Porcher 5339 Series User manual

5339 Series
T339 Series
SHOWER
SYSTEM
VALVE
ONLY
B/S With
DIVERTER
BATH
FILLER
To assure proper positioning in relation to wall, note
roughing-in dimensions.
ROUGHING-IN DIMENSIONS
Certified to comply with ANSI A112.18.1
Installation
Instructions
THREADED INLETS (STOPS)
INLETS
1/2" NPT
(13mm)
5-5/8" (143mm)
1-3/4"
(44mm)
OUTLETS 1/2" NPT (13mm)
5-5/8"
(143mm)
1ROUGHING-IN Turn off water at main supply.
CAUTION
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS. When finished soldering,
flush valve body, replace cartridges, check stops and plaster guard to continue installation. Use thread
sealant or Teflon tape on threaded connections.
NOTE
If the valve is installed on a fiberglass
or other thin wall application, the
PLASTER GUARD (4) can be used as a support.
Connect hot and cold water supplies.
Cap off shower pipe (5) and tub filler pipe (6).
For support, use pipe BRACES (7) secured to wooden braces.
With valve turned off, turn on water supplies. Check for leaks.
COLD
HOT
Cut a 4" dia. hole in the shower stall.
Drill two additional 1" holes to allow access
to the stops.
Remove PLASTER GUARD (4), rotate 180˚
so that indicated screw holes fit MANIFOLD (2).
Push CAP on valve, place ESCUTCHEON on and
attach with screws.
1
7
5
3
6
4
2
See Roughing-in diagram before starting.
Connections are:
1/2" female NPT for threaded inlets
Connect RISER PIPE (1) to MANIFOLD (2)
top outlet marked "SHR".
Connect TUB FILLER PIPE (3) at bottom
outlet marked "TUB".
For proper positioning the finished wall
must be within side wall of PLASTER
GUARD (4).
Recommended Tools
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
STEMMA
Thank you for selecting Porcher Products.
To ensure that your installation proceeds
smoothly--please read these instructions
carefully before you begin.
1-5/8" TO 3-1/4"
(41mm TO 83mm)
FINISHED WALL
BOTTOM OF
TUB
BOTTOM OF
TUB
74" FOR
HEAD CLEARANCE
(1880mm)
2-7/8" REF.
(73mm)
1/2" NPT (13mm)
1" (25mm)
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65'' AND 78''
(1651 AND 2026mm)
8" REF.
(203mm)
4"
(102mm)
6-3/4"
(171mm)
7-1/2"
(191mm)
1/2" NPT (13mm)
18"
OPTIONAL
(457mm)
"SEE ILLUSTRATION"
NOTE: ALL DIMENSIONS
ARE TYPICAL TO B/S WITH
DIVERTER
TOP OF
TUB RIM
TOP OF
TUB RIM
SHW
TUB
1" (25mm)
SHW
TUB
M968454A
Pipe Wrench
BATH/SHOWER WITH DIVERTER
SHOWER OR BATH FILLER ONLY
PRESSURE BALANCE
TEMPERATURE CONTROL VALVE

3INSTALL TRIM
2INSTALL DIVERTER (Models 5339.600/.602)
When finished tiling the wall, remove PLASTER GUARD (1).
Remove two screws that secure the DIVERTER LID (2) and
remove Lid. Inspect the inside surface of diverter port.
Diverter port must be free of any dirt. Clean if necessary.
Install DIVERTER (3) with SCREWS (4) removed from
DIVERTER LID (2).
Operate DIVERTER (3). DIVERTER (3) should slide in
and out smoothly.
1
2
4
3
M968454A
DIVERTER
PORT
CAUTION: Protect finish on SHOWER HEAD and TUB SPOUT when installing.
Push on DIVERTER COVER (1). (Models 5339.600/.602)
Turn VALVE STEM (9) clockwise to off position.
Push CAP (2) on valve. Place ESCUTCHEON HOLDER (3) onto
CAP (2) and attach with LONG SCREWS (4).
Place ESCUTCHEON (5) onto CAP (2) and attach with SHORT SCREWS (6)
to ESCUTCHEON HOLDER (3).
Push DECORATIVE RING (7) onto CAP (2) until seated flush against
ESCUTCHEON (5). Push ADAPTER (8) onto VALVE STEM (9) and attach
to VALVE STEM (9) with SCREW (10).
Align HANDLE (11) and thread onto ADAPTER (8).
Screw DIVERTER KNOB (15) onto diverter stem. (Models 5339.600/.602)
Remove pipe caps from rough-in nipples.
To install SHOWER HEAD (12) slide ESCUTCHEON (13) away from wall to expose
hex. Install SHOWER HEAD (12) and push ESCUTCHEON (13) flush with finished wall.
Thread TUB SPOUT (14) onto spout nipple.
14
2
3
5
7
8
10
11
4
9
1
12
15
6
Hot
Cold
Off
VALVE
PIPE CAP
PIPE CAP
13

