Portwell ROBO-8713 Series User manual

ROBO-8713 Series
Single Board Computer
User's Manual
P/N: B8980050 Version 1.1
Copyright © Portwell, Inc., 2005. All rights reserved.
All other brand names are registered trademarks of their respective owners.
StockCheck.com

Preface
Table of Contents
How to Use This Manual
Chapter 1 System Overview ...................................................................................................................... 1-1
1.1 Introduction................................................................................................................................................... 1-1
1.2 Check List....................................................................................................................................................... 1-2
1.3 Product Specification.................................................................................................................................... 1-3
1.3.1 Mechanical Drawing.......................................................................................................................... 1-5
1.4 System Architecture...................................................................................................................................... 1-6
Chapter 2 Hardware Configuration........................................................................................................... 2-1
2.1 Jumper Setting............................................................................................................................................... 2-1
2.2 Connector Allocation.................................................................................................................................... 2-3
Chapter 3 System Installation ................................................................................................................... 3-1
3.1 Socket 478 Pentium 4/Celeron Processor.................................................................................................. 3-1
3.2 Main Memory................................................................................................................................................ 3-2
3.3 CompactFlash Card ...................................................................................................................................... 3-3
3.4 Installing the Single Board Computer........................................................................................................ 3-4
3.4.1 Chipset Component Driver............................................................................................................... 3-4
3.4.2 ATI Mobility Radeon Graphic Integrated Chipset ........................................................................ 3-4
3.4.3 Intel Integrated Graphics GMCH Chip (For ROBO-8713VGA only) .......................................... 3-5
3.4.4 Gigabit Ethernet Controller .............................................................................................................. 3-5
3.4.5 On-board AC-97 Audio Device........................................................................................................ 3-6
3.4.6 On-board 68-pin PCI connector ....................................................................................................... 3-6
3.5 Clear CMOS Operation ................................................................................................................................ 3-6
3.6 WDT Function ............................................................................................................................................... 3-7
3.7 SMBus............................................................................................................................................................. 3-8
3.8 On-Board USB 2.0 Controller ...................................................................................................................... 3-8
3.9 Display Output (For ROBO-8713UGA, ROBO-8713SGA only) .............................................................. 3-9
3.10 GPIO ............................................................................................................................................................. 3-9
3.10.1 Pin assignment ................................................................................................................................. 3-9
3.10.2 ROBO-8713 GPIO Programming Guide...................................................................................... 3-10
3.10.3 Example........................................................................................................................................... 3-11
Chapter 4 BIOS Setup Information ........................................................................................................... 4-1
4.1 Entering Setup............................................................................................................................................... 4-1
4.2 Main Menu..................................................................................................................................................... 4-2
4.3 Standard CMOS Setup Menu...................................................................................................................... 4-3
4.4 IDE Adaptors Setup Menu .......................................................................................................................... 4-5
4.5 Advanced BIOS Features ............................................................................................................................. 4-7
4.6 Advanced Chipset Features....................................................................................................................... 4-10
4.7 Integrated Peripherals ................................................................................................................................ 4-14
4.8 Power Management Setup......................................................................................................................... 4-20
4.9 PnP/PCI Configurations............................................................................................................................ 4-24
4.10 PC Health Status ....................................................................................................................................... 4-27
4.11 Frequency/Voltage Control .................................................................................................................... 4-28
4.12 Default Menu............................................................................................................................................. 4-28
4.13 Supervisor/User Password Setting ........................................................................................................ 4-29
4.14 Exiting Selection........................................................................................................................................ 4-30
Chapter 5 Troubleshooting ....................................................................................................................... 5-1
5.1 Hardware Quick Installation....................................................................................................................... 5-1
5.2 BIOS Setting................................................................................................................................................... 5-6
5.3 FAQ................................................................................................................................................................. 5-8
Appendix A
Appendix B
StockCheck.com

