Portwell PEB-2772VGATM User manual

PEB-2772VGATM
Embedded System Board
User's Manual
Version 1.1
Copyright © Portwell, Inc., 2012 All rights reserved.
All other brand names are registered trademarks of their respective owners.

Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview.......................................................................................................1-1
1.1 Introduction ....................................................................................................... 1-1
1.2 Check List........................................................................................................... 1-1
1.3 Product Specification........................................................................................ 1-2
1.4 System Configuration....................................................................................... 1-3
1.5 System Architecture.......................................................................................... 1-5
Chapter 2 Hardware Configuration...........................................................................................2-1
2.1 Jumper Setting................................................................................................... 2-1
2.2 Connector Allocation........................................................................................ 2-3
Chapter 3 System Installation....................................................................................................3-1
3.1 Intel ® Atom TM Processor D2550................................................................. 3-1
3.2 Main Memory .................................................................................................... 3-1
3.3 Installing the Single Board Computer............................................................ 3-1
3.3.1 Chipset Component Driver .................................................................... 3-3
3.3.2 Intel Graphics Media accelerator........................................................... 3-3
3.3.3 Intel Gigabit Ethernet Controller ........................................................... 3-3
3.3.4 Audio Controller...................................................................................... 3-3
3.4 Clear CMOS Operation .................................................................................... 3-4
3.5 WDT Function ................................................................................................... 3-5
3.6 GPIO.................................................................................................................... 3-7
Chapter 4 BIOS Setup Information............................................................................................4-1
4.1 Entering Setup ................................................................................................... 4-1
4.2 Main .................................................................................................................... 4-2
4.3 Configuration .................................................................................................... 4-3
4.4 Security ............................................................................................................. 4-20
4.5 Boot ................................................................................................................... 4-21
4.6 Security ............................................................................................................. 4-22
Chapter 5 Troubleshooting........................................................................................................5-1
5.1 Hardware Quick Installation........................................................................... 5-1
5.2 FAQ ..................................................................................................................... 5-2
Appendix A
Appendix B

Preface
How to Use This Manual
The manual describes how to configure your PEB-2772
system to meet various operating requirements. It is divided into five chapters, with
each chapter addressing a basic concept and operation of Single Host Board.
Chapter 1 : System Overview. Presents what you have in the box and give you an
overview of the product specifications and basic system architecture for this series
model of single host board.
Chapter 2 : Hardware Configuration. Shows the definitions and locations of Jumpers
and Connectors that you can easily configure your system.
Chapter 3 : System Installation. Describes how to properly mount the CPU, main
memory and Compact Flash to get a safe installation and provides a programming
guide of Watch Dog Timer function.
Chapter 4 : BIOS Setup Information. Specifies the meaning of each setup
parameters, how to get advanced BIOS performance and update new BIOS. In
addition, POST checkpoint list will give users some guidelines of trouble-shooting.
Chapter 5 : Troubleshooting. Provides various useful tips to quickly get PEB-2772
running with success. As basic hardware installation has been addressed in Chapter
3, this chapter will basically focus on system integration issues, in terms of backplane
setup, BIOS setting, and OS diagnostics.
The content of this manual is subject to change without prior notice. These changes
will be incorporated in new editions of the document. Portwell may make
supplement or change in the products described in this document at any time.
Updates to this manual, technical clarification, and answers to frequently asked
questions will be shown on the following web site : http://www.portwell.com.tw/.

System Overview
PEB-2772AVGATM User’s Manual 1-1
Chapter 1
System Overview
1.1 Introduction
Portwell Inc., a world-leading innovator in the Industrial PC (IPC) market and a
member of the Intel® Embedded and Communications Alliance (Intel ECA),
announced today the Portwell PEB-2772 utilizing the Intel® ECX form
factor based on the Intel® Atom™ processor D2550 and the Intel® System
Controller Hub NM10, includes integrated, enhanced graphics and memory
controllers on 32nm process technology, delivering significant power reduction,
performance improvements and smaller platform footprint over the previous Intel®
Atom™ processor D525. The PEB-2772 can provide the low power
consumption for low profile fanless applications such as POS, Print Imaging, ATM,
Kiosk, Medical, Panel PC, Digital Security and Digital Signage.
PEB-2772 supports multi display by HDMI and VGA and 18/24-bit LVDS. With its
display-enriched interface, PEB-2772 can support various multimedia devices and
enriched IO interfaces that can supply various USB and COM devices.
PEB-2772 supports SO-DIMM memory slot for DDR3 SDRAM up
to 4GB, 4 x COM ports(1x Com port on rear IO/3x Com port on board header), 2
xSATA, 1 x Gigabit Ethernet, 6 x USB2.0 ports(1x USB port on rear IO/5x USB port on
board header). It also support one Mini-PCIE socket for embedded application usage.
1.2 Check List
The PEB-2772 package should cover the following basic items
9One PEB-2772VGATM 3.5’ Main Board
9One Thermal Kit
9One Serial ATA cable
9One SATA Power Y-cable
9One Installation Resources CD-Title
If any of these items is damaged or missing, please contact your vendor and keep all
packing materials for future replacement and maintenance.

