POOLEX Triline SELECTiON 150 User manual

INSTALLATION
AND
USER MANUAL
for your heat pump
Models 150 / 180 / 220

2

3
Dear Customer,
Thank you for your purchase and for your condence in our products.
These are the result of many years of research in the eld of design and production
of heat pumps for swimming pools. Our aim is to provide you with an exceptional high
performance quality product.
We have produced this manual with the utmost care so that you get maximum benet
from your Poolex heat pump.
Thank you

4
PLEASE READ CAREFULLY.
These installation instructions are an integral part of the product.
They must be given to the installer and retained by the user.
If the manual is lost, please consult the website:
www.poolex.fr
The instructions and recommendations contained in this manual should be read carefully and understood
since they provide valuable information concerning the heat pump’s safe handling and operation. Keep this
manual in an accessible place for easy future reference.
Installation must be carried out by a qualied professional person in accordance with current regu-
lations and the manufacturer’s instructions. An installation error may cause physical injury to persons or
animals as well as mechanical damage for which the manufacturer can under no circumstances be held
responsible.
After unpacking the heat pump, please check the contents in order to
report any damage. Please also check that the pressure indicated on the gauge is higher than 80
psi. If not, this could mean a leak of refrigerant.
Prior to connecting the heat pump, ensure that the information provided in this manual is compatible with
the actual installation conditions and does not exceed the maximum limits authorised for this particular
product.
In the event of a defect and/or malfunction of the heat pump, the electricity supply must be discon-
nected and no attempt made to repair the fault.
Repairs must be undertaken only by an authorised technical service organisation using original replace-
ment parts. Failure to comply with the above-mentioned clauses may have an adverse effect on the heat
pump’s safe operation.
To guarantee the heat pump’s efciency and satisfactory operation, it is important to ensure its regular
maintenance in accordance with the instructions provided.
If the heat pump is sold or transferred, always make sure that all technical documentation is transmitted
with the equipment to the new owner.
This heat pump is designed solely for heating a swimming pool. Any other use must be considered as being
inappropriate, incorrect or even hazardous.
! !
Any contractual or non-contractual liability of the manufacturer/distributor shall be deemed null and void for
damage caused by installation or operational errors, or due to non-compliance with the instructions provid-
ed in this manual or with current installation norms applicable to the equipment covered by this document.

5
Contents
1. General ............................................................................................................................................................................................ 6
1.1 General Terms of Delivery ......................................................................................................................................................... 6
1.2 Safety instructions....................................................................................................................................................................... 6
1.3 Water treatment ......................................................................................................................................................................... 7
2. Description...................................................................................................................................................................................... 8
2.1 Package contents ...................................................................................................................................................................... 8
2.2 General characteristics .............................................................................................................................................................. 8
2.3 Technical specications .............................................................................................................................................................. 9
2.4 Unit dimensions ........................................................................................................................................................................ 10
2.5 Exploded view............................................................................................................................................................................11
3. Installation..................................................................................................................................................................................... 12
3.1 Pre-requirements ...................................................................................................................................................................... 12
3.2 Location .................................................................................................................................................................................... 12
3.3 Installation layout ...................................................................................................................................................................... 13
3.4 Connecting the condensation draining kit................................................................................................................................. 13
3.5 Installing the unit on noise-damping supports........................................................................................................................... 13
3.6 Hydraulic connection................................................................................................................................................................. 14
3.7 Electrical installation ................................................................................................................................................................. 16
3.8 Electrical connection ................................................................................................................................................................ 17
3.9 Wall–mounting the remote control ........................................................................................................................................... 18
4. Use................................................................................................................................................................................................. 19
4.1 Wired remote control................................................................................................................................................................. 19
4.2 Operating mode selector........................................................................................................................................................... 19
4.3 Automatic Mode........................................................................................................................................................................ 20
4.4 Cooling Mode............................................................................................................................................................................ 21
4.5 Heating Mode............................................................................................................................................................................ 22
4.6 Setting the clock ....................................................................................................................................................................... 23
4.7 Programming Start/Stop ........................................................................................................................................................... 24
4.8 Activating a programme ........................................................................................................................................................... 25
4.9 Deactivating a programme ....................................................................................................................................................... 25
4.10 Status values and advanced settings ....................................................................................................................................... 26
5. Operation....................................................................................................................................................................................... 28
5.1 Operation .................................................................................................................................................................................. 28
5.2 Servo-control of circulating pump ............................................................................................................................................. 29
5.3 Using the pressure gauge......................................................................................................................................................... 29
5.4 Antifreeze protection................................................................................................................................................................. 30
6. Maintenance and servicing.......................................................................................................................................................... 31
6.1 Maintenance and servicing ....................................................................................................................................................... 31
6.2 Winter storage .......................................................................................................................................................................... 31
7. Repairs .......................................................................................................................................................................................... 32
7.1 Breakdowns and faults.............................................................................................................................................................. 32
7.2 List of faults............................................................................................................................................................................... 33
8. Recycling....................................................................................................................................................................................... 34
8.1 Recycling the heat pump .......................................................................................................................................................... 34
9. Warranty ........................................................................................................................................................................................ 35
9.1 General warranty conditions ..................................................................................................................................................... 35
10. Appendices ................................................................................................................................................................................. 36
10.1 Wiring diagrams ....................................................................................................................................................................... 36

