Power Fist 8083362 User manual

18V 4 pc Combo
Cordless Tool Kit
8083362
OWNER'S MANUAL
Read and understand all instructions before use.
Retain this manual for future reference.

8083362
18V 4 pc Combo
Cordless Tool Kit
General Instructions and Battery Charging
Please read these instructions fully before use.
BEFORE INSERTING THE BATTERY INTO ANY OF THE TOOLS
• Ensureanyttings(egsawblades)havebeenxedrmlyandthatanyadjustmentdevices(eghex
wrench)havebeenremoved
• Ensuretherelativefastenershavebeensecuredtightlyinplaceandtheworkpieceisadequatelysecured
• Alwaysensurethebatteryisdisconnectedbeforemakinganyadjustments
Power connection
•Thefuseinthepowercordonthechargershouldalwaysbereplacedwithoneofidenticalrating.Check
thatthevoltagegivenonthechargermatchesthesupplyvoltage.
Charge and battery
• Thechargerandthetoolsinthispackarespecicallydesignedtoworktogether.Donotattemptto
usethetoolswithanyotherchargerorbatteryotherthanthechargerandbatterysuppliedwiththese
products.IdenticalreplacementandextrabatteriesareavailableatyournearestPrincessAutolocation,
item#8083388.
• Note:Thebatteryissuppliedunchargedfromthefactory.Itwillbenecessarytochargethebatterybefore
use.Toprolongbatterylife,avoidleavingthebatteryonchargeforlongerthan24hours.Over-charging
isnotasafetyconcern,butitcanreducethelifespanofthebattery.Donotchargeabatterycolderthan
4°C.Betweencharges,restthechargerforatleast15minutes.Inawarmenvironment,orafterheavyuse,
thebatterypackmaybecometoohottopermitcharging.Allowtimeforthebatterytocooldownbefore
recharging.Whenthebatteryischargedforthersttime,orafterprolongedstorage,thebatterywillonly
acceptabouta60%charge.However,afterseveralchargeanddischargecycles,thebatterywillaccepta
100%charge.
• Tochargethebattery,insertthebatterypackinthecharger.Plugthechargerintoapoweroutletandpress
the‘set’buttononthecharger.
Driver/drill parts identication
a) On/offtriggerswitch
b) Forward/reverseswitch
c) 16positiontorquecontrol
d) Keylesschuck
e) Double-endedbit
For any technical questions, please call 1-800-665-8685
2

Specications
• 18VNi-CADbattery
• 0to900RPM
• 3/8"keylesschuck
Changing the saw blade
• First,becomefamiliarwiththesawcomponentsandtheirset-up.Undothebladeretaininghexscrew
usingthesuppliedhexwrench.Removethescrew,pulloffthebladeclamp,andthebladetobe
replaced.Placethenewsawbladeintothelargerslotontheclampandaligntheholeinthejigsaw
bladewiththeholeintheclamp.Placethejigsawandclampassemblyontothemotorarm,making
sureall3holesarealigned.Insertthehexscrewandtighten.Ensurethejigsawbladeteetharefacing
outward.
Cutting angle
• Thebaseplateofthejigsawcanrotateupto35°forangledcuts.Toadjustthecuttingangle,loosen
thebaseplateangleadjustmentscrew.Tiltthebaseplatetothedesiredangle.Retightenthe
adjustmenthexscrew.
Cutting
• Beforeuse,ensurethattheworkpieceisclampedrmlyinplace.Depressthetriggerlockingbutton
andtheon/offtriggersimultaneouslytobeginbladeoperation.Allowthebladetocometofullspeed
beforestartingacut.
Detail sander parts identication
a) On/offtrigger
b) Handle
c) Sandingplate
d) Hookandloopsandingpad
e) Batterypacklocation
For any technical questions, please call 1-800-665-8685
3

Specications
•18VDCmotor
•7,000OPM(orbitsperminute)
•3-1/2"x3-1/2"x3-1/2"sandingpads
Sander operation
•Attention:Ensuretheswitchisoffandthebatterydisconnectedbeforemakinganyadjustmentsor
repairs,orstoringthesander.
•Donotstoreinlocationswherethetemperaturemayreachorexceed50°C.
•Thetriangularbaseofthedetailsanderiscoatedwithhooks,thesandingpadsarecoatedonthenon-
abrasivesidewithloops.Thismakesitquickandeasytoreplacesandingpads.Thesandingpadmust
alignperfectlyontothesandingplate.
•Whenthepadisinposition,thesanderisreadytooperatebypressingtheon/offtrigger.
Flashlight Operation
•Insertbatteryintoashlightslotandsecure.
•Slidetheswitchonthehandleto1ofthe2brightnesspositions.
•Slidetheswitchtotheoffpositiontoturnoff.
For any technical questions, please call 1-800-665-8685
4