Power Fist 8474983 User manual

V0.1 8474983
Please read and understand all instructions before use. Retain this manual for
future reference.

8474983 20 Gallon Portable Air Compressor V0.1
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Air Delivery 3.5 CFM @ 90 PSI
4.8 CFM @ 40 PSI
Air Tank Capacity 20 Gallons (76 litres)
Max. Air Pressure 125 PSI
Cut-In Pressure 95 PSI
Cut-Out Pressure 125 PSI
Compressor Type Direct Drive, Single Stage
Pump Style Oil Free
Current Rating 15A
Voltage Rating 120V, 60Hz
Duty Cycle 50%
Noise Rating 82 dB
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or
death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not
taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice
will result in equipment or property damage, but not personal
injury.

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 3
INTRODUCTION
The 20 Gallon Portable Air Compressor is ideal for light duty pneumatic tool
applications and general household use. The compressor is low maintenance
with a direct drive motor and oil free pump. The 20 gallon ASME vertical
portable tank comes with a cushioned handle grip. Fully enclosed plastic
shroud covers working components. The compressor plugs into a standard
120 volt outlet for quick and easy use.
The compressor is equipped with pressure regulator, pressure gauges, quick
connect air outlet and ON/OFF switch.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection
and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well lit
and free of distractions.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store the device properly in a safe and dry location. Keep out of the
reach of children.
4. Do not install or use in the presence of flammable gases or liquids. Always
operate compressor in a well ventilated area. Locate the compressor at
least 20 feet away from work area if spraying flammable materials.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Wear personal protection equipment such as ANSI Z87.1 approved safety
goggles, respirator, gloves, steel toe footwear or a hard hat as
warranted by the work environment.
a. This device can cause hearing damage. Wear hearing protection
with an appropriate Noise Reduction Rating, especially if using it
for extended periods.

8474983 20 Gallon Portable Air Compressor V0.1
4 For technical questions call 1-800-665-8685
2. Control the device, personal movement and the work environment to
avoid personal injury or damage to the device.
3. Do not operate any device when tired or under the influence of drugs,
alcohol or medications.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific function.
Do not modify or alter this tool or use it for an unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced. Repair
or replace the parts.
3. Risk of Bursting
a. Serious injury or death may occur from an air tank explosion if the air
tank is not properly maintained or if modifications, alterations or
repairs are attempted. Drain air tank daily or after each use. Never
drill into, weld, patch or modify the air tank. Replace the tank
immediately or replace the entire compressor, if a leak develops.
b. Serious injury or death may occur if modifications are made to the
pressure switch, safety relief valve or other components that
control the tank pressure. Never make adjustments to the
components that control tank pressure. Do not make alterations to
the factory operating pressure settings. Check operation of the
pressure relief valve on a regular basis and never operate without a
factory approved pressure relief valve.
c. Check the manufacturer’s maximum pressure rating for air tools
and accessories. Compressor outlet pressure must be regulated so
as to never exceed the maximum pressure rating of the tool.

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 5
4. Risk of Explosion or Fire
Serious injury may occur if a fire is caused by overheating due to
inadequate ventilation or restrictions to any of the compressor’s ventilation
openings. Never place objects against or on top of an air compressor.
Always operate air compressor at least 12 in. away from any wall or
obstruction. Always operate in a clean, dry and well-ventilated area.
5. Risk of Burn
Serious burn injuries could occur from touching exposed metal parts such
as the compressor head or motor during operation and even after the
compressor is shut down for some time. Never touch any of the exposed
metal parts during operation and for an extended period of time after the
air compressor has shut down. Do not attempt maintenance on the unit
until it has been allowed to completely cool.
6. Risk from Moving Parts
a. Serious injury may occur if repairs are attempted with damaged,
missing or removed protective guards, shrouds or missing covers.
All repairs to the air compressor should be made only by authorized
or trained service personnel.
b. This unit starts automatically. Always shut off the compressor and
bleed all pressure from the system before servicing the compressor
and when the compressor is not in use.
7. Flying Objects
a. Serious injury may occur from loose debris being propelled at high
speeds from the compressed air stream. Always wear OSHA
approved safety glasses to protect the eyes during operation of the
air compressor.
b. Never point the air stream or tools at any point of your body, other
people or animals. Debris and dust may be ejected without warning.
Always turn off the air compressor and drain tank pressure
completely before attempting maintenance or attaching air tools.
Release pressure slowly from the system.
8. Risk of Damage to Air Compressor or Property
a. Failure to transport or operate the air compressor properly may result
in major repair expenses. Always run the compressor in a level, secure
position that keeps it from tipping or falling during use.
b. Do not operate without an air filter or in a corrosive environment.