6
All equipment, even if shipped ‘free of carriage and packing’, is dispatched at the consignee’s own risk
The person responsible for receiving the equipment must carry out a visual inspection to identify any dam-
age to the heat pump during transport (refrigerant system, body panels, electrical control box, frame). He/
she must note down on the carrier’s delivery note any remarks concerning damage caused during transport
and conrm them to the carrier by registered letter within 48 hours.
The equipment must always be stored and transported vertically on a pallet and in its original packaging. If
it is stored or transported horizontally, wait at least 24 hours before switching it on.
During installation and servicing
Only a qualied person may undertake installation, start-up, servicing and repairs, in compliance with
current standards.
Before operating or undertaking any work on the equipment (installation, commissioning, usage, servicing),
the person responsible must be aware of all the instructions in the heat pump’s installation manual as well
as the technical specications.
Under no circumstances install the equipment close to a source of heat, combustible materials or a build-
ing’s air intake.
If installation is not in a location with restricted access, a heat pump protective grille must be tted.
To avoid severe burns, do not walk on pipework during installation, repairs or maintenance.
To avoid severe burns, prior to any work on the refrigerant system, turn off the heat pump and wait several
minutes before placing temperature and pressure sensors.
Check the refrigerant level when servicing the heat pump.
Check that the high and low pressure switches are correctly connected to the refrigerant system and that
they turn off the electrical circuit if tripped during the equipment’s annual leakage inspection.
Check that there is no trace of corrosion or oil stains around the refrigerant components.
1.2 Safety instructions
1.1 General Terms of Delivery
WARNING: Please read carefully the safety instructions before using the equipment.
The following instructions are essential for safety so please strictly comply with them.
1. General

7
1.3 Water treatment
Poolex heat pumps for swimming pools can be used with all types of water treatment systems.
Nevertheless, it is essential that the treatment system (chlorine, pH, bromine and/or salt chlorinator meter-
ing pumps) is installed after the heat pump in the hydraulic circuit.
To avoid any deterioration to the heat pump, the water’s pH must be maintained between 6.9 and
8.0.
1. General
During use
To avoid serious injuries, never touch the fan when it is operating.
Keep the heat pump out of the reach of children to avoid serious injuries caused by the heat exchanger’s
blades.
Never start the equipment if there is no water in the pool or if the circulating pump is stopped.
Check the water ow rate every month and clean the lter if necessary.
During cleaning
Switch off the equipment’s electricity supply.
Close the water inlet and outlet valves.
Do not insert anything into the air or water intakes or outlets.
Do not rinse the equipment with water.
During repairs
Carry out work on the refrigerant system in accordance with current safety regulations.
Brazing should be performed by a qualied welder.
When replacing a defective refrigerant component, use only parts certied by our technical department.
When replacing pipework, only copper pipes conforming to Standard NF EN12735-1 may be used for
repairs.
When pressure-testing to detect leaks:
To avoid the risks of re or explosion, never use oxygen or dry air.
Use dehydrated nitrogen or a mixture of nitrogen and refrigerant.
The low and high side test pressure must not exceed 42 bar.

