Power Fist 10 in. Bench-Top Drill Press User manual

V 4.0 8654337
User Manual
10in.Bench-Top
DrillPress
Please read and understand all instructions before use. Retain this manual for
future reference.

8654337 10 in. Bench-Top Drill Press V 4.0
SPECIFICATIONS
Number of Speeds 12
Speed(s) RPM 300, 370, 470, 570, 630, 690, 950, 1,400, 1,620, 1,760,
2,550 and 2,900
Chuck Size 5/8 in.
Spindle Travel 2-3/8 in.
Spindle Taper B16
Swing 10 in.
Table Tilt 45º Left/Right
Voltage Rating 120V a.c.
Current Rating 3.85A
Frequency Rating 60Hz
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection and
maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice
is an alert that there is a possibility of property damage, injury or death if certain
instructions are not followed.
10in.Bench-Top
DrillPress
2 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions
are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may result
in minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice will
result in equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions.
2. Keep anyone not wearing the appropriate safety equipment away from the
work area.
3. Store unused tools properly in a safe and dry location to prevent rust or
damage. Lock tools away and keep out of the reach of children.
4. Do not install or use in the presence of flammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. Wear the appropriate type of full-face shield in addition to safety googles,
as the work can create chips, abrasive or particulate matter.
3. Wear gloves that provide protection based on the work materials or to
reduce the effects of tool vibration.
a. Do not wear gloves when operating a tool that can snag the material
and pull the hand into the tool.
Visit www.princessauto.com for more information 3

8654337 10 in. Bench-Top Drill Press V 4.0
4. Wear protective clothing designed for the work environment and tool.
5. Non-skid footwear is recommended to maintain footing and balance in the
work environment.
6. Wear steel toe footwear or steel toe caps to prevent a foot injury from
falling objects.
7. Wear the appropriate rated dust mask or respirator.
8. This tool can cause hearing damage. Wear hearing protection gear with an
appropriate Noise Reduction Rating to withstand the decibel levels.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs, alcohol
or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
4. Support the workpiece or clamp it to a stable platform. Holding the
workpiece by hand or against your body may lead to personal injury.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a
specific function. Do not modify or alter this tool or use it for
an unintended purpose.
2. Use recommended speed for drill accessory and workpiece material.
3. The chuck key is designed to self-eject if the drill press is started before it
is removed.
4 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to vibration
may cause temporary or permanent physical injury. Take frequent breaks
when using the tool.
2. If you feel any medical symptoms related to vibrations (such as tingling,
numbness and white or blue fingers), seek medical attention as soon
as possible.
3. Wear suitable gloves to reduce the effects of vibration.
4. DO NOT use this tool before consulting a physician if one of the
following applies:
a. Pregnant
b. Impaired blood circulation
to the hands
c. Past hand injuries
d. Nervous system disorders
e. Diabetes
f. Raynaud's Disease
POWER TOOL PRECAUTIONS
1. Do not allow the tool to run without load for an extended period of time, as
this will shorten its life.
2. Do not cover the air vents. Proper cooling of the motor is necessary to
ensure normal life of the tool.
3. Avoid unintentional starting. Ensure the switch is off when connecting to
the power source.
4. Disconnect the power source before installing or servicing the tool.
5. After making adjustments, make sure that any adjustment devices are
securely tightened.
6. Remove adjusting keys and wrenches before turning the tool on. A wrench
or a key that is left attached to a rotating part of the tool increases the risk
of personal injury.
7. Never force the tool. Excessive pressure could break the tool, resulting in
damage to your workpiece or serious personal injury. If your tool runs
smoothly under no load, but does not run smoothly under load, then
excessive pressure is being used.
Visit www.princessauto.com for more information 5