8474983 20 Gallon Portable Air Compressor V0.1
6 For technical questions call 1-800-665-8685
c. Always transport in a level position and use protective mats to keep
truck beds clean, etc. Fasten the compressor down securely. Pressure
must be released from the tank before transporting.
d. In cold climates, drain the tank after each use to avoid ice build up.
GENERAL SAFETY PRECAUTIONS
ELECTRICAL SAFETY
WARNING! To reduce risk of electric shock, be certain that the plug is
connected to a properly grounded receptacle.
1. Disconnect device from power source before cleaning, servicing,
changing parts/accessories or when not in use.
2. Protect yourself against electric shocks when working on electrical
equipment. Avoid body contact with grounded surfaces. There is an
increased chance of electrical shock if your body is grounded.
3. Do not disconnect the power cord in place of using the AUTO/OFF
switch on the device. This will prevent an accidental start up when the
power cord is plugged into the power supply.
4. Do not alter any parts of the device or accessories. All parts and
accessories are designed with built-in safety features that may be
compromised if altered.
5. Make certain the power source conforms to requirements of your
equipment.
6. To reduce the risk of electric shock, do not expose to rain or use on a
wet surface. Store the compressor indoors.
7. Use time delay fuses with this product when the circuit is connected to
a fuse box.
8. When wiring an electrically driven device, follow all electrical and
safety codes, as well as the most recent Canadian Electrical Code (CE)
and Canadian Centre for Occupational Health and Safety (CCOHS).
9. DO NOT use this device with a 2-prong wall receptacle.
a. Choose an available 3-prong power outlet.
b. Replace 2 prong outlet with a grounded 3-prong receptacle,
installed in accordance with the CE Code and local codes and
ordinances.

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 7
POWER CORD
1. Insert the power cord plug directly to the power supply whenever
possible. Use extension cords or surge protectors only when the
device's power cord cannot reach a power supply from the work area
(see below).
a. If an extension cord must be used, ensure it is at most 50 ft long
and at least 12 gauge wire thickness.
2. Do not operate this device if the power cord is frayed or damaged as an
electric shock may occur, resulting in personal injury or property
damage.
a. Inspect the device's power cord for cracks, fraying or other faults in
the insulation or plug before each use.
b. Discontinue use if a power cord feels more than comfortably warm
while operating the device.
c. Have the power cord replaced by a qualified service technician
3. Keep all connections dry and off the ground to reduce the risk of
electric shock. Do not touch plug with wet hands.
4. Prevent damage to the power cord by observing the following:
a. Do not pull on the cord to disconnect the plug from an outlet.
b. Keep cord away from heat, oil, sharp edges or moving parts.
5. Do not allow people, mobile equipment or vehicles to pass over
unprotected power cords.
a. Position power cords away from traffic areas.
b. Place cords in reinforced conduits.
c. Place planks on either side of the power cord to create a protective
trench.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the contents are included.