8
2.1 Package contents
2.2 General characteristics
✔Heat pump Poolex Triline Selection
✔2 hydraulic inlet/outlet connectors (50mm diameter)
✔Extension cable for remote control panel
✔This installation and user manual
✔Condensation draining kit
✔Winter storage cover
✔4 anti-vibration pads (fastenings not supplied)
A Poolex heat pump has the following features:
CE certication and complies with the RoHS European directive.
High performance with up to 80% energy savings compared to a conventional heating system.
Clean, efcient and environmentally friendly R410A refrigerant.
Reliable high output leading brand compressor.
Wide hydrophilic aluminium evaporator for use at low temperatures.
User-friendly intuitive remote control.
Heavy duty ABS shell, anti-UV treated and easy to maintain.
Designed to be silent.
Dual antifreeze system to avoid frost damage:
Revolutionary exchanger with patented antifreeze system.
A smart monitoring system to preserve the pipework and liner without emptying the pool in winter.
2. Description

9
2.3 Technical specications
2. Description
The technical specications of our heat pumps are provided for information purposes only. We reserve the right to make changes without prior notice.
1 Ambient air temperature
2 Initial water temperature
3Noise at 1 m, at 4 m and at 10 m in accordance with Directives EN ISO 3741 and EN ISO 354
4Calculated for an in-ground private swimming pool covered with a bubble cover.
5Value indicated on the unit’s nameplate.
Poolex Triline Selection
Test conditions 150 180 220
Air (1) 26°C
Water (2) 26°C
Heating power (W) 21010 25620 30660
Consumption (W) 3410 4160 4970
COP (Coeff. of performance) 6,16 6,16 6,17
Air (1) 15°C
Water (2) 13°C
Heating power (W) 16530 19850 24260
Consumption (W) 2680 3230 3930
COP (Coeff. of performance) 6,16 6,15 6,16
Air (1) 15°C
Water (2) 26°C
Heating power (W) 15120 18060 22050
Consumption (W) 2950 3550 4320
COP (Coeff. of performance) 5,11 5,08 5,10
Air (1) 20°C
Water (2) 24°C
Heating power (W) 16980 20350 24920
Consumption (W) 2990 3590 4400
COP (Coeff. of performance) 5,68 5,66 5,67
Air (1) 35°C
Water (2) 27°C
Cooling capacity (W) 13200 15830 19500
Consumption (W) 3830 4610 5630
EER (Energy Efciency Ratio) 3,44 3,43 3,46
Maximum power (W) 5530 6710 8190
Maximum current (A) 8,43 10,23 12,5
Electricity supply Triphasée 380-415V/3N~50Hz
Heating temperature range 15°C~40°C
Cooling temperature range 8°C~28°C
Operating range -10°C~43°C
Unit dimensions L x W x H (mm) 740 x 700 x 900
Unit weight (kg) 102 109 114
Sound pressure level at 1 m (dBA) (3) <51 <52 <53
Sound pressure level at 4 m (dBA) (3) <41 <42 <43
Sound pressure level at 10 m (dBA) (3) <32 <33 <34
Hydraulic connection (mm) PVC 50mm
Heat exchanger PVC tank and titanium heating coil
Min. water ow rate (m³/h) 4.2 / 8.5 5.1 / 10.3 6.3 / 12.5
Compressor Mitsubishi Panasonic Panasonic
Compressor type Rotary Scroll Scroll
Refrigerant R410A
Refrigerant content (kg) 2,5 2,7 3,4
GWP 2088 2088 2088
CO2 equivalent 5,22 5,64 7,10
Load loss (mCE) 1,3 1,31 1,31
Max. pool volume (m3) (4) ≤120 ≤140 ≤160
Remote control Wired backlit LCD monitor screen
Mode Heating/Cooling/Auto