Preface
How to Use This Manual
The manual describes how to configure your ROBO-8713 series system to meet
various operating requirements. It is divided into five chapters, with each chapter
addressing a basic concept and operation of Single Board Computer.
Chapter 1 : System Overview. Presents what you have in the box and give you an
overview of the product specifications and basic system architecture for this series
model of single board computer.
Chapter 2 : Hardware Configuration. Shows the definitions and locations of
Jumpers and Connectors that you can easily configure your system.
Chapter 3 : System Installation. Describes how to properly mount the CPU, main
memory and Compact Flash to get a safe installation and provides a programming
guide of Watch Dog Timer function.
Chapter 4 : BIOS Setup Information. Specifies the meaning of each setup
parameters, how to get advanced BIOS performance and update new BIOS. In
addition, POST checkpoint list will give users some guidelines of trouble-shooting.
Chapter 5 : Troubleshooting. Provides various useful tips to quickly get ROBO-8713
series running with success. As basic hardware installation has been addressed in
Chapter 3, this chapter will basically focus on system integration issues, in terms of
backplane setup, BIOS setting, and OS diagnostics.
The content of this manual and EC declaration document is subject to change
without prior notice. These changes will be incorporated in new editions of the
document. Portwell may make supplement or change in the products described in
this document at any time.
Updates to this manual, technical clarification, and answers to frequently asked
questions will be shown on the following web site : http://www.portwell.com/.
StockCheck.com

Preface
EC Declaration of Conformity
(To Be Added)
For the following equipment:
Product Name:
Model Name:
Trade Name:
is herewith confirmed to comply with the requirements set out in the Council
Directive on the Approximation of the Laws of the Member States relating to
Electromagnetic Compatibility Directive (89/336/EEC). The equipment was
evaluated and passed the test, the following standards were applied :
EMC : EN 55022 (1994/A1:1995 Class A)
EN 50082-2 (1991)
EN 61000-4-2 (1995)
EN 61000-4-3 (1996)
EN 61000-4-4 (1995)
EN 61000-3-2 (1995)
EN 61000-3-3 (1995)
The following manufacturer is responsible for this declaration :
Portwell, Inc.
(Company Name)
3F, No.88, Sec.1, Nei-Hu Rd., Taipei, Taiwan, R.O.C.
(Company Address)
Taipei, R.O.C.
Place Date Legal Signature of
Authorized Person
StockCheck.com

Preface
 Remove Processor
Caution: Do not pull out processor without opening socket handle!
 High viscosity thermal grease between processor and cooler will lead the processor be
pulled out from socket when taking cooler off.
 This action may damage processor socket, which will cause poor contact between CPU
& socket.
 Handling SBC
Caution: Do not just hold any single side of the SBC; hold evenly on both sides!
 Heavy processor cooler shall bend the SBC when SBC being held just on one side.
 The bending may cause serious soldering or circuit damage.
WARNING
StockCheck.com

