POS-X EVO TP6W User manual

EVO TP6W
All in One POS Terminal
User Manual v1.0

ii
Copyright 2020
All Rights Reserved
Manual Version 1.0
The information contained in this document is subject to change without notice.
We make no warranty of any kind with regard to this material, including, but not limited
to, the implied warranties of merchantability and fitness for a particular purpose.
We shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved. No part of this document may be photocopied, reproduced or translated
to another language without the prior written consent of the manufacturer.
TRADEMARK
Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation.
Other trademarks mentioned herein are the property of their respective owners.
Safety
IMPORTANT SAFETY INSTRUCTIONS
1. To disconnect the machine from the electrical power supply, turn off the power switch
and remove the power cord plug from the wall socket. The wall socket must be easily
accessible and in close proximity to the machine.
2. Read these instructions carefully. Save these instructions for future reference.
3. Follow all warnings and instructions marked on the product.
4. Do not use this product near water.
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation
to ensure reliable operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This product should
never be placed near or over a radiator or heat register or in a built-in installation
unless proper ventilation is provided.
7. This product should be operated from the type of power indicated on the marking label.
If you are not sure of the type of power available, consult your dealer or local power
company.
8. Do not allow anything to rest on the power cord. Do not locate this product where
persons will walk on the cord.
9. Never push objects of any kind into this product through cabinet slots as they may
WRXFKGDQJHURXVYROWDJHSRLQWVRUVKRUWRXWSDUWVWKDWFRXOGUHVXOWLQDÀUHRUHOHFWULF
shock. Never spill liquid of any kind on the product.

iii
CE MARK
This device complies with the requirements of the EEC directive 2014/30/EU with
regard to “Electromagnetic compatibility” and 2014/35/EU “Low Voltage Directive”.
FCC
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION ON LITHIUM BATTERIES
There is a danger of explosion if the battery is replaced incorrectly. Replace only
with the same or equivalent type recommended by the manufacturer. Discard used
batteries according to the manufacturer’s instructions.
Battery Caution
Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery
according to the local disposal instructions.
Safety Caution
Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related
OHJLVODWLRQSHULSKHUDOVVKDOOEH´0DWHULDOVIRUÀUHHQFORVXUHµFRPSOLDQW
0DWHULDOVIRUÀUHHQFORVXUHV
For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a
),5((1&/2685(LQWKHWKLQQHVWVLJQLÀFDQWZDOOWKLFNQHVVXVHGVKDOOEHRI9&/$66
MATERIAL or shall pass the test of Clause A.2.
For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all STATIONARY
EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest significant wall
thickness used, shall be of 5VB CLASS MATERIAL or shall pass the test of Clause A.1

iv
LEGISLATION AND WEEE SYMBOL
2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment,
collection, recycling and disposal of electric and electronic devices and their
components.
The crossed dust bin symbol on the device means that it should not be disposed of
with other household wastes at the end of its working life. Instead, the device should
be taken to the waste collection centers for activation of the treatment, collection,
recycling and disposal procedure.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product,
RUWKHLUORFDOJRYHUQPHQWRIÀFHIRUGHWDLOVRIZKHUHDQGKRZWKH\FDQWDNHWKLVLWHPIRU
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of
the purchase contract.
This product should not be mixed with other commercial wastes for disposal.

v
Revision Description Date
1.0 • Initial release January 2020
Revision History
Changes to the original user manual are listed below:

vi
Table of Contents
1. Packing List..................................1
1-1. Standard Accessories.....................................................1
1-2. Optional Accessories.......................................................2
2. System View..................................3
2-1. Front & Side View............................................................3
2-2. Rear View.........................................................................3
2-3. IO Ports View....................................................................4
2-4. System Dimensions ........................................................5
3. System Assembly & Disassembly6
3-1. Disassemble the Stand ..................................................6
3-2. Remove the Cable Cover ................................................6
3-4. Install the Power Adapter................................................7
3-3. Replace HDD...................................................................7
4. Peripheral Installation.................8
4-1. Install the MSR Module..................................................8
4-2. Install the Fingerprint Module........................................9
4-3. Install the Customer Display .........................................10
4-4. Install the Second Display ............................................11
4-5. Cash Drawer Installation ..............................................12

vii
 6SHFLÀFDWLRQ................................ 14
 &RQÀJXUDWLRQ............................... 16
6-1. D86U Motherboard ......................................................16
6-1-1. Motherboard Layout.......................................................... 16
6-1-2. Connectors & Functions .................................................17
6-1-3. Jumper Setting ................................................................18

viii
The page is intentionally left blank.