System Overview
PEB-2772AVGATM User’s Manual 1-2
1.3 Product Specification
zMain Processor
- Intel®Atom™ D2550 dual-core processor
- CPU clock speed: 1.86GHz
zChipset
Intel®NM10 chipset
zSystem BIOS
Phoenix BIOS
zMain Memory
One 204 - pin DDR3 SODIMM socket support up to 4GB 800/1066 MHz memory
zExpansion Interface
One PCIex1
zSATA Interface
Two SATA ports (SATA 3Gb)
zSerial Port
- Support three RS232 com port(1x Com port on rear IO/2x Com port on board
header)
- Support one RS232/422/485 com port on board header
zUSB Interface
Support Sex USB (Universal Serial Bus) ports, one on rear I/O and five on board
header for internal devices
zAudio Interface
Connector for Line-Out(Line-out / Line-out / Mic-in pin header on board)
zReal Time Clock/Calendar (RTC)
Support Y2K Real Time Clock/Calendar
zWatch Dog Timer
- Support WDT function through software programming for enable/disable and
interval setting
- General system reset
zOn-board Ethernet LAN
One Gigabit Ethernet (10/100/1000 Mbits/sec) LAN ports
zHigh Drive GPIO
One pin-header for 8 bit GPIO (4bit in & 4bit out)

System Overview
PEB-2772AVGATM User’s Manual 1-3
zSystem Monitoring Feature
Monitor system temperature and major power sources.
zOutline Dimension (L x W)
146mm (5.75”) X 105mm (4.0”)
zPower Requirements
Configuration
1.4 System Configuration
System Configuration
CPU Type Intel (R) Atom(TM) CPU D2550 @1.86GHz FSB:533MHz
SBC BIOS Portwell, Inc.PEB-2772VGATM BIOS Rev.:R1.00.W3(07092012)
Memory Transcend DDR3 1066 SODIMM 2G(SEC HCH9K4B1G0846F)
VGA Card Onboard Intel® Graphics Media Accelerator 3600 Series
VGA Driver Intel® Graphics Media Accelerator 3600 Series Ver:8.14.8.1075
LAN Card Onboard Intel® 82583V Gigabit Network Connection
LAN Driver Intel® 82583V Gigabit Network Connection Ver:11.11.43.0
Audio Card Onboard Realtek ALC886 High Defintion Audio
Audio Driver Realtek High Defintion Audio Ver:6.0.1.6602
Chip Driver Intel® chipset Device software Ver:9.3.0.1019
SATA HDD Seagate ST3160318AS 160G
CDROM ASUS DRW-24B35T
Power Supply Seasonic SSA-0651-1 12V
zOperating Temperature
0 °C ~ 60 °C
zStorage temperature
-20 ~ 80 °C
zRelative Humidity
0% ~ 90%, non-condensing

System Overview
PEB-2772AVGATM User’s Manual 1-4
Mechanical Drawing

System Overview
PEB-2772AVGATM User’s Manual 1-5
1.5 System Architecture
All of details operating relations are shown in PEB-2772VGATM System Block
Diagram.
PEB-2772VGATM System Block Diagram