System Overview
ROBO-8713 Series User’s Manual 1-1
Chapter 1
System Overview
1.1 Introduction
The ROBO-8713 series all-in-one full size single board computer is designed to fit
high performance and scalable Intel®Pentium®4/Celeron processors and
compatible for high-end industrial computer system with PCI plus ISA local bus
architecture (PICMG 1.0 Rev 2.0). It is made to meet today’s demanding reliability &
stability for critical computing environments, and keep complete compatibility &
functionality for wide range of applications. It’s beneficial to built up a high
performance and reliable system for VARs, or system integrators. The on-board 3D
ATI-Mobility Radeon graphics (ROBO-8713UGA/SGA) with panel display interface
and TV output interface, Intel “Communication Streaming Architecture” Gigabit
Ethernet interface and AC-97 audio CODEC will bring full functionality and high
performance to all segments of the industrial PC market.
This single board computer runs with Intel®Pentium®4/Celeron (mPGA478)
processor, and supports two DIMM up to 2GB DDR SDRAM maximum. The
enhanced on-board PCI IDE interface can support 4 drives up to PIO mode 4 timing
and Ultra DMA/33/66/100 synchronous mode feature. The on-board Super I/O
Chipset integrates one floppy controller, two serial ports, one keyboard controller,
hardware monitoring, one IrDA port and one parallel port. Besides, three USB
(Universal Serial Bus) ports provide high-speed data communication between
peripherals and PC.
Its proprietary PCI extension connector provides an easy way to add additional
functions like U160 SCSI, 2nd or 3rd LAN device in minutes. The compact form factor
with proprietary PCI connection interface makes it the best and flexible daughter
board solution for adding more functions in a limited space.
The PICMG standard makes the ROBO-8713 series works with the legacy ISA,
ISA/PCI or multi-slots PCI-bus backplane. The on-board type II CF socket supports
CompactFlash card up to 1GB. The Watch-Dog Timer function can be used to
restart you system whenever system goes abnormal. One 6-pin Mini-DIN connector
(with Y-Cable) is provided to connect PS/2 Keyboard and Mouse. The on-board
Flash ROM is used to make the BIOS update easier, ROM chip can be replaced
quickly. The ROBO-8713 series also provide up to 8 programmable high driving
GPIO and high-resolution watchdog timer. All of these features make ROBO-8713
series excellent in many applications and one of the best performing single board
computer in the market.
StockCheck.com

System Overview
ROBO-8713 Series User’s Manual 1-2
Notice for users of ROBO-8713 series:
Its graphic engine classifies ROBO-8713 series. Following table helps identify the
ROBO-8713 series.
Model Name ATi
Mobility M10
ATi
Mobility M9
GMCH Integrated
Graphics
ROBO-8713UGA Inte
g
rated 64MB
Video Memory --- ---
ROBO-8713SGA ---
Integrated 32MB
Video Memory ---
ROBO-8713VGA --- ---
Shared System Memory
Up to 64MB
1.2 Check List
The ROBO-8713 series package should cover the following basic items:
 One ROBO-8713UGA, SGA or VGA single board computer
 One dual Serial ports cable kit
 One Parallel port cable kit (2.0mm pitch)
 One FDC cable (2.0mm pitch)
 One IDE cable
 One Y-cable cable for PS/2 keyboard and mouse
 One 4-pin ATX power control cable for backplane connection
 One 7-pin SATA signal cable
 One Installation Resources CD-Title
 One booklet of ROBO-8713 series manual
If any of these items is damaged or missing, please contact your vendor and keep all
packing materials for future replacement and maintenance.
StockCheck.com

System Overview
ROBO-8713 Series User’s Manual 1-3
1.3 Product Specification
 Main processor
- Intel®Pentium®4/Celeron Processor
- FSB: 800/533/400MHz
 BIOS
Phoenix (Award) system BIOS with 4Mb Flash ROM with easy upgrade function
ACPI, DMI, Green function and Plug and Play Compatible
 Main Memory
- Support dual-channel & signal channel DDR memory interface
- Non-ECC, non-buffered DIMMS only
- Two DIMM sockets support 266/333/400 DDR-SDRAM up to 2GB System
Memory
 L2 Cache Memory
512/256KB in Intel®Pentium®4/Celeron Processor
 Chipset
Intel 865 GMCH/MCH and ICH5 chipset
 Bus Interface
- Follow PICMG 1.0 Rev 2.0 standard (32-bit PCI and 16-bit ISA)
- Fully complies with PCI Local Bus specification V2.2 (support 4 master PCI
slots)
 PCI IDE Interface
Support two enhanced IDE ports up to four HDD devices with PIO mode 4 and
Ultra DMA/33/66/100 mode transfer and Bus Master feature
 Floppy Drive Interface
Support one FDD port up to two floppy drives and 5-1/4"(360K, 1.2MB), 3-1/2"
(720K, 1.2MB, 1.44MB, 2.88MB) diskette format and 3-mode FDD
 Serial Ports
Support two high-speed 16C550 compatible UARTs with 16-byte T/R FIFOs
 IR Interface
Support one 6-pin header for serial Standard Infrared wireless communication
 Parallel Port
Support one parallel port with SPP, EPP and ECP modes
 USB Interface
Support four USB (Universal Serial Bus) ports for high-speed I/O peripheral
devices
 PS/2 Mouse and Keyboard Interface
Support one 6-pin Mini-DIN connector for PS/2 keyboard/mouse connection
through Y-Cable separation and one 5-pin shrouded connector for PS/2
keyboard connection through backplane connection
StockCheck.com