8474983 20 Gallon Portable Air Compressor V0.1
8 For technical questions call 1-800-665-8685
Contents:
• Air compressor
• 25 ft PE coil hose
• Blow gun with safety nozzle
• Inflation needle and adapter fitting
• Dual head tire chuck
• 1/4 in. female Quick coupler
• 1/4 in. NPT male and female QC
plugs
• Thread sealant
BASIC AIR COMPRESSOR COMPONENTS
Oil free air compressors are factory lubricated for life and do not require any oil.
The basic components of the air compressor are the electric motor, pump,
pressure switch and tank.
The electric motor (A) powers the pump. The electric
motor is equipped with an overload protector and an
automatic reset. If the motor becomes overheated,
the overload protector will shut it down to prevent
damage to the motor. When the motor sufficiently
cools, it will automatically reset.
The pump (A) compresses the air and discharges it
into the tank.
The tank (B) stores the compressed air.
The pressure switch (C) shuts down the motor when the
air pressure in the tank reaches the cut-out pressure. As
compressed air is used and the pressure level in the tank
drops to the cut-in pressure, the pressure switch restarts
the motor automatically, without warning and the pump
resumes compressing air.
COMPRESSOR CONTROLS
A. AUTO/OFF SWITCH
This switch turns on the compressor. It is operated manually, but when in
the AUTO position, it allows the compressor to start up or shut down
automatically, without warning, upon air demand. ALWAYS set this switch to
OFF when the compressor is not being used, and before unplugging the
compressor.
B. PRESSURE RELIEF VALVE
The air compressor is equipped with a pressure relief valve that is designed to
discharge tank pressure at a predetermined setting when a systems failure
occurs. Check the pressure valve periodically by pulling on the ring only when
Fig. 1

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 9
the tank pressure is completely drained. The spring
loaded valve should move freely within the
pressure valve body. An inoperable pressure valve
could allow an excessive amount of tank pressure
to build causing the air tank to catastrophically
rupture or explode.
Do not tamper with or attempt to eliminate the
pressure relief valve.
C. TANK PRESSURE GAUGE
This gauge measures the pressure level of the air
stored in the tank. It is not adjustable by the
operator, and does not indicate line pressure.
D. AIR PRESSURE REGULATOR
This air pressure regulator enables you to adjust line pressure to the tool
you are using. Turn the knob clockwise to increase pressure, and
counterclockwise to decrease pressure.
E. REGULATED PRESSURE GAUGE
This gauge measures the regulated outlet pressure.
F. AIR LINE OUTLET
Connect an air hose to this outlet.
ASSEMBLY & INSTALLATION
Letter references in parenthesis (A) refer to the
included Identification Key.
1. Remove the compressor from the carton and
place it on the floor or a hard, level surface.
The compressor must be level to ensure
proper drainage of the moisture in the tank.
2. The wheels are disassembled. Remove 2
wheels (D), 2 bolts (E), washers (F) and 2 nuts
(G) from the bag and install them on the foot
section of the tank as shown in (see Fig. 4).
3. Install the handle by placing the handle ends
(B) onto the base and secure with the bolts
(C) provided (see Fig. 4). Tighten bolts using a
13 mm socket or wrench (not included).
Fig. 2
Fig. 3

8474983 20 Gallon Portable Air Compressor V0.1
10 For technical questions call 1-800-665-8685
OPERATION
PRE-START CHECKLIST
1. Always operate the compressor in a level position to allow the tank to drain.
2. Inspect/clean/change intake elements on a regular basis. The ingestion
of dirt into the pump is the primary cause of premature wear. Check
intake filters daily.
3. Check tension of bolts and hardware on a regular basis. Operation of
any equipment with loose bolts and/or fittings will lead to excessive
vibration and the premature failure of the compressor system control
components.
4. Drain moisture from the air tank daily. Water is a natural by-product of
compressed air. Drain the air tank after each use to combat internal
tank corrosion. Keep drain valves open if storing compressor for any
length of time.
DAILY START UP
WARNING! High temperatures are generated by the electric motor and the
pump. To prevent burns or other injuries, DO NOT touch the compressor
while it is running. Allow it to cool before handling or servicing. Keep
children away from the compressor at all times.
WARNING! When adjusting from a higher to a lower pressure, turn the knob
anticlockwise past the desired setting, then turn clockwise to reach the desired
pressure. Do not exceed operating pressure of the tool or accessory being used.
1. Turn the pressure switch to the OFF position (A). (Fig. 2)
2. Close the tank drain valve (D). (Fig. 4)
3. Plug in the power cord.
4. Turn the pressure switch to the AUTO position (A). (Fig. 2)
5. Adjust the air pressure regulator to the working pressure of the tool
being used.
SHUTDOWN
1. Turn the pressure switch to the OFF position (A).
2. Unplug the power cord.
3. Reduce pressure in the tank by slowly opening the drain valve at the
bottom of the tank (B). The escaping air will also blow condensation out.
Leave the drain valve open until the next use.