10
2.4 Unit dimensions
2. Description
Dimensions in mm
Model Triline Selection
150 / 180 / 220
A735
B700
C700
D143
E395
F905
G111.5
H160
B
A
C
E D
F
GH

11
2.5 Exploded view
1. Front panel A
2. Pressure gauge
3. Front panel B
4. Sealed enclosure for remote control
5. Heat exchanger
6. Assembly frame A
7. Fan support
8. Fan motor
9. Fan blade
10. Assembly frame B
11. Top panel
12. Fan protective grill
13. Evaporator
14. Right panel
15. Assembly frame C
16. 4-way valve
17. Compressor
18. Electronic expansion valve
19. Electrical box and terminal
20. Electrical box cover
2. Description
1
2
3
4
6
10
12
11
7
8
5
9
14
13
15
16
17
18
19
20

12
Equipment necessary for the installation of your heat pump:
Power supply cable suitable for the unit’s power requirements.
A By-Pass kit and an assembly of PVC tubing suitable for your installation as well as stripper, PVC
adhesive and sandpaper.
A set of wall plugs and expansion screws suitable to attach the unit to your support.
We recommend that you connect the unit to your installation by means of exible PVC pipes in order to
reduce the transmission of vibrations.
Suitable fastening studs may be used to raise the unit.
3.1 Pre-requirements
3.2 Location
Please comply with the following rules concerning the choice of heat pump location.
1. The unit’s future location must be easily accessible for convenient operation and maintenance.
2. It must be installed on the ground, xed ideally on a level concrete oor. Ensure that the oor is sufciently
stable and can support the weight of the unit.
3. A water drainage device must be provided close to the unit in order to protect the area where it is installed.
4. If necessary, the unit may be raised by using suitable mounting pads designed to support its weight.
5. Check that the unit is properly ventilated, that the air outlet is not facing the windows of neighbouring
buildings and that the exhaust air cannot return. In addition, provide sufcient space around the unit for
servicing and maintenance operations.
6. The unit must not be installed in an area exposed to oil, ammable gases, corrosive products, sulphurous
compounds or close to high frequency equipment.
7. To prevent mud splashes, do not install the unit near a road or track.
8. To avoid causing nuisance to neighbours, make sure the unit is installed so that it is positioned towards
the area that is least sensitive to noise.
9. Keep the unit as much as possible out of the reach of children.
3. Installation
WARNING: Installation must be carried out by a qualied engineer.
This section is provided for information purposes only and must be checked and adapted if
necessary according to the actual installation conditions.
Place nothing less than one metre in front of the heat pump.
Leave 50 cm of empty space around the sides and rear of the heat pump.
Do not leave any obstacle above or in front of the unit!
Dimensions in mm.

13
3.3 Installation layout
3.4 Connecting the condensation draining kit
3.5 Installing the unit on noise-damping supports
While operating, the heat pump is subject to condensation. This will result in a more or less large run-off
of water, depending on the degree of humidity. To channel this ow, we recommend that you install the
condensation drainage kit.
How do you install the condensation drainage kit|?
Install the heat pump, raising it at least 10 cm with solid water-resistant pads, then connect the drainage
pipe to the opening located under the pump.
In order to minimise the noise pollution associated with heat pump vibrations, it can be positioned on
vibration absorbing pads.
To do this, you simply have to position a pad between each of the unit’s feet and its support, and then x
the heat pump to the support with suitable screws.
3. Installation
Valves 1, 2 and 3: Bypass valves
Valves 4 and 5: Regulating valves
(Recommended for facilitating adjustments close to the machine)
Half-open valve Open valve
Key
Heat pump
Water outlet
Water intake
Elevating
studs Drain
plug
Condensation
draining
Valve 4
Valve 5
Valve 3 Valve 2
Circulating
pump
Filtration
Valve 1
Automated treatment system
(salt chlorinator, metering pump)
TOWARDS THE POOL
FROM THE POOL
4-way valve