System Overview
ROBO-8713 Series User’s Manual 1-4
 ATX Power Control Interface
One 4-pin header to support ATX power control with Modem Ring-On and
Wake-On-LAN function
 Auxiliary I/O Interfaces
System reset switch, external speaker, Keyboard lock and HDD active LED, etc
 Real Time Clock/Calendar (RTC)
Support Y2K Real Time Clock/Calendar with battery backup for 7-year data
retention
 Watchdog Timer
- Support WDT function through software programming for enable/disable and
interval setting
- Generate system reset
 CompactFlash
- True IDE mode, compatibles with the ATA/ATAPI-4 specification
- One Type II CF socket on secondary IDE channel for supporting up to 1GB
memory
- Bootable for no drives on primary channel
 On-board VGA
- ATI-Mobility M10 (ROBO-8713UGA)/M9 (ROBO-8713SGA) graphic controller
works in combination with a 64/32MB DDR-SDRAM
- Support Dual channel LVDS interface (ROBO-8713UGA/SGA)
- Support TMDS interface for DVI display (ROBO-8713UGA/SGA)
- Support TV output (ROBO-8713UGA/SGA)
- GMCH integrated graphics, 266MHz core frequency; share system memory up
to 64MB for system with greater than or equal to 192MB of system memory
(ROBO-8713VGA)
 On-board Ethernet LAN
Intel 82547 integrated LAN controller to support RJ-45 connector
 On-board 68-pin PCI connector
Support one additional PCI daughter board
 High ISA Driving Capability
Support 64mA high driving capability for multi-slots ISA-bus
 High Driving GPIO
Support 8 programmable high driving GPIO
 Cooling Fans
Support three 3-pin headers for CPU, System and Power fans
 System Monitoring Feature
Monitor CPU temperature, system temperature and major power sources, etc
 Bracket
Support one Ethernet port with 2 indicators, dual USB ports, one Mini-DIN port
for PS/2 keyboard/mouse, and one CRT port
StockCheck.com

System Overview
ROBO-8713 Series User’s Manual 1-5
 Outline Dimension (L X W):
338.5mm (13.33”) X 122mm (4.8”)
 Power Requirements:
 Configuration A:
- +12V (CPU) @5.2A
- +12V (System) @0.8A
- +5V @7.0A
- Test configuration:
•CPU: Intel Pentium 4 - 3GHz/800MHz FSB/512KB L2 Cache
•Memory: DDR SDRAM 512MBx2
•Primary Master IDE HDD: Maxtor-6Y120L0
•OS: Microsoft Windows 2000 Professional + SP4
•Test Programs: 3D Mark 2001 PRO for loading VGA and Burning Test V3.0
for loading CPU
•Connected Fans: Only CPU fan connected
•Run Time: 10 minutes
 Operating Temperature:
-5°C ~ 60°C (23°F ~ 140°F)
 Storage Temperature:
-20°C ~ 80°C
 Relative Humidity:
0% ~ 95%, non-condensing
1.3.1 Mechanical Drawing
StockCheck.com

