Power Hawk AUTO CRIB-IT AC-14 User manual

Rockaway, New Jersey USA Rev F 3/2013
INSTRUCTION MANUAL
For
MODELS AC-14 and AC-17
AUTO CRIB-IT™ Description
CONGRATULATIONS on your purchase of the AUTO CRIB-IT™!!... the easiest and
quickest vehicle stabilization tool on the market! Lightweight and portable, this tool can
be positioned and operated to automatically extend and stabilize vehicles in seconds.
Use it for auto-extrication and other stabilization operations, up to a maximum load of
2000 lbs for the AC-14 and 2800 lbs for the AC-17! The AUTO CRIB-IT is patented and
utilizes gas-spring actuated extender plates that automatically rise to engage the
working material and lock into place. Because the AUTO CRIB-IT is gas-spring-loaded,
it will self-adjust upward and lock as weight is removed from the vehicle. The AUTO
CRIB-IT can also be placed completely under and parallel to rocker panels to avoid trip
hazards. Because the tool is made from high-strength aluminum and other metal parts,
the AUTO CRIB-IT is easily decontaminated. Its super compact design makes it easy
to stow and can free up room for other vital equipment.
Model AC-14 Model AC-17

AUTO CRIB-IT INSTRUCTION MANUAL Page 2 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
The components of the AUTO CRIB-IT are shown below for each model. Refer to these terms
throughout this instruction manual.
MODEL AC-14
A. Channel Base (P/N 2C0903-1)
B. Fixed Extender Plate (P/N 2C0904-1)
C. Moveable Extender Plate (P/N 2C0905-1)
D. Hinge (P/N 2C0913-1)
E. Angle Supports
F. Slide Bracket Pin (P/N 2C0906-1)
G. Pin (P/N 2C0915-1)
H. Gas Piston Spring Kit (P/N C16-29759)
I. Handle (P/N 2C0912-1)
J. Lock (P/N PHT1820A26)
K. Bottom Grip Surface (P/N PHT6970T151)
A
B
C
D
F H
G
J
I
E
K
MODEL AC-17
A. Channel Base (P/N 2C0931-1)
B. Fixed Extender Plate (P/N 2C0932-1)
C. Moveable Extender Plate (P/N 2C0933-1)
D. Hinge (P/N 2C0913-1)
E. Angle Supports
F. Slide Bracket Pin (P/N 2C0934-1)
G. Pin (P/N 2C0935-1)
H. Gas Piston Spring Kit (P/N C16-29760)
I. Handle (P/N 2C0912-1)
J. Lock (P/N PHT1820A26)
K. Bottom Grip Surface (P/N PHT6970T153)
K
A
B
C
D
F
H
G
J
I
E
G
G

AUTO CRIB-IT INSTRUCTION MANUAL Page 3 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
General Safety Information
The AUTO CRIB-IT is designed to provide safe operation. All users should read and be thoroughly familiar
with the operating instructions and safety precautions contained in this manual. Operator safety depends on
users being properly trained by the Authority having jurisdiction and using the tool for the purpose intended.
The following safety precautions must be observed at all times. FAILURE TO DO SO COULD RESULT IN
PERSONAL INJURY, DAMAGE TO PROPERTY AND/ OR EQUIPMENT:
The AUTO CRIB-IT™ shall only be operated by persons authorized by the Authority Having
Jurisdiction.
Personal protective equipment (PPE) shall be worn as directed by the Authority Having Jurisdiction.
At a minimum, this should include gloves, helmet, eye protection, steel-toed footwear, and body
protection, such as turnout gear.
This tool is SPRING-LOADED and can rapidly extend automatically when unlocked. Keep face,
hands, and other body parts away from moving parts.
DO NOT EXCEED MAXIMUM LOAD RATINGS (AC-14: 2000 LBS., AC-17: 2800 LBS.)
Apply load ONLY to the top Angle Supports
Prior to use, inspect all AUTO CRIB-IT™ components for any signs of damage. Do not use damaged
equipment.
Stow in the retracted position with the AUTO CRIB-IT lock engaged.
Channel Base bottom grip surface is extremely coarse and can scratch surfaces. Avoid contact with
such surfaces to prevent unwanted scratches.
Stay alert. Do not operate tool when tired.
Use only Factory authorized service parts.
AUTO CRIB-IT Operation
Note: Model AC-14 is used for the following step-by-step instructions which are the same for Model AC-17.
1. Determine the engagement point(s) on the vehicle for proper stabilization.
Minimum starting clearances:
Model AC-14: Approx. 5-3/4 inches
Model AC-17: Approx. 8-1/4 inches
NOTE: Because of the AUTO CRIB-IT’s retractable design, you can use engagement points
under the rocker panel and on the vehicle’s frame.
2. Determine the AUTO CRIB-IT orientation for proper stabilization (i.e. perpendicular or parallel to
the rocker panel)
Per
p
endicular Parallel
Starting
Clearance

