PowerAcoustik PTID-3600 User manual

PTID-3600/ PTID-3600T
In-Dash 3.6” Monitor
Touch Sensor
DVD/CD/MP3/MP4
MW/FM Radio
Built-in TV tuner
Owner’s Manual
Take the time to read through this owner’s manual.
Familiarity with installation and operation procedures will help you obtain the best
Performance from your new DVD-receiver.

Page - 1
Table of Contents
Table of Contents.......................................................................................................................1
Important Safeguards.................................................................................................................2
Accessories .......................................................................................................................3
Installation/Un-Installation ..............................................................................................................4
Wiring Connections.......................................................................................................................5
Detachable Control Panel ........................................................................................................6
Panel Controls……………..........................................................................................................7
IR Remote Controls ........................................................................................................................8
General Operations....................................................................................................................9
Digital Tuner...................................................................................................................................12
Memory Card/ USB Operations.................................................................................................. 12
Disc operations.................................................................................. ...........................................15
MP3 overview.............................................................................. ............................................18
TV OPERATIONS.......................................................................... ............................................19
Compatible Files ............................................................................................................................ 20
SETUP Menu ......................................................................................................................20
Other Functions..................................................................................... ..........................................22
Anti-theft system.................................................................................... ........................................22
Note on Discs................................................................................ .............................................23
Troubleshooting Guide ..............................................................................................................24
Specification.............................................................................................................................25

Page - 2
Important Safeguards
zUsing the device at temperature below -10 may cause the breakage of the device. BEFORE℃
USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED
TEMPERATURE!
zRead carefully through this manual to familiarize yourself with this high-quality sound system.
zDisconnect the vehicle's negative battery terminal while mounting and connecting the unit.
zWhen replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with
a higher amperage rating may cause serious damage to the unit.
zDO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to
the eyes.
zMake sure that pins or other foreign objects do not get inside the unit; they may cause
malfunctions, or create safety hazards such as electrical shock or laser beam exposure.
zIf you have parked the car for a long time in hot or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
zDO NOT open covers and do not repair yourself. Consult the dealer or an experienced
technician for help.
zMake sure you disconnect the power supply and aerial if you will not use the system for a long
period or during a thunderstorm.
zMake sure you disconnect the power supply if the system appears to be working incorrectly,（e. g,
making unusual sounds, smelling strange, emitting smokes from inside or liquid having gotten
inside it）Have a qualified technician check the system.
zThe unit is designed for negative terminal of the battery, which is connected to the vehicle metal.
Please confirm it before installation.
zDo not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it
may overload or burn out the power amplifier.
zDo not install the detachable panel before connecting the wire.
zDon't remove the detachable panel when encoding.

Page - 3
Accessories
Package contains the following accessories for installation and operation of the unit.
(1) Washer, Spring
Washer, M5 Nut 1 each
(2) Mounting Strap 1
(3) Screw 1
(4) Bolt 4
(5) Mounting Collar 1
(6) Release Key 2
(7) Rubber Cushion 1
AV in Cable Panel Carrying Case
Owner’s Manual Remote Controller

Page - 4
Installation/Un-Installation
First complete the electrical connections, and then check them for correctness.
Installation
This unit can be installed in any dashboard having an opening as shown on the picture. The
dashboard should be 4.75 – 5.56 mm thick in order to be able to support the unit.
1. Insert mounting collar into the dashboard, and bend the mounting tabs out with a screwdriver.
Make sure that lock lever（※）is flush with the mounting collar (not projecting outward).
2. Secure the rear of the unit.
After fixing mounting bolt and power connector, fix the rear of the unit to the car body by rubber
cushion.
3. Insert trim plate.
When you prepare to insert trim plate, please check its direction. Once it was up side down, it
cannot be fixed.
Un-installation
Remove Trim Ring and insert Release Keys into left and right side-end holes as shown in below
picture and pull the unit out of the dashboard.
Lock lever（※）

Page - 5
Wiring Connections
Make sure you have good chassis ground. A good ground connection will eliminate most electrical
noise problems. A good
chassis ground requires a
tight connection to the
vehicle’s metal chassis.
The area around the
ground connection should
be clean, bare metal
without rust, paint, plastic,
dust, or dirt for a good
electrical connection.
**TV antenna is for
PTID-3600T only.
Caution: Do not
interchange the connection
of the wiring!!!
For some car models you
may need to modify wiring
of the supplied power cord.
Contact your authorized
car dealer before installing
this unit.
Using the ISO Connector
1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated.
2. For connections without the ISO connectors, check the wiring in the vehicle carefully before
connecting, incorrect connection may cause serious damage to this unit.
3. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the
color code table below for speaker and power cable connections.
Location Function
Connector A Connector B
1 Rear Right(+)---Purple
2 Rear Right(-)---Purple/Black Stripe
3 Front Right(+)---Grey
4 Battery 12V
(+)/yellow Front Right(-)---Grey/Black Stripe
5 Auto Antenna/blue Front Left(+)---White
6 Front Left((-)---White/Black Stripe
7 ACC+/red Rear Left(+)---Green
8 Ground/black Rear Left(-)---Green/Black Stripe