System Overview
ROBO-8713 Series User’s Manual 1-6
1.4 System Architecture
The most up-to-date system architecture of ROBO-8713 series includes two main
Intel®chips - Intel 865 chipset supports Pentium-4 processor, DDR-SDRAM, 2D/3D
graphic display, and 82801EA ICH5 that supports PCI bus interface, APM, ACPI
compliant power management, USB port, SMBus communication, and Ultra
DMA/33/66/100 IDE Master. Super I/O chip W83627HF is responsible for PS/2
Keyboard/Mouse, UARTs, FDC, Hardware Monitor, Parallel, Watch Dog Timer and
Infrared interface.
The PCI-to-ISA Bridge supports a standard 16-bit ISA bus interface that is applied
for all slower I/O operations. In ROBO-8713 series, they support IDE mode
CompactFlash Flash disk.
There is one on-board Gigabit Ethernet via RJ-45 Port to support full functionality of
ROBO-8713 series AIO SBC (All-In-One Single Board Computer). The on-board 68-
pin PCI connector supports one additional PCI daughter board for further extension.
StockCheck.com

System Overview
ROBO-8713 Series User’s Manual 1-7
Dual-Channel DIMM*2
DDR 266/333/400
I/O Controller Hub
ICH5 (82801EB)
VGA CONN
Prescott or Northwood
mPGA478B Socket
CY28409
SPRINGDALE
GMCH/MCH
LVDS CONN
VRD 10.0
TMDS CONN
TV CONN
Giga CSA LAN
828547EI
ADDR
CTRL
DATA
ADDR
CTRL
DATA
DVO CONN
IDE Primary
IDE Secondary
Compact Flash
USB Port 1
PCI BUS ISA BUS
PCI ADDR/DATA
PCI CTRL
LCI
ISA ADDR/DATA
ISA CTRL
PCI to ISA
IT8888
USB Port 2
USB Port 3
USB Port 4
Audio Codec
Winbond
W83627F/HF
LPC SIO
F/W HUB
KEYBOARD
MOUSE
FLOPPY PARALLEL SERIAL 1/2
LPC BUS
Hub Link 1.5
AGP BUS
Ultra
DMA33/66/100
SATA Interface
USB 2.0/1.1
AC` 97 LINK
SATA X2
HOST BUS
M10/M9
ROBO-8713 System Block Diagram
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-1
Chapter 2
Hardware Configuration
This chapter gives the definitions and shows the positions of jumpers, headers and
connector. All of the configuration jumpers on ROBO-8713 series are in the proper
position. The default settings shipped from factory are marked with a star (Ì).
2.1 Jumper Setting
Figure 2-1 ROBO-8713 Jumper Location
JP1: AT/ATX Power Selection
JP1 Function
1-3, 2-4 Short AT Power
3-5, 4-6 Short ATX Power Ì
Note:
JP4 must be set 2-3 short first then Return 1-2 short \to clear CMOS RAM if JP1 has
been changed ever.
J
P1
1
2
5
6
J
P2
J
P3
11
222
21
216
15
J
P4
13
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-2
JP2: COM2 (J26) Interface Selection
JP2 Function
5-6, 9-11, 10-12, 15-17, 16-18 Short RS-232 Ì
3-4, 7-9, 8-10, 13-15, 14-16, 21-22 Short RS-422
1-2, 7-9, 8-10, 19-20 Short RS-485
JP3: LVDS Backlight-On Signal Selection (Pin 1~Pin 6)
JP3 (1~6) Function
1-2, 4-6 Short 5V, Active Low
1-2, 5-6 Short 5V, Active High Ì
1-3, 4-6 Short 12V, Active Low
1-3, 5-6 Short 12V, Active High
* Only for ROBO-8713SGA/UGA
JP3: LVDS Panel Power (VDD) Selection (Pin 7~Pin 10)
JP3 (7~10) Function
7-8 Short 5V
9-10 Short 3.3V Ì
* Only for ROBO-8713SGA/UGA
JP3: LVDS Resolution Selection (Pin 11~Pin 16)
JP3 (11~16) Function
Pin 11-16 Open LVDS Disable Ì
11-12 Short ID0 (1024*768, 18 Bits)
13-14 Short ID1 (800*600, 18 Bits)
11-12, 13-14 Short ID2 (1024*768, 36 Bits)
15-16 Short ID3 (1024*768, 24 Bits)
* Only for ROBO-8713SGA/UGA
Note:
Enable TMDS signal by setting LVDS disabled, Pin 11~ Pin 16 Open.
JP4: CMOS Clear
JP4 Function
1-2 Short Normal Operation Ì
2-3 Short Clear CMOS Contents
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-3
2.2 Connector Allocation
I/O peripheral devices are connected to the interface connectors on this Embedded
ATX computer.
Figure 2-1 ROBO-8713 Connector Location (Component Side)
J
1
1
2
3
4
J
36
J
40
J
41
1
311
33
J
34 1
2
67
68
J
2
J
3
J
4
J
5
11 11
J
18
J
6
1
J
8
J
9
139
2
J
21
J
20
71
J
17
J
19
1
1
J
7
11
19
19
2
20
20
J
22
J
23
1
1
J
43
J
45
1
2
10
1
J
44
9
2
10
9