AUTO CRIB-IT INSTRUCTION MANUAL Page 4 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
CAUTION: Always stow and carry the AUTO CRIB-IT in the locked position
3. With the AUTO CRIB-IT lock still engaged, position the
tool under the vehicle so that when extended,
the Angle Supports will contact the desired
engagement point.
4. Disengage AUTO CRIB-IT Lock by turning the knob Clockwise as shown below. Be sure to hold
the top plates down against the Channel Base to prevent unintended automatic extension.
NOTE: As the AUTO CRIB-
IT rises, the relative position
of the Angle Supports will
move toward the rear (fixed
side) of the tool as shown on
Approx. 5 inches for Model AC-14
and 9 inches for Model AC-17

AUTO CRIB-IT INSTRUCTION MANUAL Page 5 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
The Top Plates are SPRING-LOADED and can rapidly extend
automatically when unlocked. Keep face, hands, and other body
parts away from moving parts.
5. Start automatic operation of the
AUTO CRIB-IT by slightly lifting
the top plates. CAUTION: DO
NOT lift from above the Angle
Supports. The spring action
will cause the tool to rise and
the Slide Pin to ratchet across
the slots in the Channel Base
until the Angle Supports contact
the engagement point. The
slide pin and channel slot
provides no-back locking of the
AUTO CRIB-IT.
6. Inspect the AUTO CRIB-IT engagement to ensure it is secure and has properly stabilized the
vehicle.
NOTE: As weight is removed from the vehicle, the vehicle’s suspension may cause its body
to lift. In this circumstance, the AUTO CRIB-IT will automatically rise with the body and lock
to the new height (provided the height is within the maximum extension of the tool).
DO NOT EXCEED MAXIMUM LOAD RATINGS
Model AC-14: 2,000 LBS. MAX LOAD
Model AC-17: 2,800 LBS. MAX LOAD
Failure to do so may result in breakage of components and may cause
serious personal injury, damage to property and/or equipment.
HINT: Raising the
vehicle suspension
manually will bring the
AUTO CRIB-IT to a
higher notch to provide
tighter engagement.
Correct Wrong
!
!
WARNING

AUTO CRIB-IT INSTRUCTION MANUAL Page 6 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
TO REMOVE AUTO CRIB-IT…
7. Hold the AUTO CRIB-IT handle down to prevent further extension and remove the applied load
from the Angle Supports.
8. Once the load is removed, lift the AUTO CRIB-IT handle upward to clear the slide pin from the
slots in the Channel Base and pull outward (toward the front of the AUTO CRIB-IT), while
pushing down on the Moveable Plate with your other hand at the same time. HINT: Apply toe
pressure to the front of the Channel Base to prevent the entire tool from moving.
NOTE: Avoid getting debris in between the Angle Supports which could get jammed and
prevent retraction.
9. Make sure Top Plates are all the way down and resting on the Channel Base. Re-engage AUTO
CRIB-IT Lock by turning the knob Counter-Clockwise as shown below. Test by pulling up on the
Top Plates to ensure the lock is properly engaged.
Toe
Pressure
Locking
Tab
Engaged
Make sure that the ¼-Turn Lock is in the UN-LOCKED
position when retracting the AUTO CRIB-IT. Failure
to comply will not allow the Top Plates to become
fully retracted and can cause the Locking Tab to
become loaded and bent. If the Tab becomes bent,
use pliers to straighten so that it properly engages
the upper part of the Channel slot when in the
LOCKED position.
!CAUTION
WRONG!
When Retracting

