pottery barn kids STAR WARS BED User manual

Date: 2054-Jun.-18
Rev: Page 1 of 14
pottery barn kids
STAR WARS BED (Part 2 of 2)
Please follow strickly this assembling instruction to prevent this bed
from damage or misalignment.
www.potterybarnkids.com

Date: 2015-Jun.-18
Rev: Page 2 of 14
WARNING:. Follow mattress manufacturer instructions for use.
Use proper ventilation foundation with latex mattresses. Failure to follow
this instruction can lead to property damage.
Important Safety Instructions:
•Please read all instructions carefully before assembling.
•For your safety, assembly by four or more adults is strongly recommended.
•Keep these instructions for future use.
•Use only vendor-supplied hardware to assemble this item. Using unauthorized hardware could jeopardize the
structural integrity of the item.
Pre-assembly:
•Remove all parts and hardware from the box. Place all items on a carpeted or scratch-free work surface, as this
will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
•To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or contents of the
shipping carton until assembly is complete.
•Use the parts and hardware lists below to identify and separate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
•The use of power tools to aid in assembly is not recommended. Power tools can damage the hardware and split
the wood.
•Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the
bolts to misalign during assembly.
Parts Included:

Date: 2015-Jun.-18
Rev: Page 3 of 14
(A) Footboard (x1) (B) Headboard (x1)
(CL) Left triangle block(x2) (CR) Right triangle block(x2)
(DL) 1st Left side rail(x1) (DR) 1st Right side rail(x1)
(EL) 2nd Left side rail(x1) (ER) 2nd Right side rail(x1)
(F) 3rd Side rail(x2) (G) Bottom Panel(x1)
(H) Leg(x4)(I) Platform panel(x3)
(J) Center leg(X3)
Hardware Included:
Tools Required:
Phillips head screwdriver (not included)
(K)Allen Key
with ball
tip – 1x
(L)Allen Bolt
1/4”x57mm - 26x
(M)Spring Washer
1/4”x10x1.5mm - 26x
(N)Flat Washer
1/4”x12x1.5mm - 26x
(O) Half Moon Washer
1/4x24x8mm–18x
(S)AllenKey
6x75x30mm -1x
(T) Cam
15x25mm - 8x
(U)Cam Bolt
M6x8.5x56mm -8x
(V) Mending Plate
- 6x
(W) Philip Head Screw
8x19mm - 24x
(X) Philip Head Screw
8x30mm - 12x

Date: 2015-Jun.-18
Rev: Page 4 of 14
ASSEMBLY INSTRUCTIONS
1. Make sure the Footboard (A) is fully assembled followed separated AI. Lay down (A) on a Styrofoam taken from
the carton as seen in the illustration below. Using Platform Panel (I) as an measurement to make sure the
Footboard is placed straightly as shown below.
2. Attach (G) to (A), with the wooden dowels and pre-drilled holes aligned, as seen in the illustration below.
*Tip: See Image A for ease of assembly.
L 1x
M 1x
N 1x
O 1x
Image A
NO T OK
Styrofoam

Date: 2015-Jun.-18
Rev: Page 5 of 14
3. Attach 4pcs (H) to 02pcs (F), with the pre-drilled holes aligned, as seen in the illustration below.
4. Attach (F) to (A), with the wooden dowels and pre-drilled holes aligned, as seen in the illustration below.
Adjust the levelers on the bottom of the unit (up or down) to level the panel.
L 8x
M 8x
N 8x
4x

Date: 2015-Jun.-18
Rev: Page 6 of 14
5. Tighten with bolt (attach to (A)) and mending plate (attach to (F)), as seen in the illustration below.
*Tip: See Image A (Page 4) for ease of assembly.
6. Repeat step #4 to assemble another side Rail (F), as seen in the illustration below.
L 1x
M 1x
N 1x
O 1x
V 1x
W 4x

Date: 2015-Jun.-18
Rev: Page 7 of 14
7. Repeat step # 5 to assemble another side Rail (F) to (A) & (G), as seen in the illustration below.
*Tip: See Image A (Page 4) for ease of assembly.
8. Attach (EL& ER) to (A), as seen in the illustration below.
*Tip: See Image A (Page 4) for ease of assembly.
L 1x
M 1x
N 1x
O 1x
V 1x
W 4x
L 4x
M 4x
N 4x
O 4x

Date: 2015-Jun.-18
Rev: Page 8 of 14
9. Attach (EL) and (ER) to (F), as seen in the illustration below.
Note: Tighten the mending plate to the pre-drilled holes first. Check aligment and tighten the rest screws.
10. Thread (U) to (DL&DR), as seen in the illustration below.
V 2x
W 8x
U 4x

Date: 2015-Jun.-18
Rev: Page 9 of 14
Note:
- Prior to inserting the Cam into the countersunk, align the outer arrow on the Cam with the inner arrow at
the center of the Cam, as seen below.
- The cam may become disassembled during shipping. If you find it disassembled, please re-assemble,
as shown in the illustration below.
11. Insert (T) to (CL&CR), attach (CL&CR) to (DL&DR), tighten (T) with Allen key (S) as seen in the illustration
below.
T 4x
S 1x

Date: 2015-Jun.-18
Rev: Page 10 of 14
12. Insert (U) to (A), as seen in the illustration below.
13. Insert (T) to (CL&CR), attach(DL&DR) to (A), tighten (T) with Allen key (S) as seen in the illustration below.
.
U 2x
T 2x

Date: 2015-Jun.-18
Rev: Page 11 of 14
14. Repeat step # 5 to secure (DL&DR ) to (A) and (EL & ER), as seen in the illustration below.
15. Insert (U) to (B) , as seen in the illustration below.
L 2x
M 2x
N 2x
O 2x
V 2x
W 8x
U 2x

Date: 2015-Jun.-18
Rev: Page 12 of 14
16. Insert (T) to (CL&CR), attach(B) to (CL&CR), tighten (T) with Allen key (S) as seen in the illustration below.
17. Secure all side rails to Headboard (B), as seen in the illustration below.
*Tip: See Image A (Page 4) for ease of assembly.
T 2x
L 9x
M 9x
N 9x
O 9x

Date: 2015-Jun.-18
Rev: Page 13 of 14
18. Thread 03pcs (J) to 03pcs (I), as seen in the illustration below.
19. Place (I) in between of slat support on side rails, adjust the levelers on the bottom of the support legs (J) up
or down) to level the panel, as seen in the illustration below.

Date: 2015-Jun.-18
Rev: Page 14 of 14
20. Secure (I) with screw (X).
21. Remove the Styrofoam under the footboard, as seen in the illustration below.
22. Assembly is now complete.
Care Instructions:
•Dust often using a clean, soft, dry, and lint-free cloth.
•Blot spills immediately and wipe with a clean, damp cloth.
•We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
•Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thank you for your purchase
Stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181
X 12x