System Installation
PEB-2772AVGATM User’s Manual 2-1
Chapter 2
Hardware Configuration
This chapter gives the definitions and shows the positions of jumpers, headers and
connector. All of the configuration jumpers on PEB-2772VGTM are in the proper
position. The default settings are indicated with a star sign (★).
2.1 Jumper Setting
In general, jumpers on the single board computer are used to select options for certain features.
Some of the jumpers are designed to be user-configurable, allowing for system enhancement.
The others are for testing purpose only and should not be altered. To select any option, cover
the jumper cap over (SHORT) or remove (NC) it from the jumper pins according to the
following instructions. Here NC stands for “Not Connect”
Component side(Ver0.0)

System Installation
PEB-2772AVGATM User’s Manual 2-2
Solder side

System Installation
PEB-2772AVGATM User’s Manual 2-3
2.2 Connector Allocation
J1 USB (0-1) Connector (5*2-1 Pin Header/2.0mm)
J2 USB (2-3) Connector (5*2-1 Pin Header/2.0mm)
J3 SATA2 Connector
J4 SATA Power Output Connector (1*4 Pin Wafer/2.54mm)
J6 PS/2 Keyboard/Mouse Connector (1*6 Pin Wafer/2.0mm)
J7 RTC Battery Connector
J8 SATA1 Connector
J9 Hard disk LED Connector
J10 SM BUS signal connector
J11 CPU FAN Connector
J12 COM3 (RS-232) (2*5 Pin BOX Header/2.0mm)
J13 System Panel Connectors (2*4 Pin Header/2.0mm)
J14 Port 80 Connector (2x5-1(Pin 9) Pin Header/2.0mm)
J15 TPM Connector
J16 Reserve
J17 GPIO Connector (5*2 Pin BOX Header/2.0mm)
J18 COM4 (RS-232) (2*5 Pin BOX Header/2.0mm)
J19 COM2 (RS-232) (2*5 Pin BOX Header/2.0mm)
J20 MINI-PCI-E Connector
J21 LCD LVDS Connector (15*2 Pin Hirose)
J22 System FAN Connector
J23 Line-IN / Line-OUT/Microphone connector (4*2 Pin Header 2.0mm)
J24 +12V input Connector
J25 Reserve
J26 RJ45 LAN Connector
J27 HDMI and USB Connector
J28 Audio Jack(Audio out)
J29 Power Input Connector (Din Jack 3 Pin)
J30 VGA Connector
J31 COM1 (RS-232) (2*5 Pin BOX Header/2.0mm)
J32 USB (6) Connector (4*1 Pin Header/2.0mm)
JP1 Case open Connector
JP2 LCD Panel Voltage Setup (1*3 Pin Header/2.0mm)
JP3 LVDS Inverter Power Connector
JP4 CMOS Setup (1*3 Pin Header/2.0mm)
JP5 Panel voltage select(2*3Pin Header/2.0mm)
JP6 COM2 RI Function Setup (3x2 Pin Header/2.0mm)
JP7 COM1 RI Function Setup (3x2 Pin Header/2.0mm)
JP8 COM3 RI Function Setup (3x2 Pin Header/2.0mm)
JP9 COM4 RI Function Setup (3x2 Pin Header/2.0mm)
JP10 COM2 RS232/422/485 select header
SW1 LVDS GPIO SETUP

System Installation
PEB-2772AVGATM User’s Manual 2-4
Pin Assignments of Connectors
J1: USB (0-1) Connector (5*2-1 Pin Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 5V 2
5V
3 SB_D0- 4 SB_D1
5 SB_D0+ 6 SB_D1+
7 ND 8 ND
10
ND
J2: USB (2-3) Connector (5*2-1 Pin Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 5V 2
5V
3 SB_D2- 4 SB_D3
5 SB_D2+ 6 SB_D3+
7 ND 8 ND
10
ND
J3: SATA2 Connector)
PIN NO. DESCRIPTION
S1 GND
S2 TX+
S3 TX-
S4 GND
S5 RX-
S6 RX+
S7 GND
J4: SATA Power Output Connector (1*4 Pin Wafer/2.54mm)
PIN NO. DESCRIPTION
1 +12V
2 GND
3 GND
4 +5V
NOTES : Do not connect with two 3.5-inch HDD at the same time ,or the SATA Power
Connector will be overloaded.