5
Pull INDEX CAP, unscrew HANDLE SCREW and pull HANDLE off valve stem.
Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON. Remove COVER by pulling straight out.
Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS on valve.
TO GAIN ACCESS TO VALVE FOR SERVICING
6
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and
pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove
CAPS (7) and check O-RINGS on inside of CAPS (7). Clean inside sealing surfaces of VALVE BODY (8).
Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws.
Turn on water supply and see above for installing TRIM and HANDLE.
VALVE LEAKS WHEN SHUT OFF
BACK TO BACK INSTALLATION
BACK TO BACK INSTALLATION
ROTATE 180˚
Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7) and clean valve thoroughly.
Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair
Part M952100-0070A if balancing unit is defective.
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the
large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should
butt up against top of casting.
Reassemble FIXATION RING (4) and CARTRIDGE (1).
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
1
2
9
5
5
7
8
6
4
3
INLETS
LARGE OUTLET
M968454A
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP (1) reduces risk of accidental scalding. To set the maximum
hot water temperature of your faucet, all you need to do
is adjust the setting on the HOT LIMIT SAFETY STOP (1).
1
5
1
3
1
1
9
7
5
3
1
0
1
5
1
3
1
1
9
7
5
3
1
1
5
1
3
1
1
9
7
5
3
1
4
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
Turn CARTRIDGE STEM (2) to the OFF position (coldest setting)
before making adjustment to HOT LIMIT STOP (1). Use a flat
blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1).
Pull forward and rotate counterclockwise one number to limit hot
water temperature. Use ARROW (3) on CARTRIDGE (4) and
NUMBERS (5) on HOT LIMIT STOP (1) for indication.
1
5
1
5
4
4
3
3
2
2

MODEL NUMBER
1
5
1
3
1
1
9
7
5
3
1
STEMMA
CHROME 002
M962181-YYY0A
ESCUTCHEON
KIT & SCREWS
Product names listed herein are trademarks of Porcher, Ltd.
©Porcher, Ltd.2003
IN CANADA 480-961-5353
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 to 7:00 p.m. EST
HOTLINE FOR HELP
M968454A
A909779-YYY0A
DECORATIVE RING
A918647-0070A
ESCUTCHEON
SCREWS
M907053-YYY0A
ESCUTCHEON CAP
M962180-0070A
ESCUTCHEON HOLDER
922388-YYY0A
STREAM STRAIGHTENER
Replace the "YYY" with
appropriate finish code
A954440-0070A
CARTRIDGE
023603-0070A
CARTRIDGE SCREWS
A923611-0070A
HOT LIMIT STOP
M961854-0070A
FIXATION RING
WITH SCREWS
051122-0070A
SCREWDRIVER STOPS
M952100-0070A
PRESSURE
BALANCING UNIT
027816-0070A
1/2" NPT PLUG (13mm)
BATH/SHOWER WITH DIVERTER
SHOWER OR BATH FILLER ONLY
5339 SERIES
T339 SERIES
Hot
Cold
Off
A953929-0070A
DIVERTER KIT
M907103-YYY0A
DIVERTER COVER
A909928-YYY0A
DIVERTER KNOB
M950125-YYY0A
ADJ. SHOWER HEAD
M962177-YYY0A
ESCUTCHEON
KIT & SCREWS
Hot
Cold
Off
PRESSURE
BALANCE TEMPERATURE
CONTROL VALVE
M918453-0070A
ADAPTER
A918511-0070A
ADAPTER SCREW
A954437-YYY0A
HANDLE KIT
A960536-YYY0A
TUB SPOUT KIT
M907571-YYY0A
SPOUT ESCUTCHEON