Page - 6
Detachable Control Panel
Detaching the control panel
zTurn the Power off.
zPress OPEN button release the panel.
zPull the panel out.
Attaching the control panel
zInsert the left side of the control panel into the main unit.
zPress the control panel right side until the “click” sound is heard.
Caution:
DO NOT insert the control panel from the right side. It can damage the control panel.
The control panel can easily be damaged by shocks. After removing it, place it in a protective case
and be careful not to drop it or subject it to strong shocks.
The rear connector that connects the main unit and the control panel is an extremely important part.
Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.
Note:
If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in
isopropyl alcohol to clean the socket on the back of the control panel.

Page - 7
Panel Controls
Front panel
1. AUX IN 2. POWER/ MUTE 3. IR sensor 4. AS/PS 5. SEL
6. VOL + 7. PLAY/PAUSE 8. MENU 9. TFT display 10. OPEN
11. MODE 12. PREVIOUS 13. VOL 14. OK 15. NEXT
16. BAND 17. USB
18. Memory Card slot
19. EJECT button
20. Disc slot
21. RESET
22. Flashing LED

Page - 8
IR Remote Control
REPLACING THE BATTERY
Remote Control comes with a CR-2025 Lithium Battery included.
1. Remove the Battery Holder from the back of the Remote Control.
2. Insert a CR-2025 Lithium battery with the positive (+) mark upward. Insert the Battery Holder into
the back of the Remote Control.
Warning: Store the battery where children cannot reach. If a child accidentally swallows the battery,
consult a doctor immediately.
+3V
(CR 2025)
1. MODE
2. POWER
3. BND/RDM
4. ENTER
5. Cursor / / /
6. STEREO/MONO
7. LOC/ PROG
8. P.SCN/RPT
9. SEEK-/
10. LOUD
11. OSD
12. STOP/ PBC
13. Digit 0-9
14.
15. MUTE
16. MENU
17. SUB-T
18. SETUP
19. ANGLE
20. INT
21. VOL+
22. A-B/ZOOM
23. SEL
24. SEEK+/ 
25. VOL-
26. AUDIO/ GOTO

Page - 9
Do not re-charge, short, disassemble or heat the battery or dispose it in fire.
Do not expose or bring into contact the battery with other metallic materials. Doing this may cause
the battery to give off heat, crack or start a fire.
When throwing away or saving the battery, wrap it in tape and insulate; otherwise, the battery may
give off heat, crack or start a fire
General Operations
Reset the Unit
In case the unit is malfunctioned or need to reset to factory default setting, press RESET button in
inner panel then the unit will be reset.
Power on/off
Press “POWER” button to turn on the unit.
Long press POWER button on front panel or press POWER button on RC to power off the unit.
Mode Setting
Press MODE button on front panel or remote control to change mode in a sequence of: Tuner
=>DVD =USB =>Memory Card =>TV=> AV IN=> Tuner
(When DVD/USB/ Memory Card available.)
Menu button
Press to enter MENU setting. Long Press Menu button on remote control can back to Main Menu.
Band button
In radio mode, press to select FM1-FM2-FM3-MW.In DVD mode, if playback mp3/wma files or
contents of multi folders, press to move cursor right side, long press to move cursor
downside.
OK button
In playing DVD mode, short press to enter and confirm;
In playing Radio mode, short press to enter and confirm;
SEL button
In playing DVD mode, short press to select the audio setting.
In playing Radio mode, short press to select manual storage stations，long press to select the audio
setting
Volume Control
Turn the knob on front panel clockwise/ counter-clockwise or press VOL+/- button on remote control
to increase/ decrease the volume level.
MUTE Function
Short press POWER/MUTE button on the panel or press MUTE button on the Remote Control to
mute. Press it again to cancel mute.