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 11
CARE & MAINTENANCE
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
CAUTION! Always unplug or shut down your compressor and drain the air
tank completely before attempting any type of maintenance. Wait for
compressor to cool before servicing.
1. Maintain the device with care. A device in
good condition is efficient, easier to control
and will have fewer problems.
2. Inspect the device components
periodically. Repair or replace damaged or
worn components.
3. Follow instructions for lubricating and
changing accessories.
4. Drain tank of moisture after each day’s use.
If unit will not be used for a while, it is best
to leave drain valve open until such time as
it is to be used. This will allow moisture to
completely drain out and help prevent
corrosion on the inside of tank (Fig. 4).
5. Inspect the device fittings, alignment and
hoses periodically. Have damaged or worn
components repaired or replaced by an authorized technician.
a. Pull the pressure relief valve daily to ensure that it is operating
properly and to clear the valve of any possible obstructions.
b. Check that all connections are tight and don’t leak.
6. Maintain the device’s label and nameplate. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
Fig. 4

8474983 20 Gallon Portable Air Compressor V0.1
12 For technical questions call 1-800-665-8685
MAINTENANCE SCHEDULE
Recommendation Daily Weekly Monthly Quarterly Annually
Drain Moisture from Tank(s) X
Inspect Filter(s) X
Check for Unusual Noise or
Vibration
X
Check for Air Leaks X
Clean Exterior of Air Compressor X
Tighten/Retorque Bolts X
Check Operation of Pressure Relief
Valve
X
Clean/Change Filter X
Perform Pump Up Time Test X
Check Operation of System Controls X
Check Air Tank(s) for Dents/Leaks X
Inspect Tank for Rust, Pinholes, or
other Imperfections.
X
LUBRICATION
The oil free air compressor is factory lubricated for life and does not require
any oil for the pump.
STORAGE
Before storing the compressor for a prolonged period, use an air blowgun to
clean all dust and debris from the compressor. Disconnect the power cord
and coil it up on the handle. Open the drain valve to release all pressure
from the tank. This will also drain all moisture from the tank. Clean the filter
element and filter housing; replace the element if necessary. Drain the oil
from the pump crankcase and replace it with new oil. Cover the entire unit
to protect it from moisture and dust.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 13
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
Problem(s) Possible Cause(s) Suggested Solution(s)
Low pressure or
not enough air or
compressor does
not stop.
1. Tank drain valve is
open.
2. Fittings leak.
3. Restricted air intake.
4. Prolonged excessive
use of air.
5. Compressor not large
enough.
6. Hole in air hose.
7. Tank leaks.
8. Blown seals.
9. Valve leaks.
10. Leaking or worn
piston.
1. Close drain valve.
2.
Check fittings with soapy water.
Tighten or reseal leaking
fittings. DO NOT OVERTIGHTEN.
3. Clean or replace intake filter
element.
4. Decrease amount of air used.
5. Check air requirement of
accessory. If it is higher than
CFM and pressure supplied by
compressor, you need a larger
compressor. Most accessories
are rated at 25% of actual CFM
while running continuously.
6. Check and replace if necessary.
7. Immediately replace tank. DO
NOT attempt to repair.
8. Replace seals.
9. Replace valve.
10. Replace piston.
Air leaks from
regulator or
regulator does not
regulate pressure.
Dirty or damaged
regulator internal parts.
Dirty or damaged regulator internal
parts.
Regulated pressure
gauge reading drops
when air accessory
is being used.
1. This is normal.
2. Compressor not large
enough.
1. If pressure drops too low, adjust
regulator while accessory is
used.
2. Check air requirement of
accessory. If it is higher than
CFM and pressure supplied by
compressor, you need a larger
compressor. Most accessories
are rated at 25% of actual CFM
while running continuously.