8654337 10 in. Bench-Top Drill Press V 4.0
8. Do not touch an operating motor. Motors can operate at high temperatures
and can cause a burn injury.
9. Only use accessories that are specifically designed for use with the tool.
Ensure the accessory is tightly installed.
CUTTING TOOL PRECAUTIONS
WARNING! Some surfaces contain materials which can be toxic. When
working on materials that may contain lead, asbestos, copper chromium
arsenate or other toxic materials, extra care should be taken to avoid
inhalation and minimize skin contact.
The term cutting accessory is used to represent a cutting blade, cutting wheel
or a cutting bit.
1. Keep hands away from the cutting area and the cutting accessory.
2. Only use a cutting accessory of the recommended size (see
Specifications).
3. Check the cutting accessory for damage before each use. A damaged
accessory can break during use and cause serious injury.
4. Inspect material for foreign objects such as staples, nails or debris.
Remove from material before cutting.
5. Do not touch the cutting accessory or the workpiece surface cut with this
tool. They may be hot and could inflict a burn injury.
DRILLING PRECAUTIONS
The term bit refers to any drill bits, router bits or tool accessories that penetrate
a material and creates a cavity through a rotary motion.
1. Never force the tool’s bit. Forcing the tool will slow down the cutting speed of the
bit, causing it to bind. Apply gentle pressure and allow the bit to do the cutting.
2. Do not use a bit with a dull or damaged cutting edge. Keep the cutting edge
sharp and clean. A dull bit may cause the tool to skitter across the work
surface instead of penetrating the material. This may cause an injury and
will damage the workpiece.
3. Hardened gum and wood pitch on a bit slows the tool down and increases
the potential for binding. Remove the bit from the tool, then clean it with
6 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
hot water, kerosene or gum and pitch remover. Never use gasoline. Allow
to dry before using. Discard the bit if the gum or pitch cannot be removed.
4. Do not apply side pressure on the bit unless it is designed for such a
purpose. The bit may bind or break.
5. A loose or mismatched cutting bit may be ejected by the tool, causing an
injury to the user or a bystander. It may also fail to penetrate the material
as the point may move around under pressure, damaging the workpiece.
a. Ensure the cutting bit shank size matches the tool’s chuck or collet size.
b. Tighten the chuck or collet so the shank is tightly held with no room
to move.
KICKBACK PRECAUTIONS
Kickback is a sudden reaction to a pinched or snagged cutting accessory caught
on the material. The material can be ejected and inflict a serious injury on the
user or a bystander. Kickback can also damage the tool or workpiece.
Kickback can be avoided by taking proper precautions:
1. Maintain a firm grip on the material and position your body and arms to
allow you to resist a kickback. Kickback can propel the material in the
direction of the cutting accessory’s rotation.
2. Use special care when working on corners, sharp edges or flexible
material. These workpieces have a tendency to snag the cutting accessory.
3. Only use cutting accessories designed for the tool.
4. Clamp the workpiece to prevent rotation when the drill bit cuts into
the material.
ELECTRICAL SAFETY
WARNING! To reduce risk of electric shock, be certain that the plug is
connected to a properly grounded receptacle.
1. Disconnect tool from power source before cleaning, servicing, changing
parts/accessories or when not in use.
2. Protect yourself against electric shocks when working on electrical
equipment. Avoid body contact with grounded surfaces. There is an
increased chance of electrical shock if your body is grounded.
Visit www.princessauto.com for more information 7

8654337 10 in. Bench-Top Drill Press V 4.0
3. Do not expose tool to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
4. Do not disconnect the power cord in place of using the ON/OFF switch on
the tool. This will prevent an accidental startup when the power cord is
plugged into the power supply.
a. In the event of a power failure, turn off the machine as soon as the
power is interrupted. The possibility of accidental injury could occur if
the power returns and the unit is not switched off.
5. Do not alter any parts of the tool or accessories. All parts and accessories are
designed with built-in safety features that may be compromised if altered.
6. Make certain the power source conforms to requirements of your
equipment (see Specifications).
7. When wiring an electrically driven device, follow all electrical and safety
codes, as well as the most recent Canadian Electrical Code (CE) and
Canadian Centre for Occupational Health and Safety (CCOHS).
8 Grounded tools must be plugged into an outlet that is properly installed and
grounded in accordance with all codes and ordinances. Check with a qualified
electrician if you are in doubt as to whether the outlet is properly grounded. If
the tool should electronically malfunction or break down, grounding provides a
low resistance path to carry electricity away from the user.
a. Never remove the grounding prong or modify the plug in any way, as
this will render the tool unsafe.
b. Do not use any adapter plugs.
9. This device is only for use on 120 V (single phase) and is equipped with a
3-prong grounded power supply cord and plug.
10. DO NOT use this device with a 2-prong wall receptacle.
a. Choose an available 3-prong power outlet.
b. Replace 2 prong outlet with a grounded 3-prong receptacle, installed
in accordance with the CE Code and local codes and ordinances.
WARNING! All wiring should be performed by a qualified electrician.
8 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
POWER CORD
1. Insert the power cord plug directly to the power supply whenever possible.
Use extension cords or surge protectors only when the tool's power cord
cannot reach a power supply from the work area.
2. Do not operate this tool if the power cord is frayed or damaged as
an electric shock or surge may occur, resulting in personal injury or
property damage.
a. Inspect the tool's power cord for cracks, fraying or other faults in the
insulation or plug before each use.
b. Discontinue use if a power cord feels more than comfortably warm
while operating the tool.
c. Have the power cord replaced by a qualified service technician.
3. Keep all connections dry and off the ground to reduce the risk of electric
shock. Do not touch plug with wet hands.
4. Prevent damage to the power cord by observing the following:
a. Do not pull on the cord to disconnect the plug from an outlet.
b. Keep cord away from heat, oil, sharp edges or moving parts.
5. Do not allow people, mobile equipment or vehicles to pass over
unprotected power cords.
a. Position power cords away from traffic areas.
b. Place cords in reinforced conduits.
c. Place planks on either side of the power cord to create a protective trench.
ELECTROMAGNETIC FIELDS FOR DEVICES
WARNING! Shut off the electrical tool or device and move away if you feel
faint, dizzy, nausea or shocks. Seek medical attention.
Electromagnetic Fields (EMF) can interfere with electronic devices such as
pacemakers. Anyone with a pacemaker should consult with their doctor before
working with or near a tool that generates an EMF. The following steps can
minimize the effects of electromagnetic fields.
1. Keep the power source and any power cables as far away from the user as
practical. A minimum of 24 in. is recommended.
Visit www.princessauto.com for more information 9

