11TH AVE S, HOPKINS, MN 55343 | 800.222.0169 | frogproducts.com
© King Technology, Inc. The following are trademarks of King Technology, Inc.
20-48-0220 553121843R8N
Don’t forget to register your warranty and sign up to receive emails on special offers and helpful
water care tips. Visit frogproducts.com/reg