8474983 20 Gallon Portable Air Compressor V0.1
14 For technical questions call 1-800-665-8685
Pressure relief valve
opens.
1. Tank pressure
exceeded normal
operating pressure.
2. Pressure switch
stuck.
1. Replace pressure switch.
2. Replace pressure switch.
Motor will not run. 1. Tank pressure
exceeds preset
pressure switch limit.
2. Fuse blown or circuit
breaker tripped
(make sure the
thermal overload
switch has not
tripped. The motor
has a built-in thermal
cut-out that trips to
protect the motor
from damage due to
overheating).
3. Check valve stuck
open.
4. Extension cord is too
long, too light gauge
or damaged.
5. Loose electrical
connections.
6. Paint spray on
internal motor parts.
7. Possible defective
motor.
1. Motor will start automatically
when tank pressure drops
below the cut-in pressure of
pressure tank.
2. Replace blown fuse or reset
circuit breaker. Do not use fuse
or circuit breaker with higher
rating than specified for your
branch circuit. To reset the
motor overload, turn the
pressure switch AUTO/OFF lever
to the OFF position and unplug
the unit from the power outlet.
Allow 10 minutes minimum for
motor overload cut-out to cool
and reset. Unit can then be
plugged in and re-started.
2a. Check for proper fuse. A
fuse type T, such as a
Fusetron, is acceptable.
2b. Check for low voltage and
proper extension cord size.
2c. Disconnect other
applications from circuit.
Operate compressor on a
dedicated circuit.
3. Remove and clean or replace.
4. Replace extension cord with
another one that is at most 50
ft long and at least 12 gauge.
5. Contact Princess Auto Ltd. for a
solution.
6. Do not operate compressor in
the paint spray area. Contact
Princess Auto Ltd. for a solution.
7. Contact Princess Auto Ltd. for a
solution.

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 15
PARTS BREAKDOWN
PARTS LIST - MOTOR
# DESCRIPTION QTY KIT PART ID
1 Screw, SHC M6 X 1.0 X 35 mm 4 7
2
Washer, Lock M6
6
4 & 7
3 Head, Cylinder 1 7 E100284
4
Screw, HFH M3 X 0.4 X 5 mm
2
1 & 7
5 Washer, Lock M3 1 1 & 7
6
Retainer, Outlet Valve
1
1 & 7
7 Valve, Outlet 1 1 & 7
8
Gasket, O-ring, Head
1
1, 7 & 10

8474983 20 Gallon Portable Air Compressor V0.1
16 For technical questions call 1-800-665-8685
9
Valve Plate
1
1 & 7
10
Gasket, O-ring, Cylinder
1
1, 7 & 10
11
Valve, Inlet
1
1 & 7
12
Retainer, Inlet Valve
1
1 & 7
13
Cylinder
1
2 & 7
14
Screw, Pan Head M6 x 1.0 x 10 mm
4
7
15
Shroud, Motor End Cap
1
7
E104779
16
Motor/Pump F2
1
7
17
Assy, Eccentric & Bearing 6203ZC3
1
3 & 7
18
Screw, SHCS M6 X 1 X 35 mm
1
3 & 7
19
Nut, M5 X 0.8
1
2 & 7
20
Screw, SHCS M5 X 0.8 X 25 mm
1
2 & 7
21
Rod, Connector
1
2 & 7
22
Ring, Piston
1
2 & 7
23
Cap, Piston
1
2 & 7
24
Screw, SHC M5 X 0.8 X 15 mm
1
2 & 7
25
Fan, Cooling
1
4
26
Washer, Flat M6
1
4
27
Screw, SHC M6 x 1.0 x 16 mm (Left Hand Thread)
1
4
28
Capacitor, Running (Motor-50μF/250VAC) Bkt Mt
1
7
E104273
29
Capacitor, Starting (Motor-250μF/125VAC) Bkt
Mt.
1
7
E104272
30
Nut, M8 x 1.25
2
7
31
---