AUTO CRIB-IT INSTRUCTION MANUAL Page 7 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
10. Remove the AUTO CRIB-IT
from underneath the
vehicle. Stow using the
Velcro strap that is provided
to prevent accidental
release and extension.
RAISING THE AUTO CRIB-IT STARTING HEIGHT…
If maximum extension of the AUTO CRIB-IT is reached before sufficiently engaging and stabilizing the
vehicle, the starting height of the AUTO CRIB-IT may be raised by using proper block cribbing methods.
At a minimum, the AUTO CRIB-IT Channel Base must engage the block cribbing at three (3) points…
One at each end and one in the center as shown below:
Maintenance
Proper care and maintenance of the AUTO CRIB-IT is necessary to ensure long tool life and safe operation.
Interval Check Instructions
After Each Use Make sure all
fasteners are tight
Tighten as necessary.
Top Hinge Bolts (x8): 30-40 Foot-Pounds
Slide Pin Bolts (x3): 30-40 Foot-Pounds
Handle Screws (x4): 40-50 Inch-Pounds
¼-Turn Lock Hex Nut (x1): 65-75 Inch-Pounds
¼ Turn Lock Cam Screw (x1): 10-15 Inch-Pounds
Make sure AUTO
CRIB-IT locking
mechanism for
stowing is engaging
properly
Engage AUTO CRIB-IT Lock and attempt to lift top plates.
Top plates should not be able to lift.
Check for bent,
damaged or cracked
parts.
Replace parts as necessary.
NOTE: A bent Slide Pin or Fixed Pin would indicate that the
AUTO CRIB-IT was overloaded.
Monthly Check for smooth
automatic operation
Apply WD-40 (or equivalent) to slide pin, fixed pin, channel
base slots, and hinge.
Annually Check for sufficient
spring action
Replace gas spring piston assembly as necessary.
Per
p
endicular Parallel
Velcro
Strap

AUTO CRIB-IT INSTRUCTION MANUAL Page 8 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
Troubleshooting
Problem Possible Cause Solution
Extender Plates will not
rise automatically
Maximum extension has been
reached
Use block cribbing underneath the channel base
to raise the AUTO CRIB-IT starting height.
Ensure block cribbing supports the channel base
at a minimum of three points along its length
(each end and in the center). See section on
“Raising AUTO CRIB-IT Starting Height”.
Moving parts are dry and
require lubrication
Apply WD-40 generously to slide pin, fixed pin,
channel base slots, and hinge.
Insufficient gas-spring
pressure
Replace gas spring assembly.
Parts are damaged Determine damaged parts and replace as
necessary.
NOTE: A bent Slide Pin or Fixed Pin would
indicate that the AUTO CRIB-IT was overloaded.
Extender Plates will not
retract.
Load is still applied to the
AUTO CRIB-IT
See instructions on removing AUTO CRIB-IT
Slide pin is still engaged in
channel base slot
See instructions on removing AUTO CRIB-IT
Material or debris is lodged in
between Angle Supports
Remove material or debris from Angle Supports.
See instructions on removing AUTO CRIB-IT
If the above does not correct problem, contact your authorized AUTO CRIB-IT Dealer or the Factory.
Replacement Parts: Replacement parts for the AUTO CRIB-IT can be obtained from your authorized
AUTO CRIB-IT Dealer or by contacting the Factory.
Specifications Model AC-14 Model AC-17
Maximum Load: 2,000 lbs. (8.9 kN) 2,800 lbs. (12.4 kN)
Fully Extended Height: 13 in. (33.0 cm) 17 in. (43.2)
Weight: 14.5 lbs. (6.6 kg) 23.5 lbs. (10.7 kg)
Stowed Dimensions (LxWxH): 28 in. x 4 in. x 2-3/4 in. 36 in. x 6 in. x 3 in.
(71.1 cm x 10.2 cm x 7 cm) (91.4 cm x 15.2 cm x 7.6 cm)
NOTE: The Angle Supports add 1-3/8 inches (3.5 cm) to the height at the center
The AUTO CRIB-IT™ is manufactured by:
POWER HAWK
®Technologies, Inc.
300 Forge Way, Suite 2, Rockaway, New Jersey 07866 USA
1-800-PWR-HAWK (1-800-797-4295) or 973-627-4646 Fax: [phone]
www.powerhawk.com
“Power Hawk” is a Registered Trademark of Power Hawk Technologies, Inc.
“AUTO CRIB-IT” is a Trademark of Power Hawk Technologies, Inc.