8654337 10 in. Bench-Top Drill Press V 4.0
2. Avoid long and regular bursts of energy while operating the tool. Use the
tool for short or intermittent periods of time. This will prevent a pacemaker
from interpreting the signal as a rapid heartbeat.
3. Alert other people in the work area, so they can take precautions or can
watch out for those with a pacemaker.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the parts list are included.
ASSEMBLY & INSTALLATION
Numbered references in parenthesis (#1) refer to the included Parts List.
MOUNTING
Secure the tool to a supporting structure before use. Before assembly, bolt the
Base to a flat, level, solid workbench capable of supporting the weight of the
drill press and any workpieces. Verify that installation surface has no hidden
utility lines before drilling or driving screws.
ASSEMBLY
1. Column to Base.
a. Place Column (#6) on the Base (#1) and align bolt holes in the
Column and Base.
b. Attach using Bolt (#5), Washer (#3) and Spring Washer (#4) in each
hole through the Column and into the Base.
2. Table Support.
a. Place the Table Support (#21) over the Rack (#7).
b. Slide the Table Support over the Column (#6).
c. Slide the Collar (#16) over the Column (#6) with the beveled edge
facing down until it presses against the top of the Rack (#7). Tighten
the Set Screw (#17), but do not overtighten it.
10 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
d. Slide the Height Crank (#23) over the Shaft (#24) on the side of the
Table Support (#21). Secure it to the Shaft using the Screw (#22)
against the flat part of the Shaft.
3. Headstock to Column.
a. Loosen the two Set Screws (#17) on the left side of the Headstock
(#67) so they will stay clear while installing it.
b. With the help of an assistant, lift the Headstock above the Column
(#6) and gently slide it down the Column as far as it will go.
c. Tighten the two Set Screws to secure the Headstock in place.
4. Feed Handles / Bars.
a. Thread the Feed Bars (#9) into the Feed Bar Seat (#10) and tighten them.
5. Installing the Chuck.
a. Thoroughly clean the Arbor (#30) and the tapered hole in the Chuck
(#29) of all dirt, grease, oil and protective coatings. Make sure all
parts are thoroughly clean, dry and burr free.
b. Insert the Arbor into the end of the Spindle (#31). If necessary, rotate
the Arbor to ensure that it is correctly positioned and fully inserted
into the Spindle shaft. Firmly tap the Arbor nose with a rubber mallet.
c. Open the jaws of the Chuck to their maximum, using the supplied Chuck Key.
d. Slide the Chuck onto the Arbor nose as far as it will go.
e. Hold a piece of scrap wood against the Chuck nose to protect it and
firmly tap the wood with a rubber mallet to ensure proper seating and
a solid fit of the Chuck on the Spindle.
OPERATION
TOOL SET UP
WARNING! To prevent serious injury from accidental operation. Turn the
Power Switch of the tool off and unplug the tool from its electrical outlet
before performing any procedure in this section.
Visit www.princessauto.com for more information 11