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 17
PARTS LIST - COMPRESSOR
# DESCRIPTION QTY KIT PART ID
32 Shroud, Full Rear 1 E100300
33
Grip, Slide On, 20 mm
1
E101490
34 Handle 1 E103967
35
---

8474983 20 Gallon Portable Air Compressor V0.1
18 For technical questions call 1-800-665-8685
36
Gauge, Pressure 1.5 in. (Blk Hsn/White Face)
2
E103339
37
---
38
Coupling, Quick Connect
1
E100307
39
Cord, Power, 14/3 AWG, Length 6 ft Type ST
1
E101073
40
Restraint, Power Cord - 14/3 ST
1
E101800
41
Regulator, 3-Port, Left Flow 1/4 in. NPT
1
E100971
42
Nipple, 1/4 in. MNPT x 35 mm
2
E100853
43
Switch, Pressure Assy 125 PSIG 4 X 1/4 in. NPT Base
1
E104555
44
Valve, Safety
1
E102595
45
Weldment, Assembly Tank, 20 Gallon Vertical
1
46
Nut, Hex Lock Nylon Inserted M10 x 1.5 (Bright Zinc)
2
5
47
Washer, Flat M10
2
5
48
Wheel, 7 x 1.5 in. Diamond Tread
2
5
49
Bolt, Shoulder M10 x 1.5 x 55 (Shoulder To 39 mm)
2
5
50
Valve, Drain, 1/4 Turn
1
E101717
51
Screw, HH M8 X 1.25 Self Tap
2
52
Washer, Flat M8 X 22 mm
2
53
Isolator, Foot (60 mm Dia. x 28 mm Tall)
2
E100240
54
Washer, Flat M6 X 12 mm OD
2
55
Screw, HH M6 X 1.0 X 20 mm
2
56
Ferrule, 3/8 in.
1
6
57
Nut, Comp, 3/8 in.
1
6
58
Assy, 3/8 in. Finned Outlet Tube
1
6
59
Shroud, F2, Full, Front
1
E100296
60
Screw, HFH M6 x1.0 x 12 mm
6
61
Elbow, Exhaust 90 deg. 13 mm Male Flr X 1/2 in. MNPT
1
E100283
62
Motor/Pump Assembly F2B2 (Right Hand Exhaust)
7
63
Screw, SHC M8 x 1.25 x 16 mm (ZDC Plate)
4
64
Washer, Lock 8 mm
8
65
Washer, Flat 8 mm X 19 mm
8
66
Nut, M8 x 1.25
4
67
Valve, Check, 90 Degree Left
1
E101362
68
Tube, Relief, 1/4 in. Copper Formed (F2 On 400 mm Vert)
1
8
69
Nut, Comp, 1/4 in.
2
8
70
Ferrule, Comp 1/4 in.
2
8
71
Screw, HH M8 X 1.25 X 25 mm
4

V0.1 20 Gallon Portable Air Compressor 8474983
Visit www.princessauto.com for more information 19
72
Base, Air Filter
1
9
73
Element, Air Filter
1
9
E100435
74
Cap, Air Filter
1
9
PARTS LIST - KIT
KIT # KIT NAME PART # ORDER #
1 Kit, Valve Plate 4-12 E103497
2 Kit, Piston 13, 19-24 E103495
3 Kit, Eccentric 17-18 E104441
4 Kit, F2 Pump Fan 2, 25-27 E104280
5 Kit, Wheel (Replaces One Wheel Assy.) 46-49 E104442
6 Kit, Finned Aluminum 3/8 in. Outlet Tube 56-58 E103286
7 Kit, F2B2 Motor/Pump Assy (Right Hand Exhaust) 1 - 30, 62 E104279
8 Kit, Pressure Relief Tube 1/4 in. Copper 68-70 E104834
9 Kit, Air Filter 72-74 E100794
10 Kit, O-ring 8, 10 E105845

8474983 20 Gallon Portable Air Compressor V0.1
20 For technical questions call 1-800-665-8685