Page - 10
Audio Setting
Press SEL button on the Remote Control to select the audio setting (or on front panel, long press
SEL button in radio mode, short press SEL button in other mode to select the audio setting)
BASS =>TREBLE => BALANCE => FADER => EQ.
Press /buttons on remote to select the audio setting item (or press the VOL knob on front panel
to select the setting item).
Press ENTER button or button on remote control or OK button on front panel to enter the
selected
item.
Press /buttons on remote to adjust the audio setting data (or press the knob on front
panel to adjust the setting data).
Press SEL button on remote again to save the setting data and return to current mode.
Notes: If turn off the power, all the settings of each mode will be saved.
- If turn off the battery power, all the settings will be clear and become factory default setting.
- If you don’t adjust setting within 3 seconds after selecting the desired setting item, the unit will
automatically return to the current mode.
Menu Settings
Press MENU button on front panel or remote control to enter MENU setting.
During FM mode press the MENU button to enter the setting mode.
Press /buttons on the remote control or press the knob on front panel to select the setting.
Press ENTER button or button on remote control or OK button on front panel to enter the setting.
Press /buttons on remote control or press the knob on front panel to adjust the
setting.
Press ENTER button or button on remote control or OK button on front panel to confirm, press
MENU to return to last settings list.
•In Radio mode short and repeat press the OK button to select these settings:
AUDIO=> EXPERT => CLOCK
In USB/ Memory Card mode short and repeatedly press the OK button to select these settings:
AUDIO => PICTURE => EXPERT => CLOCK
zAUDIO MENU
MENU DESCRIPTION(tuning by left or right arrow)
BASS Support 10 levels. Default level is 0.
TREBLE Support 10 levels. Default level is 0.
BALANCE Support 10 levels for each left and right channel. Default is left equal to right.
FADER Support 10 levels for each front and rear channel. Default is front equal to rear.
EQ DSP OFF FLAT→CLASSICS→POP→ROCK→DSP OFF

Page - 11
zPICTURE MENU
MENU DESCRIPTION
RED Adjust level of red color. Support 50 levels. Default level is 25.
GREEN Adjust level of green color. Support 50 levels. Default level is 25
BLUE Adjust level of blue color. Support 50 levels. Default level is 25.
BRIGHTNESS Adjust level of screen brightness. Support 50 levels. Default level is 25
CONTRAST Adjust level of screen contrast. Support 50 levels. Default level is 25.
SHARPNESS Adjust level of screen sharpness. Support 15 levels. Default level is 10
SCREEN Adjust screen size: 16:9 →4:3→FULL
COLOR
RESET
Resume color default status. (Select YES or NO by navigation buttons, and
press ENTER button on remote control or OK button on front panel to confirm
“YES”)
zEXPERT MENU
MENU DESCRIPTION
DX Set search radio station by DX or LOCAL mode.
DX→LOCAL
STEREO Set radio audio at STEREO or MONO mode, STEREO→MONO
BEEP Set press keys‘ sound. 2ND→ALL→OFF
LOUD Set loudness on or off. OFF→ON
SUBWOOFER Set subwoofer ON→OFF
BACKLIGHT Set OSD BACKLIGHT: HIGHT→LOW →MID
OSD COLOR Set OSD COLOR:DARK BLUE→VIOLET→LIGHT BLUE
zCLOCK MENU
MENU DESCRIPTION
CLOCK Set CLOCK display time or not. Off / on.
CLOCK HOUR SET CLOCK 12H/24H
CLOCK
ADJUST Set CLOCK ADJUST time
On-Screen Display (OSD)
In USB/ Memory Card/DISC mode, short press to show Memory Card/USB/DISC information on the
display, long press one time to show the current playing track/ played time information, long press
twice to show the current playing track/ remainder time for play, long press again to clear the
information.
Driver Safety Function
Note: To watch video the parking wire should be connected to break signal.
Caution! The parking wire is connected with brake signal; for driving safety, the video programs
should only be viewed after the car is parked. Check and follow your local authority’s regulations
regarding watching video in a car.