14
Making a hydraulic connection with the By-Pass kit
Step 1: Take the necessary steps to cut your pipes.
Step 2: Make a straight perpendicular cut through the PVC pipes with a saw.
Step 3: Assemble your hydraulic circuit without connecting it in order to check that it perfectly ts your
installation, then dismantle the pipes to be connected.
Step 4: Chamfer the ends of the cut pipes with sandpaper.
Step 5: Apply stripper to the ends of the pipes to be connected.
Step 6: Apply the adhesive in the same place.
Step 7: Assemble the pipes.
Step 7: Clean off any adhesive remaining on the PVC.
Step 8: Leave to dry for at least 2 hours before putting the hydraulic circuit into water.
3.6 Hydraulic connection
3. Installation
WARNING: Installation must be carried out by a qualied engineer.
This section is provided for information purposes only and must be checked and adapted if
necessary according to the actual installation conditions.
WARNING: Do not run water through the hydraulic circuit for 2 hours after applying the adhesive.
By-Pass assembly
The heat pump must be connected to the pool by
means of a By-Pass assembly.
A By-Pass is an assembly consisting of 3 valves that
regulate the ow circulating in the heat pump.
During maintenance operations, the By-Pass permits
the heat pump to be isolated from the system without
interrupting your installation.
TOWARDS THE POOL
Open valve
Half-open valve
FROM THE POOL

15
By-Pass assembly for more than one heat pump
By-Pass assembly for one heat pump
The lter located upstream of the heat pump must be regularly cleared so that the water in
the system is clean, thus avoiding the operational problems associated with dirt or clog-
ging in the lter.
3. Installation
Half-open valve
Half-open valve
Open valve
Open valve
Key
Key
TOWARDS THE POOL
Filtration + Pump
Filtration + Pump
Automated treatment
system
Automated treatment
system
TOWARDS THE POOL
FROM THE POOL
POOL
POOL
FROM THE POOL

16
3. Installation
To function safely and maintain the integrity of your electrical system, the unit must be connected to a
general electricity supply in accordance with the following regulations:
Upstream, the general electricity supply must be protected by a 30 mA differential switch.
The heat pump must be connected to a suitable D-curve circuit breaker (see table below) in accordance
with current standards and regulations in the country where the system is installed.
The electricity supply cable must be adapted to match the unit’s rated power and the length of wiring
required by the installation (see table below). The cable must be suitable for outdoor use.
For a three-phase system, it is essential to connect the phases in the correct sequence.
If the phases are inverted, the heat pump’s compressor will not work.
In places open to the public, it is mandatory to install an emergency stop button close to the heat pump.
Models Electricity supply Max. current Cable diameter Protection Thermal-magnetic (D
curve) protection
Triline Selection 150
3-phase
380-415V/3N~50Hz
8.43 A RO2V 5x2,5 mm² 20A
Triline Selection 180 10.23 A RO2V 5x2,5 mm² 20A
Triline Selection 220 12.5 A RO2V 5x2,5 mm² 25A
1Cable cross-section suitable for max. length 10 metres. For longer than 10 metres, consult an electrician.
3.7 Electrical installation
WARNING: Installation must be carried out by a qualied engineer.
This section is provided for information purposes only and must be checked and adapted if
necessary according to the actual installation conditions.