AUTO CRIB-IT INSTRUCTION MANUAL Page 9 of 9
POWER HAWK TECHNOLOGIES INC., Rockaway, New Jersey USA Rev F 3/2013
WARRANTY
WARRANTY. Power Hawk Technologies, Inc. guarantees the AUTO CRIB-IT, parts, equipment and
accessories against defects in material and workmanship for a period of one (1) year from the date of
purchase by the original purchaser. The identity of the original purchaser and the date of purchase shall be
established in each case by the return of the properly completed Warranty Registration Card.
WARRANTY TERMS. The obligations of Power Hawk Technologies, Inc. under this warranty include free
replacement of the necessary parts and the shipping costs to return the equipment to the user, provided the
inspection of the equipment has proved that the parts were defective at the time of purchase or were
improperly designed or manufactured. The warranty inspection can only be performed by a Power Hawk
Technologies, Inc. service center or an official Power Hawk Technologies, Inc. factory-trained distributor, and
shipping costs to a Power Hawk Technologies, Inc service center or an official Power Hawk Technologies,
Inc. factory-trained distributor will be for purchaser’s account. Said warranty shall remain in effect only if (1)
such goods are used normally and properly in accordance with Power Hawk Technologies, Inc. instructions
as to maintenance and operation, whether given orally or set forth in manuals and instruction sheets furnished
by Power Hawk Technologies, Inc. and (2) the purchaser gives prompt notice to Power Hawk Technologies,
Inc. of any such defects and preserves and turns over all allegedly defective goods, parts or items.
EXCLUSIONS. This warranty covers all defects in material and workmanship except:
Any damage occurring during shipments of the goods (for which claims shall be presented to the
carrier).
Normal wear and tear and deterioration.
Damage caused by abuse, improper use, or corrosion
Damage caused by repairs performed by persons other than a Power Hawk Technologies, Inc.
service center or an official Power Hawk Technologies, Inc. factory-trained distributor, or damage
resulting from the use of parts other than genuine Power Hawk Technologies, Inc. parts.
Damage as a result of improper or neglected reasonable maintenance.
THIS WARRANTY STATED HEREIN IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WRITTEN OR ORAL, EXPRESS, STATUTORY OR IMPLIED, AND POWERHAWK TECHNOLOGIES, INC.
EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES FOR MERCHANTABILITY, FITNESS,
PERFORMANCE OR SUITABILITY FOR A PARTICULAR PURPOSE.
LIMITATION OF DAMAGES. Power Hawk Technologies, Inc.’s obligation under this warranty is limited to
repair and/or replacement, at Power Hawk Technologies, Inc.’s option, of any defective Power Hawk
Technologies, Inc. tool, part, accessory or item or other manufacturer’s tool, part, accessory or item, and
under no circumstances, whether due to a breach of any warranty hereunder or any other cause, and whether
arising in contract or in tort (including negligence or strict liability) shall Power Hawk Technologies, Inc. be
liable for (1) consequential or indirect loss or damage including, but not limited to, loss of profits, loss of
production, plant downtime, or liabilities to customers or other third parties, or (2) loss or damage arising out
of the sale or contributory negligence of the purchaser, its employees or agents, or any third part, or (3) any
special or punitive damages of any nature. If Power Hawk Technologies, Inc. determines, in its sole and final
discretion, that the nature of the defect precludes remedy by repair and/or replacement Power Hawk
Technologies, Inc. reserves the right to satisfy any warranty obligation by refunding the full purchase price, on
return of all defective goods to Power Hawk Technologies, Inc., shipping cost prepaid. Any action for breach
of warranty or other action must be commenced within one (1) year after such cause of action arises, except
where applicable law would prohibit any such time restriction in bringing of such an action.
NOTICES. For all notices, information and inquiries concerning this warranty or Power Hawk Technologies
Inc. service centers and official Power Hawk Technologies, Inc. factory-trained distributors contact:
Power Hawk Technologies, Inc.,
300 Forge Way, Suite 2
Rockaway, New Jersey 07866 USA
Telephone: [phone] or 1-800-PWR-HAWK (1-800-797-4295)
Fax: [phone]
Email: [email protected]