Page - 12
Digital Tuner
Note: Memory Card /USB service availability varies with areas. Please understand if Memory Card
/USB service is not available in your area, the following service is not available, either.
Band selection
Press MODE button to select the RADIO mode.
Press the BAND button to select the desired band: FM1=> FM2 => FM3 => MW
STEREO/MONO
In FM mode, press SETREO/MONO button on remote control to select stereo or mono sound
reception.
LOC/DX
Press LOCAL button on remote control to select reception of local stations or DX for distance
stations.
Manual/ automatic tuning
zManual tuning: press the buttons on remote control or on the panel and hold for 2
seconds to enter the manual tuning mode. Press the / buttons on the panel or on the
Remote repeatedly to select a station downward or upward step by step.
zAutomatic tuning: press the buttons on the Remote or press
buttons on front panel, the automatic search will start. It will play when finds the station.
Preset station 1-6 play and setting
zPlay preset station: to play the preset station 1-6, you can press number key 1-6 on remote
control, you can also press SEL button on front panel
zPreset station setting: during manual turning or automatic tuning, press and hold the number
1-6 buttons on remote to store the preset station 1-6 or long press BAND button on front panel
and press +/- buttons and then press OK button to store.
Remark: You can store up to a total of 24 radio stations in the memory (18FM, 6MW).
AS (Auto Store) / PS (Preset Scan)
AS (Auto Store): In tuner mode, press the RPT/P.SCN button on the remote or AS/PS button on front
panel and hold for 2 seconds to store radio station’s with the best reception to the preset buttons
automatically.
PS (Preset Scan): In tuner mode, press this button to scan the preset memorized station, each
preset scan for 5 seconds. Press again to stop operation.
Memory Card/ USB Operations
USB Flash Memory
To play MP3/ MP4/ WMA files from a USB flash memory, insert a USB flash memory into the USB
port on the right side of the unit. The unit will start playing MP3/MP4/ WMA files on the USB flash
memory automatically. Or press the MODE button to select USB after pressing POWER button to
turn on the unit.

Page - 13
Memory CARD
To play MP3/ MP4/ WMA files on a Memory CARD, insert the card into the card slot (you should
press the OPEN button on the panel to flip down front panel and insert the card into card slot.) The
unit will start playing MP3/ MP4/ WMA files on the Memory card memory automatically. Or press the
MODE button to select Memory Card after pressing POWER Button to turn on the unit.
PAUSE/ PLAY
Press the PLAY/ PAUSE button to pause the playback. Press the button again to resume.
STOP
Press the STOP button on remote to stop playback. Press the PLAY/ PAUSE button to resume. If
the Memory card or USB is removed, the resume function will be cancelled.
Press the STOP button twice to stop the playback totally. Press the PLAY/ PAUSE button to start
playback from the beginning.
Selecting Tracks
If the MP3/ MP4/ WMA files are stored in the folders on the USB drive or Memory Card, the unit will
start by playing the first song in the first folder. After playing all the files sequentially in the first folder,
the unit will play all the files sequentially in the next folder. The unit will continue playing through all
of the folders on the USB drive or Memory card in this manner. Press the button to play the
previous track/chapter. Press the  to play the next track/chapter. Press the digital buttons (0-9)
to select the desired track/chapter.
On front face, press BAND button to move cursor right side for select track, press BAND button and
hold for 2 seconds to move cursor downward for select folders.
GOTO Function
Long press AUDIO/GOTO button on remote control to show GOTO menu, use 0-9 to input track/
time to go to directly.
Fast Forward and Backward
Press the /buttons and hold for two seconds to select the fast playing in backward or
forward in 2 times, press and hold for two seconds again for 4times, repeat this operation for 8 times
=> 20 times => play. Press the PLAY/PAUSE button to return to normal playback.
Note: During the Memory card or USB playback when Fast backward or forward gets to the
beginning of the playing another track, it resumes normal playback.
Repeat
Press the RPT button on remote control for REP 1 (repeat the current playing file) => REP DIR
(repeat current folder) => REP ALL (repeat all folders) => REP OFF.
Repeat A-B Function
1. Press A-B button on the remote at the starting point of the section you want to repeat (point A).
2. Press A-B button again at the ending point of the section you want to repeat (point B). Section
A-B repeating starts.
3. Press A-B button again to cancel the A-B repeat function.

Page - 14
Random
Press the RDM button on remote to play all song tracks in random order. Press and hold for two
seconds to play all album tracks in random order. Press again to cancel.
Note: This function is only for audio files.
Intro Playback
Press the INT button on remote to play the beginning of every track for 10 seconds in sequence.
Press again to cancel INT play.
Note: This function is only for audio files.
Programming the Playback
1. Press PROG button on the remote open program menu.
2. Use / / / buttons to select the program position and use digit 0-9 buttons to select the
desired track.
3. Press PLAY/ PAUSE button to program play, or move the cursor to select PLAY and press
ENTER button on remote or OK button on front panel to play.
4. Move the cursor to CLEAR on program menu, press ENTER button on remote or OK button on
front panel to delete the programmed list.
5. Press PROG again to cancel program play.
Return Function (For video files and pictures only)
During playback of a video file or picture, press STOP button to return to the file list menu.
Selecting Different Audio Modes (only for MP4 files)
Press AUDIO button on the remote repeatedly to select the audio language.
Changing the Subtitle Language (only for MP4 files)
Press SUB-T button on the remote to select the preferred language for sub-title.
ZOOM (only for MP4 files)
Press ZOOM button and hold for 2 seconds on remote to activate zoom function in the following
sequences: ZOOM 2 => ZOOM 3 =>ZOOM 4 => ZOOM 1/2=>ZOOM 1/3=>ZOOM 1/4=>ZOOM
OFF.
Rotate Picture (only for picture files)
In picture mode, press /buttons to rotate picture 90 degrees.
System Menu
In USB/ Memory Card mode, press SETUP button on remote to show system menu. Press / / / buttons to
set system data, press this button again to save input data and exit system menu.
.