17
Please comply with the following instructions to electrically connect the heat pump.
Step 1: Detach the electrical side panel with a screwdriver to access the electrical terminal block.
Step 2: Insert the cable into the heat pump unit by passing it through the opening provided for that purpose.
Step 3: Connect the power supply cable to the terminal block in accordance with the diagram below.
Step 4: Carefully close the heat pump panel.
Servo-control of circulating pump
Depending on the type of installation, you can also connect a circulating pump to terminals P1and P2so
that this operates in tandem with the heat pump.
3. Installation
3.8 Electrical connection
WARNING: The heat pump’s power supply MUST be disconnected before any operation.
WARNING: Servo-control of a pump whose power exceeds 5A (1000W) requires the use of a
power relay.
P1P2
PHASE TERRENEUTRE
Connecter à la
pompe de circulation
ou un relais de puissance
C N
PHASE CPHASE BPHASE A NEUTRE TERRE
BA
Connecter à l’alimentation
Triphasée
400V / 50Hz
3-phase model
PHASE NEUTRAL EARTHPHASE A PHASE B PHASE C NEUTRAL EARTH
Connect to power supply
3-phase
400V/50Hz
Connect to a ltration
pump or a power relay

18
3.9 Wall–mounting the remote control
Step 1: Detach the remote control from the machine. Pay attention to the communication wire connected
to the printed circuit board and separate them carefully.
Step 2: Use a screwdriver to open the casing and separate the remote control.
Step 3: Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4: Attach the remote control’s rear cover to the wall.
Step 5: Align the front and rear covers exactly, ensuring that the box is xed rmly to the wall.
Step 6: Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you may
damage it. When the remote control is xed to the wall, do not pull the communication wire, this may
cause a loose contact.
3. Installation
Step 1
Step 4
Step 2
Step 5
Step 3
Step 6
60mm

19
4.2 Operating mode selector
Prior to setting your required temperature, you must rst select an operating mode for your heat pump:
4. Use
4.1 Wired remote control
3. Installation
Before starting, ensure that the ltration pump is working and that water is circulating through
the heat pump.
Button: On/Off
Button: Clock and Timers
Button: Operating mode
Water temperature
Outside temperature
Clock
Operating mode
Automatic Mode (warm, cold)
Select the Automatic mode for the heat pump to switch automatically to Heating
or Cooling (depending on the actual pool temperature) in order to reach the
desired temperature.
Cooling Mode
Select the cooling mode for the heat pump to cool the water in your pool.
Heating Mode
Select the heating mode for the heat pump to heat the water in your pool.

20
WARNING: When the cooling mode switches to heating mode or vice-versa, the heat pump will restart
after 10 minutes.
Useful information
Step 1: Press to switch on your pump.
Step 2: Press to switch from one mode to another until Automatic mode is displayed.
Step 3: Select the desired temperature by using the buttons and (8-40°C).
Automatic cooling:
When the incoming water temperature is higher or equal to the required temperature (setpoint temperature)
+(X+2)°C, the heat pump will switch to cooling mode. The compressor will stop when the temperature of the
incoming water equals the required temperature (setpoint temperature).
Automatic heating:
When the water temperature is less than or equal to the required temperature (setpoint temperature) - X°C,
the heat pump will switch to heating mode and stop when the incoming water temperature is equal to the
required temperature (setpoint temperature).
Indicators for adjustment range X and Y
X : adjustable parameter from 2° to 10°C, default setting is 3°C
Y : adjustable parameter from 0° to 6°C, default setting is 0°C
EXAMPLE:
If you have selected 28°C, your screen will display:
Once the symbol stops
blinking, the required temperature
is validated and is replaced by the
water’s current temperature (25°
in our example).
Required
temperature
“Blinking”
Current water
temperature
Current temperature
of the ambient air
4. Use
4.3 Automatic Mode
WARNING: Before starting, ensure that the ltration pump is operating correctly.