8654337 10 in. Bench-Top Drill Press V 4.0
TABLE ADJUSTMENT
1. Raise or lower the Table by loosening the Pivot Lever (#20) and turning the
Height Crank (#23), clockwise to raise and counterclockwise to lower.
2. Pivot the Table (#26) around the Column (#6) by loosening the Pivot Lever
(#20). The entire Table assembly and Rack (#7), will move as one around
the Column.
3. Tilt the Table by loosening the Angle Bolt (#28) and tilting to the required
angle. The angle can be read using the Angle Scale (#25).
4. To ensure that the drill is entirely perpendicular to the table, insert a straight
round bar (not included) in the chuck (#29), place a square on the Table
(#26) and bring it up to the round bar. Adjust the angle as needed.
5. Make sure the table height and position is set so that the drill travel range
is sufficient for the material to be drilled.
IMPORTANT! To prevent injury from unexpected Table movement, tighten the
Angle Bolt (#28) and Pivot Lever (#20) after adjustment.
SET DRILLING DEPTH
Located around the Spindle Feed Shaft is a Depth Stop Collar with a scale. The collar
is capable of turning about the shaft and may be locked in place by a Locking Screw.
1. Lower the drill (with the power OFF) so that it contacts the material and
hold in that position.
2. Loosen the locking screw and turn the collar so that the measurement for
the depth of the hole required is in line with the pointer.
3. Lock the collar in this position using the locking screw.
CHANGING DRILL SPEED
Before changing the speeds, make sure the machine is switched off and unplugged.
1. Open the pulley cover.
2. Loosen the Motor Tension Knob (#70) on each side of the Headstock (#67)
and move the Motor (#77) towards the Headstock to relieve tension on the
Belts (#43, 80).
3. Consult the chart below and position the Belts (#43, 80) on the Pulleys
(#42, 46, 78) according to the desired drill speed.
12 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
4. When the Belts have been correctly positioned, tighten them by pushing
the Motor away from the Headstock until the belt deflects by approximately
1/2 in. at its center when using reasonable thumb pressure. Lock this
position in with the two Motor Tension Knobs (#70).
5. You can change the drill speed can by repositioning the belts on the spindle
(A) and the motor (B). Chart 1 shows the belt arrangements for each drill
speed. A full chart is also located on the inside of the pulley cover.
DRILL BIT INSTALLATION
1. Insert the drill bit into the jaws of the chuck approximately 1 in., ensuring
that the jaws do not touch the flutes of the drill bit.
2. Before tightening the chuck, ensure that the drill bit is centered within the jaws.
3. Tighten the chuck securely with the included chuck key.
GENERAL OPERATING INSTRUCTIONS
WARNING! If the drill bit grabs and spins the workpiece, do not attempt to
stop the spinning with your hands, as it can cause an impact injury. Step
back and turn the drill press off. Wait for the spindle to stop turning before
dislodging the workpiece.
1. Check that the drilling depth will not allow the bit to touch the table. This
can damage the drill bit.
2. Place the workpiece on the table. Rotate the feed handles to bring the drill
bit down to the wood. Once the workpiece is in the correct position, clamp
it to the table.
a. If drilling a hole through the entire workpiece, place a scrap piece of
wood beneath the workpiece before positioning and clamping. This will
prevent the underside from splintering as the drill bit breaks through.
Chart 1
Visit www.princessauto.com for more information 13

8654337 10 in. Bench-Top Drill Press V 4.0
3 An irregularly shaped workpiece may not lay flat on the table. Block and
clamp it securely as any tilting, twisting or shifting will create a rough drill
hole and may damage the drill bit or drill.
4. Turn the drill press on.
5. Pull down on the feed handle and slowly drill a hole into the workpiece.
6. Once the desired depth is reached, slowly push the feed handle up until the
drill bit clears the workpiece.
7. Turn the drill off. Remove or reposition the workpiece, once the drill bit
stops rotating.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier to
control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components. Only use identical replacement parts when servicing.
a. Examine belt for cracks, tears in the backing and other damage.
Replace damaged belts by following the instructions to install and
tension under Operation - Changing Drill Speed.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
5. Keep the tool handles clean, dry and free from oil/grease at all times.
6. Maintain the tool’s labels and name plates. These carry important information.
If unreadable or missing, contact Princess Auto Ltd. for replacements.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
CLEANING
1. Clean the external surfaces with a cloth after use.
2. Check that all air vents are unblocked.
3. Blow out the motor of accumulated sawdust with compressed air.
14 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
LUBRICATION
NOTICE! NEVER use a penetrating oil to lubricate the tool. Penetrating oil
may act as a solvent that can break down the grease and cause the tool to
seize up.
Inspect and lubricate the tool when required. Lubricate the table support
mechanism, rack and spindle splines. Ball bearings are factory packed with
grease and do not require lubrication.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
Visit www.princessauto.com for more information 15