J
25
J
24
J
29
J
30
1
1
1
12
910
1
5
11
15
1
2
5
41
1
4
8
1
J
31
J
32
J
33
J
35
J
46
6
10
5
J
12
J
14
J
26
J
27
J
28
J
16
1
1
J
10
J
13
11
6
1
6 10
15
J
15
1
2
26
13
6
1
14
1
5
1
34
33
J
11
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-4
Figure 2-2 ROBO-8713 Connector Location (Solder Side)
Connector Function List
Connector Description Remark (Model)
J
1 12V POWER Connector
J
2 Reset Button Connector
J
3 External S
p
eaker Connector
J
4 Power LED and Ke
y
board Lock Connector
J
5 Hard Disk Drive LED Connector
J
6 Standalone Power Connector
J
7 ATX Power Control Connector
J
8 Primar
y
IDE Connector
J
9 Secondar
y
IDE Connector
J
10 SMBus Connector
J
11 Parallel Port Connector
J
12 FDC Interface Connector
J
13 IrDA Connector
J
14 TV-out Connector Only for ROBO-8713SGA/UGA
J
16 LVDS Panel Control Connector Only for ROBO-8713SGA/UGA
J
17 LVDS Panel Connector Only for ROBO-8713SGA/UGA
J
18 ATX Power button Inter
f
ace
J
19 TMDS Panel Connect Only for ROBO-8713SGA/UGA
J
20 Secondar
y
SATA Connector
J
21 Primar
y
SATA Connector
J
22 External Wake On Rin
g
Connector
J
23 External Wake On LAN Connector
J
24 External Thermal Sensor Connector
J
25 General Pur
p
ose I
/
O Connector
J
26 COM2 Serial Port 2 Connector
J
27 COM1 Serial Port 1 Connector
J
28 External Ke
y
board Connector
J
47
50
1
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-5
J29
Case
-
open Detection Connector
J
30 External LAN Access LED Connector
J
31 Ethernet R
J
-45 Connector
J
32 Primar
y
USB Connector
J
33 Secondar
y
USB Connector
J
34 68-
p
in PCI Connector
J
35 PS
/
2 Ke
y
board
/
Mouse Connector
J
36 FAN 3
(
CPU FAN
)
J
40 FAN 2
(
POWER FAN
)
J
41 FAN 1
(
SYSTEM FAN
)
J
43 External USB Connector
J
44 Audio CD-in Connector
J
45 Audio MIC
/
Line-in
/
Line-out Connector
J
46 On-board VGA CRT Connector
J
47 Com
p
act Flash Card
Pin Assignments of Connectors
J1: 12V POWER Connector
PIN No. Signal Description
1 Ground
2 Ground
3 +12V
4 +12V
J2: Reset Button Connector
PIN No Signal Description
1 Reset Signal Input (Active low)
2 Ground
J3: External Speaker Connector
PIN No. Signal Description
1 Speaker Signal Output (Open-drain w/
internal series 33 Ohm)
2 N/C
3 Ground
4 +5V
Note:
The pull-high voltage of external speaker is limited at 5V maximum.
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-6
J4: Power LED and Keyboard Lock Connector
PIN No. Signal Description
1 +5V (330 Ohm pull-up for power LED+)
2 N/C
3 Ground (For Power LED-)
4 Keyboard Lock Signal Input (Active low)
5 Ground
J5: Hard Disk Drive LED Connector
PIN No. Signal Description
1 +5V (270 ohm pull-up for HDD LED+)
2 HDD Active # (HDD LED-)
J6: Standalone Power Connector
PIN No. Signal Description
1 +12V
2 Ground
3 Ground
4 +5V
Notes:
1) To run system in standalone operation. Both J1 and J6 have to be connected.
2) Some of USB 2.0 devices need large current consumption. It is helpful for them
to detect by system while Standalone Power connector is connected on SBC.
J7: ATX Power Control Connector
PIN No. Signal Description
1 ATX Power Good Signal (PW-OK)
2 ATX 5V Stand-by (5VSB)
3 ATX Power On Control (PS-ON)
4 Ground
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-7
J8/J9 Primary/Secondary IDE Connector (IDE1/IDE2)
PIN No. Signal Description PIN No. Signal Description
1 RESET# 2 Ground
3 Data 7 4 Data 8
5 Data 6 6 Data 9
7 Data 5 8 Data 10
9 Data 4 10 Data 11
11 Data 3 12 Data 12
13 Data 2 14 Data 13
15 Data 1 16 Data 14
17 Data 0 18 Data 15
19 Ground 20 N/C
21 DMA REQ 22 Ground
23 IOW# 24 Ground
25 IOR# 26 Ground
27 IOCHRDY 28 Pull-down
29 DMA ACK# 30 Ground
31 INT REQ 32 N/C
33 SA1 34 CBLID#
35 SA0 36 SA2
37 HDC CS0# 38 HDC CS1#
39 HDD Active# 40 Ground
J10: SMBus Connector
PIN No. Signal Description
1 SMBus Clock
2 N/C
3 Ground
4 SMBus Data
5 +3V
StockCheck.com