System Installation
PEB-2772AVGATM User’s Manual 2-5
J6: PS/2 Keyboard/Mouse connector (1*6 Pin Wafer/2.0mm)
PIN NO. DESCRIPTION
1 K/B CLK
2 M/S DATA
3 K/B DATE
4 KB5V
5 M/S CLK
6 GND
J9: Hard disk LED Connector
PIN NO. DESCRIPTION
1 5V
2 Hard Disk signal
J10: SM BUS signal connector
PIN NO. DESCRIPTION
1 SM_CLK
2 NC(No Key)
3 GND
4 SM_DATA
5 5V
J11: CPU FAN Connector
PIN NO. DESCRIPTION
1 Fan Speed Detect
2 +12V
3 Fan Speed Driver
J12: COM3 (RS-232) (2*5 Pin BOX Header/2.0mm)
P
IN NO. DESCRIPTION
P
IN NO.
DESCRIPTION
1 DCD#3 2 DSR#3
3 RXD#3 4 RTS#3
5 TXD#3 6 CTS#3
7 DTR#3 8 V_RI3
9 GND 10 NC

System Installation
PEB-2772AVGATM User’s Manual 2-6
J13: System Panel Connectors (2*4 Pin Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 5VSB 2 SUSEND LED-
3 PWRLED+ 4 PWRLED-
5 GND 6 SYS_RESET#
7 PWR_ON_SW# 8 GND
J14: Port 80 Connector (2*5-1(Pin 9) Pin Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 LPC AD0 2 +3.3V
3 LPC AD1 4 RESET
5 LPC AD2 6 LPC FRAME
7 LPC AD3 8 LPC PCICLK
10 NC
J15: TPM Connector
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 PCLK_TPM 2 GND
3 LFRAME# 4 NC
5 PLT_RST# 6 VCC
7 LAD3 8 LAD2
9 VCC3 10 LAD1
11 LAD0 12 GND
13 SMB_CLK 14 SMB_DATA
15 3V_DUAL 16 SERIRQ
17 GND 18 NC
19 LPCPD# 20 NC
J16: Reserve
J17: GPIO Connector (5*2 Pin BOX Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 GPIO50 2 GPIO54
3 GPIO51 4 GPIO55
5 GPIO52 6 GPIO56
7 GPIO53 8 GPIO57
9 +5V 10 GND

System Installation
PEB-2772AVGATM User’s Manual 2-7
J18: COM4 (RS-232) (2*5 Pin BOX Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 DCD#4 2 DSR#4
3 RXD#4 4 RTS#4
5 TXD#4 6 CTS#4
7 DTR#4 8 V_RI4
9 GND 10 NC
J19: COM2 (RS-232) (2*5 Pin BOX Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 DCD#2 2 DSR#2
3 RXD#2 4 RTS#2
5 TXD#2 6 CTS#2
7 DTR#2 8 V_RI2
9 GND 10 NC
J20: MINI-PCI-E Connector
J21: LCD LVDS Connector (15*2 Pin Hirose)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
2 VDD_LVDS 1 VDD_LVDS
4 NC 3 NC
6 NC 5 NC
8 NC 7 NC
10 NC 9 NC
12 NC 11 NC
14 NC 13 NC
16 Ground 15 Ground
18 LCD_DO0- 17 LCD_DO0+
20 LCD_DO1- 19 LCD_DO1+
22 LCD_DO2- 21 LCD_DO2+
24 LCD_DO3- 23 LCD_DO3+
26 LCD_CLK- 25 LCD_CLK+
28 NC 27 NC
30 Ground 29 Ground
J22: System FAN Connector
PIN NO. DESCRIPTION
1 Fan Speed Detect
2 +12V
3 Fan Speed Driver

System Installation
PEB-2772AVGATM User’s Manual 2-8
J23: Line-IN / Line-OUT/Microphone connector (4*2 Pin Header 2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 MIC_L 2 Line in L
3 GND 4 Line in R
5 Line out L 6 GND
7 Line out R 8 MIC_R
J24: +12V input Connector)
PIN NO. Signal Description
1 GND
2 GND
3 +12V
4 +12V
J25: Reserve
J26: RJ45 LAN Connector
J27: HDMI and USB Connector)
J28: Audio Jack(Audio out)
J29: Power Input Connector (Din Jack 3 Pin)
PIN NO. DESCRIPTION
1 VIN
2 GND
3 GND
CG1 GND
J30: VGA Connector
J31: COM1 (RS-232) (2*5 Pin BOX Header/2.0mm)
PIN NO. DESCRIPTION PIN NO.
DESCRIPTION
1 DCD#2 2 DSR#2
3 RXD#2 4 RTS#2
5 TXD#2 6 CTS#2
7 DTR#2 8 V_RI2
9 GND 10 NC

