POSIFLEX BB-3000 User manual

1
Package Contents
BB-3000 Bump Bar (x 1)
2m-Long Dedicated RS-232 Cable (x 1)
User Manual (x 1)
Views of the Bump Bar
Top View
Bottom View Front View
BB-3000
Bump Bar
User Manual
RS-232 Port
Reset Button
Status LED Indicator
Rubber Pad Rubber Pad
Fixed Portion
19100900010 Ver. Original
SERVE Button
NEXT Button
SIDE ON Button
RECALL Button
(Reserved)
SIDE OFF Button
SERVE Button
PREV Button
RECALL Button

2
Enabling the BB-3000
Power that enables the BB-3000 to work is supplied by your host terminal. To
make your host terminal supply power to the BB-3000, you need only a
dedicated RS-232 cable instead of a power adaptor. Thus, simply follow two
steps made below to power on the BB-3000.
1. Connect the RS-232 COM port of the BB-3000 to a specified COM port of
your host terminal through a dedicated RS-232 cable.
2. By using your dedicated application, select the specified COM port and a
baud rate.
3. Enable the COM port you selected.
Jumper Setting for a Baud Rate
To set a baud rate, please adjust the dip switch on the main board of the device.
Refer to the following steps to locate the dip switch on the main board.
1. Loosen and remove the two screws from the
top cover of BB-3000.
2. Remove the top cover.
3. You can easily find the dip switch on the
main board.

3
Functions of DIP Switch
DIP SWITCH
(Pin No.)
Functions
Pin 1
Pin 2
Baud rate settings
Pin 1/Pin 2 : OFF/OFF => 1200 bps
Pin 1/Pin 2 : OFF/ON => 2400 bps
Pin 1/Pin 2 : ON/OFF => 4800 bps
Pin 1/Pin 2 : ON/ON => 9600 bps (Default)
Pin 3
Pin 4
Pin 5
Pin 6
Code page change
Code page 1
Pin 3 : OFF / Pin 4 : OFF / Pin 5 : OFF / Pin 6 : OFF
SW1 : E2h / SW6 : E1h
SW2 : D2h / SW7 : D1h
SW3 : B2h / SW8 : B1h
SW4 : A2h / SW9 : A1h
SW5 : C2h / SW10 :C1h
Code page 2
Pin 3 : ON / Pin 4 : OFF / Pin 5 : ON / Pin 6 : OFF
SW1 : 62h / SW6 : 61h
SW2 : 52h / SW7 : 51h
SW3 : 32h / SW8 : 31h
SW4 : A2h / SW9 : A1h
SW5 : C2h / SW10 :C1h
Code page 3
Pin 3 : ON / Pin 4 : ON / Pin 5 : ON / Pin 6 : ON
SW1 : E2h / SW6 : E1h
SW2 : D2h / SW7 : D1h
SW3 : B2h / SW8 : B1h
SW4 : 22h / SW9 : 21h
SW5 : 42h / SW10 :41h
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
SW9
SW10

4
Regular Cleaning
For regular cleaning of the bump bar, please use only adequate amount of mild
kitchen cleaning detergent for obstinate stains and wipe it off with dry clean
soft clothes. Don’t allow any liquid to seep in through any seam in the metal
enclosure. It could also be a brilliant idea to seal the whole bump bar with thin
transparent wrap foil and replace the foil regularly.
Specifications
Buttons 10-key buttons
(8 buttons for SERVE/PREV/RECALL/SIDE
ON/SERVE/NEXT/RECALL/SIDE OFF; 2 buttons for reserved buttons)
I/O Port RS-232 COM port
DIP Switch 8-segment dip switch
Temp
& Humidity
Operation temp.: -25 to +70 ℃ / storage temp.: -30 to +80 ℃
Humidity: 10 to 90 %; 5 to 90 % (operation condition)
DIP SWITCH
(Pin No.)
Functions
Pin 7
Pin 8
Enabling or disabling DIP switch
Pin 7 : OFF / Pin 8 : OFF
Enabling SW1 ~ SW10
Pin 7 : OFF / Pin 8 : ON
Enabling SW1, SW2, SW5~SW7, and SW10
Pin 7 : ON / Pin 8 : OFF
Enabling SW3~SW5 and SW8~SW10