a. System
b. Power adapter
c. Power cord
d. RJ45-DB9 cable (x2)
1. Packing List
1-1. Standard Accessories
ab
cd
1

a. MSR
b. Fingerprint reader
c. LCD 2nd display
d. 2-line Customer display
1-2. Optional Accessories
ab
cd
2

2. System View
2-1. Front & Side View
No. Description
1 Touch screen
2 Fingerprint (option)
3 MSR (option)
4 Power button
5 Stand front cover
6 Stand
2-2. Rear View
No. Description
1 VESA top cover
2 Cable cover
1
23
45
6
1
2
3

2-3. IO Ports View
D86U Motherboard
No. Description
a
bHDD slot
cPower button
dDC19Vin
eVGA
fCOM 1, 2, 3 (from right to left)
gLAN
hUSB 2.0 x 2
iCash drawer
USB 3.0 x 4
ab c def g h
i
4

2-4. System Dimensions
18.1"
8.5"
19.9"
11.6
8"
5

3. System Assembly & Disassembly
3-1. Disassemble the Stand
3-2. Remove the Cable Cover
1. Loosen the thumb screw (x1) and
slide the stand towards the IO panel
to release it from the system.
2. Reverse the steps above to attach
stand to the system.
1. Pull the cable cover upwards to
release it from the system.
6

3-3. Replace HDD
3-4. Install the Power Adapter
1. Follow steps in Chapter 3-2 to
UHPRYHWKHFDEOHFRYHUÀUVW
2. Pull the HDD tray from the system.
3. Attach the HDD to the HDD tray and
slide it into the slot until it snaps in
place. Please note the top of the
HDD should be on the upper side.
The system is equipped with a 90W power adapter. Please follow the steps to install
the power adapter.
1. The stand is designed to allow for clean cable management. There is a cable
channel through the stand, which has a quick access cover. Please pull the front
cover of the stand outwards.
2. Place the system face down. Making sure not to scrath the touchscreen.
3. Connect the power adapter to the 19V DC IN port and then route the cable as
shown in the picture.
4. Replace the front cover.
7

4. Peripheral Installation
4-1. Install the MSR Module
5HPRYHWKHGXPP\FRYHUÀUVW
2. Insert the MSR module in place and
fasten the screws (x2) on the back to
secure the module.
8

4-2. Install the Fingerprint Module
5HPRYHWKHGXPP\FRYHUÀUVW
2. Insert the Fingerprint module in
place and fasten the screws (x2) on
the back to secure the module.
9

4-3. Install the Customer Display
1. Follow the steps in Chapter 3-1 to diassemble the stand from the LCD panel.
2. Remove the thumb screw (x1) from the VESA top cover and then pull the cover
up.
3. Attach the LCM module to system by fastening the thumb screw (x1).
4. Route the cable through the hole of the stand as picture shown.
5. Attach the stand to the LCD panel and fasten the thumb screw (x1).
6. Connect the USB cable to a USB port on the systems IO panel.
* Please note the cable cover (refer to Chapter 3-2) have to be removed before
routing the cable.
10

4-4. Install the Second Display
1. Follow the steps in Chapter 3-1 to diassemble the stand from the LCD panel.
2. Remove the thumb screw (x1) from the VESA top cover and then pull the cover up.
3. Attach the 10.1"' 2nd display module to system by fastening the thumb screw (x1).
4. Attach the stand to the LCD panel and
fasten the thumb screw (x1).
5. Connect the 2nd display cable to VGA
port on the systems IO panel. Make
sure the system is powered off.
* Please note the cable cover (refer
to Chapter 3-2) have to be removed
before routing the cable.
11

4-5. Cash Drawer Installation
You can install a cash drawer through the cash drawer port. Please verify the pin
assignment before installation.
Cash Drawer Pin Assignment
Pin Signal
1 Cash drawer 2 In
2 Cash drawer 1 Out
3 Cash drawer 1 In
4 12V / 19V (or 24V)
5 Cash drawer 2 Out
6GND
1
6
Cash Drawer Controller Register
The Cash Drawer Controller use one I/O addresses to control the Cash Drawer.
Register Location: 0x482h
Attribute: Read / Write
Size: 8bit
BIT BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0
Attribute Reserved CD1 Out CD1 In Reserved
76543210
XXXXX X
Reserved
Cash Drawer 1 pin input control
Cash Drawer 1 pin output control
Reserved
12