System Installation
PEB-2772AVGATM User’s Manual 2-9
J32: USB(6) Connector(4*Pin Header/2.0mm)
PIN NO. DESCRIPTION
1 +5V
2 USB_D6-
3 USB_D6+
4 GND
JP1: Case open Connector)
PIN NO. DESCRIPTION
1 CASEOP#
2 GND
JP2: LCD Panel Voltage Setup (1*3 Pin Header/2.0mm)
PIN NO. DESCRIPTION
1-2 2-3
Short +1.8V (Scaler)★
Short +2.5V(Bypass)
JP3: LVDS Inverter Power Connector
PIN NO. DESCRIPTION
1 VCC5_PS
2 NC(No Key)
3 +12V
4 GND
5 BKLTEN
JP4: CMOS Setup (1*3 Pin Header/2.0mm)
PIN NO. DESCRIPTION
1-2 Normal (Keep CMOS Setup) ★
2-3 Clear CMOS Setup
JP5: Panel voltage select(2*3Pin Header/2.0mm)
PIN NO. DESCRIPTION
2-4 4-6 3-4
Short +3.3V TFT LCD
Short
+5V TFT LCD ★
Short +12V TFT LCD

System Installation
PEB-2772AVGATM User’s Manual 2-10
JP6/JP7/JP8/JP9:COM RI Function Setup (3*2 Pin Header/2.0mm)
PIN NO. DESCRIPTION
1-2 3-4 5-6
Short +5V Output
Short RI Function ★
Short +12V Output
NOTES:COM1 (J31/JP7), COM2(J19/JP6), COM3(J12/JP8), COM4(J18/JP9)
JP10: COM2 RS232/422/485 select header
PIN NO. DESCRIPTION
5-6 9-11 10-12 15-17 16-18 Other
Short Short Short Short Short Open RS-232 Function★
PIN NO. DESCRIPTION
3-4 7-9 8-10 13-15 14-16 21-22 Other
Short Short Short Short Short Short Open RS-422 Function
PIN NO. DESCRIPTION
1-2 7-9 8-10 19-20 Other
Short Short Short Short Open RS-485 Function
SW1: LVDS GPIO SETUP
Action GPIO Status
Short 0
Open 1
SW1 Pin Number Single Description
1、2 GPIO0
3、4 GPIO1
5、6 GPIO2
7、8 GPIO3
The default of GPIO：
GPIO3 GPIO2 GPIO1 GPIO0
0 1 1 0

System Installation
PEB-2772AVGATM User’s Manual 2-11

System Installation
PEB-2772AVGATM User’s Manual 3-1
Chapter 3
System Installation
This chapter provides you with instructions to set up your system. The additional
information is enclosed to help you set up onboard PCI device and handle Watch Dog
Timer (WDT) and operation of GPIO in software programming.
3.1 Intel ® Atom TM Processor D2550
Passively-cooled, soldered-down Dual-Core Intel ® Atom™ processor D2550 with
integrated graphics and integrated memory controller that’s suitable for fanless
system and low-watt design.
3.2 Main Memory
PEB-2772 provide 1 x 204-pin SO-DIMM sockets which supports 1066 DDR3-SDRAM
as main memory, Non-ECC (Error Checking and Correcting), non-register functions.
The maximum memory size can be up to 4GB capacity. Memory clock and related
settings can be detected by BIOS via SPD interface.
Watch out the contact and lock integrity of memory module with socket, it will
impact on the system reliability. Follow normal procedures to install memory module
into memory socket. Before locking, make sure that all modules have been fully
inserted into the card slots.
Note: DDR3 1333 MHz and DDR3 1600 MHz memory will run at 1066 MHz
3.3 Installing the Single Board Computer
To install your PEB-2772 into standard chassis or proprietary environment, please
perform the following:
Step 1 : Check all jumpers setting on proper position
Step 2 : Install memory module onto memory socket
Step 3 : Place PEB-2772 into the dedicated position in the system
Step 4 : Attach cables to existing peripheral devices and secure it
WARNING
Please ensure that SBC is properly inserted and fixed by mechanism.
Note: