pottery barn kids CATALINA 3 IN 1 CRIB User manual


Date:21‐Jul‐14www.potterybarnkids.com  Page1of14
Rev:  





pottery barn kids


CATALINA 3 IN 1 CRIB































Date:21‐Jul‐14www.potterybarnkids.com  Page2of14
Rev:  


WARNING
Do not use this crib if you cannot exactly follow the accompanying instructions.
Do not use this crib for a child who can climb out of it or who is taller than 89 cm.
Do not place in or near this crib any cord, strap or similar item that could become
wrapped around a child’s neck.
Do not place this crib near a window or a patio door where a child could reach the cord of a
blind or curtain and be strangled.
Ensure that the crib is safe by checking regularly that every part is properly and securely in
place before placing the child in it. Do not use it if any parts are loose or missing or if there
are any signs of damage. Do not substitute parts. Contact the Pottery Barn Kids if
replacement parts or additional instructions are needed.
Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it is pushed
firmly against any side of the crib, it does not leave a gap of more than 3 cm between the
mattress and any part of the sides of the crib.
Children can suffocate on soft bedding. Do not place pillows, comforters or soft mattresses in
this crib.
04-000052-8
WARNING: Failure to follow these warnings and assembly instructions
could result in serious injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
Infants can suffocate in gaps between the crib sides and a mattress that is too small.
Never place additional padding under an infant.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
backs to sleep, unless otherwise advised by your physician.
STRANGULATION HAZARD: Strings can cause strangulation! Do not place items with a
string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings
over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
FALL HAZARD: When child is able to pull to a standing position, set mattress to lowest
position and remove bumper pads, large toys and other objects that could serve as steps for
climbing out.
Stop using crib when child begins to climb out or reaches the height of 35 in. (89cm)
Check this product for damaged hardware, loose joints, loose bolts or other fasteners,
missing parts or sharp edges before and after assembly and frequently during use. Securely
tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged
or broken. Contact Pottery Barn Kids for replacement parts and instructional literature if
needed. DO NOT substitute parts.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged, cracked, or loose. NOTE: This is only for cribs with teething
rails.


Date:21‐Jul‐14www.potterybarnkids.com  Page3of14
Rev:  


If refinishing, use a non-toxic finish specified for children’s products.
Do not remove the metal brackets from the mattress base after installation. NOTE: This is
only for cribs supplied with a wooden mattress base.
Follow warnings on all products in a crib.
04-000056-7
CAUTION: ANY MATTRESS USED
IN THIS CRIB MUST BE AT LEAST 27 ¼”
(69 CENTIMETERS) BY 51 5/8” (131
CENTIMETERS) WITH A THICKNESS NOT
EXCEEDING 6” (15 CENTIMETERS)
THIS CRIB CONFORMS TO APPLICABLE REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISSION.
04-000094-3
IMPORTANT SAFETY INSTRUCTIONS:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could
jeopardize the structural integrity of the item.
Do not remove warning labels from the cribs. Labels are permanent and not designed to be
removed
PRE-ASSEMBLY:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free
work surface, as this will avoid damaging parts during assembly. The shipping box provides
an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is
completed to avoid accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the
assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage
hardware and split wood.


Date:21‐Jul‐14www.potterybarnkids.com  Page4of14
Rev:  


Product labeling for Crib configuration with slatted crib ends. Crib is depicted upside down.
04‐000141
WarningLabel
04‐000141
WarningLabel
04-000141-1
Warning Label
Étiquette de Mise en Garde
04-000141-1
Warning Label
Étiquette de Mise en Garde


Date:21‐Jul‐14www.potterybarnkids.com  Page5of14
Rev:  


PARTS INCLUDED:
PART 1)- CRIB HEADBOARD (1x)
PART 2)- SPINDLE FOOT (2x)
PART 3)- LEFT CRIB END (1x)
PART 4)- RIGHT CRIB END (1x)
PART 5)- CRIB FRONT (1x)
PART 6)- MATTRESS BASE (1x)
3
4
1
6
5
2
2


Date:21‐Jul‐14www.potterybarnkids.com  Page6of14
Rev:  


HARDWARE INCLUDED:
A- Bolt- M6 x 70mm (8x)
B- Bolt- M6 x 20mm (4x)
C- Bolt- M6 x 60mm (2x)
D- HEADBOARD MEDALLION (2X)
E- M6 NUT (4X)
F- 4 MM BALL TIPALLEN KEY (1X)
(A)
1x
2x
2x
(B)
8x 4x
(F)
(C)
(D)(E)
4x


Date:21‐Jul‐14www.potterybarnkids.com  Page7of14
Rev:  


ASSEMBLY INSTRUCTION STEPS:
1. Attach the Spindle Foot (PART 2) to the Crib Headboard (PART 1) as shown.
1
2
2


Date:21‐Jul‐14www.potterybarnkids.com  Page8of14
Rev:  


2. Attach the Left Crib End (PART 3) and Right Crib End (PART 4) to the Crib Headboard
(PART 1) using Bolts (A) and the Allen Key (F).
1
(A) 3
4
(F)
(A) Bolt- M6 x 70mm 4x
Arrowstickersidedown.
Arrowpointsinside


Date:21‐Jul‐14www.potterybarnkids.com  Page9of14
Rev:  


3. Determine the desired height of the mattress base. Using two adults carefully place
mattress base into the crib taking care not to scratch the finish.
Note: The mattress base may be at the highest level when the child is born. It must be at the
lowest level before the child can stand up. Before installing the mattress base, please ask the
customer at which height they want it installed (Illustration showing Mattress base install in
the highest position).
Attach the Mattress Base (PART 6) to Crib Ends (PART 3 and 4) using the Bolts (B) and the
Allen Key (F). Do not fully tighten Bolts (B) at this point to make installation of the Crib Front
easier.
To change the position of the Mattress Base, unscrew Bolts (B), line up the Mattress Base with
the holes at the desired height and re-attach the Mattress Base using the same bolts.
(B) Bolt- M6 x 20mm 4x
Installed in the highest position.
6
(B)(F)
3
4
6


Date:21‐Jul‐14www.potterybarnkids.com  Page10of14
Rev:  


4. Attach the Crib Front (PART 5) to Crib Ends (PART 3 and 4) using Bolts (A) with Allen Key
(F).


(A) Bolt- M6 x 70mm 4x
Teethingrailsideup,arrowstickerside
down.Arrowpointsinside
(A)
(F)
5
3
4


Date:21‐Jul‐14www.potterybarnkids.com  Page11of14
Rev:  


5. Tighten all connections. Assembly is now complete. Place the assembly instructions back
into the envelope mounted on the mattress base for future reference.
CARE INSTRUCTIONS:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our
lacquered finish.
If the crib is to be stored, store in cool dry place and carefully package all original
hardware to protect from loss or damage.
Check fasteners periodically for tightness. Re-tighten if necessary. DO NOT over tighten.
This may cause distortion or breakage
Parents should ensure a safe environment for the child by checking regularly, before
placing the child in the product, that every component is properly and securely in place.


Date:21‐Jul‐14www.potterybarnkids.com  Page12of14
Rev:  


6. Taking care to attach the Headboard Medallion (D) to the headboard using bolt (C) with Allen
Key (F).
Make sure to align the medallion at a right angle square with the post before tightening.
(C) Bolt- M6 x 60mm 2x
(C)
1
(F)
(D)


Date:21‐Jul‐14www.potterybarnkids.com  Page13of14
Rev:  


7. ADJUSTING LEVELERS:
Due to an uneven floor the furniture may not sit level due causing it to wobbles. If the piece
wobbles, determine which corner does not touch the ground correctly. With the help of
another adult, follow these steps:
Carefully lift the item slightly to provide access to the levelers attached to the bottom.
Turn the levelers until adequate contact will be made with the floor. Gently set down the
piece and check stability.
Repeat steps until furniture sits firmly on the floor.


Date:21‐Jul‐14www.potterybarnkids.com  Page14of14
Rev:  


Thank you for your purchase
stores | catalog | www.potterybarnkids.com
U.S.A 1.800.290.8181
8. With the addition of a Box Spring Frame (sold separately), your Catalina Crib headboard can
be utilized as a full sized bed headboard. Follow the instruction below with 2 adults:
1) Disassemble your Crib or Toddler Bed and set all pieces and hardware aside in an
organized manner.
2) Assemble the Box spring Frame according to the instructions included with the frame.
3) Hold the Catalina Headboard (Part 1) upright near the desired location in the room.
4) Insert the 4 Bolts (A) that you removed from the Crib into the pre-drilled holes in the
bottom back side of both legs
5) Attach and align the Box Spring Frame onto the Headboard Leg Bolts.
6) Tighten the 4 Nuts (E) over the end of the Bolt ends using the Allen Key and a wrench (not
included).
7) Package and store for future use the remaining unused parts and original hardware to
protect from loss or damage.
(A) Bolt- M6 x 70mm 4x(E) M6 NUT 4x
1
(F)
(A)
(E)
(E)
(A)