Hardware Configuration
ROBO-8713 Series User’s Manual 2-8
J11: Parallel Port Connector
PIN No. Signal Description PIN No. Signal Description
1 Strobe# 14 Auto Form Feed#
2 Data 0 15 Error#
3 Data 1 16 Initialization#
4 Data 2 17 Printer Select IN#
5 Data 3 18 Ground
6 Data 4 19 Ground
7 Data 5 20 Ground
8 Data 6 21 Ground
9 Data 7 22 Ground
10 Acknowledge# 23 Ground
11 Busy 24 Ground
12 Paper Empty 25 Ground
13 Printer Select 26 N/C
J12: FDC Interface Connector
PIN No. Signal Description PIN No. Signal Description
1 Ground 2 Density Select 0
3 Ground 4 N/C
5 Ground 6 Density Select 1
7 Ground 8 Index#
9 Ground 10 Motor ENA#
11 Ground 12 Drive Select B#
13 Ground 14 Drive Select A#
15 Ground 16 Motor ENB#
17 Ground 18 Direction#
19 Ground 20 Step#
21 Ground 22 Write Data#
23 Ground 24 Write Gate#
25 Ground 26 Track 0#
27 Ground 28 Write Protect#
29 Ground 30 Read Data#
31 Ground 32 Head Select#
33 Ground 34 Disk Change#
StockCheck.com