8654337 10 in. Bench-Top Drill Press V 4.0
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function properly
or parts are missing. If unable to do so, have a qualified technician service the tool.
Problem(s)
Possible Cause(s)
Suggested Solution(s)
Tool will not
start.
1. Power Cord not connected.
2. No power at outlet.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or
component wear.
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is
unpowered, turn off tool and check
circuit breaker. If breaker is tripped,
make sure circuit is right capacity for
tool and there are no other loads on
the circuit.
3. Turn off tool and allow to cool. Press
reset button on tool until it clicks.
4. Have technician service tool.
Tool operates
slowly.
Extension cord too long or wire
size too small.
Eliminate use of extension cord. If an
extension cord is needed, use one with
the proper diameter for its length and
load.
Performance
decreases
over time.
1. Accessory dull or damaged.
2. Carbon brushes worn or
damaged.
1. Keep cutting accessories sharp.
Replace as needed.
2. Have qualified technician replace
brushes.
Excessive
noise or
rattling.
1. Internal damage or
component wear.
2. Belt too loose (slipping) or
too tight (bearing damage).
1. Have technician service tool.
2. Properly tension belt.
Overheating. 1. Forcing machine to work too
fast.
2. Accessory dull or damaged.
3. Blocked motor housing vents.
4. Motor strained by long or
small diameter extension
cord.
1. Allow machine to work at its own rate.
2. Keep cutting accessories sharp.
Replace as needed.
3. Blow dust out of motor using
compressed air.
4. Eliminate use of extension cord. If an
extension cord is needed, use one with
the proper diameter for its length and
load.
16 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
PARTS BREAKDOWN
Visit www.princessauto.com for more information 17

8654337 10 in. Bench-Top Drill Press V 4.0
PARTS LIST
PART# DESCRIPTION QTY
1 Base 1
2 Column Support 1
3 Flat Washer 8 7
4 Spring Washer 7
5 Bolt M8 × 25 3
6
Column
1
7 Rack 1
8 Feed Handle 3
9 Feed Bar 3
10 Feed Bar Seat 1
11 Pin 5×30 1
12 Shaft Pinion 1
13 Depth Scale 1
14 Depth Stop 1
15
Fastening Knob
1
16 Collar 1
17 Set Screw M8 × 10 3
18 Axle 1
19 Gear 1
20 Table Pivot Lever 1
21 Table Support 1
22 Screw M6 × 12 5
23 Height Crank 1
24 Shaft 1
25 Angle Scale 1
26 Table 1
27 Spring Washer 12 1
28 Angle Bolt M12 × 30 1
29 Chuck 1
30 Arbor 1
31 Spindle 1
32 Ball Bearing 6201 1
33 Spindle Sleeve 1
34 Key 1
35 O-Ring 1
36 Ball Bearing 6005 1
37 Retaining Ring 12 1
38 Retaining Ring 42 2
39 Ball Bearing 6004 2
40 Bushing 1
41 Internal Spindle
Sleeve
1
42 Spindle Pulley 1
43 V-Belt 0-480 1
44 Nut M20 × 1.5 1
45 Retaining Ring 32 1
46 Middle Pulley 1
47 Pulley Adjuster 1
48 Knob 1
49
Flat Washer 6
4
50 Flat Washer 5 3
51 Screw M5 × 10 5
52 Screw M6 × 10 2
53 Pulley Cover 1
54 Wire Clamp 2
55 Nut M6 2
56 Rubber Pad 4
57 Tension Spring 1
58 Spring Cap 1
59 Nut M12 × 1.5 2
60 Power Cord 1
18 For technical questions call 1-800-665-8685

V 4.0 10 in. Bench-Top Drill Press 8654337
PART#
DESCRIPTION
QTY
61
Screw ST2.9 × 10
3
62 Switch Cover 1
63 Power Switch 1
64 Switch Box 1
65 Nut M8 1
66 Screw 1
67 Headstock 1
68 Depth Pointer 1
69 Round Pin 1
70 Knob 2
71
Motor Support
2
72 Flat Washer 10 4
73 Bolt M8 × 20 4
74 Motor Bracket 1
75 Spring Washer 10 2
76 Nut M10 2
77 Motor 1
78 Motor Pulley 1
79 Screw M6 ×10 1
80 V-Belt 0-450 1
Visit www.princessauto.com for more information 19

Perceuse à colonne
d'établi de 10 po