Page - 15
Discs operations
Glossary
PBC (Play Back Control)
Play Back Control is a menu recorded on the disc with SVCD or VCD2.0 format. For the discs
contained PBC, it can playback interactive software with the menu displayed on TV. And if the disc
contains still images, it can playback high definition of still image.
Title
The title is the important part of DVD disc. The memory volume of the disc is rather big, that makes
possible to record several films on one disc. For example, if a disc contains three films, they may be
divided into Title 1, Title 2 and Title 3. You can easily use the functions to search.
Chapter
A title can be divided into several blocks, so that every block can be operated as a unit, the unit is
called chapter.
The chapter contains a unit at least.
Track
It is the biggest component of VCD. Generally, every song of Karaoke disc is a track.
Discs for playback
zThis unit can play:
DVD/SVCD/VCD/HDCD/MP3/MP4/WMA/CDDA/Picture-CD/JPEG/CD-R/-RW/DVD±R/±RW.
zThe following file types are supported:
Audio files: MP3 (*.mp3)
WMA (*.wma)
Video files: MP4 (*.avi, MPEG43.11/4.0/5.0/6.0 and XVID)
MPEG 2(*.vob)
MPEG 1(*.dat)
Picture file: JPEG (*.jpg)
zISO 9660 or ISO 9660 +Joliet format - Max. 30 characters
zMax. Track number is 448
zMax. nested directory is 8 levels
zThe max. album number is 99
zThe max. length of each track is 99 minutes 59 seconds
zSupported sampling frequency for MP3 disc: 8 KHz to 48 (44.1 KHz preferably) KHz
zSupported bit-rates of MP3 disc are: 32 - 320 kbps (128 kbps preferably).
zFollowing formats are NOT supported *.ACC, *.DLF, *.M3U, *.PLS, MP3 PRO, files with DRM.
zOpen session discs are NOT supported.

Page-16
Loading a disc
1. Turn the power on.
2. Press the Open button on the front panel to flip it down.
3. Insert the disc with the printed side facing upward into the slot. The panel will be closed
automatically. The DVD mode will be turned on automatically. The monitor will show the disc
content.
4. Press Open button on the panel and Eject button inner the panel to eject the disc.
If the disc is not removed for about 10 seconds after reject, the disc will reinserted automatically.
When disc in/out, put front panel at 0 degree to avoid distort the disc.
5 You may also choose the playing mode using the MODE button.
Playing/pausing
To ensure good system performance, wait until the unit finishes reading the disc information before
proceeding.
Press the PLAY/ PAUSE button to start/ pause the playback. In pause mode press it again to
resume the playback.
Stop
During playback press the STOP button on the RC. Playback will be stopped. Press the PLAY/
PAUSE button again to start playback from the position at which it was stopped. If the disc is
removed, the resume function is cancelled.
Press the STOP button twice to finally stop the playback. Press the PLAY/ PAUSE button to start
playback from the very beginning.
Playing the previous/ next track/ chapter
1. During playback press the button to start playing the previous track/chapter.
2. Press the to start playing the next track/chapter.
3. Press the digital buttons (1-9, 0) buttons to enter the desired track/chapter number.
Speed forward and backward
Long press the /buttons on the panel or press and hold for 2 seconds the or
on the RC to select the speed of fast playing in backward or forward direction: X2, X4, X8, X16, X32.
Press the PLAY/PAUSE button to return to normal playback.
Note: During the disc playback when Fast/ Reverse Playback gets to the beginning of the playing
another track, it resumes normal playback.
Repeat playback
Press the RPT/P.SCN button on the RC once or more times to repeat the playback:
- For VCD/CD: display appears Repeat Track => Repeat Disc => Off (Some discs do not support
this functions).
- For DVD: display appears Repeat Chapter => Repeat Title => Off
- For File disc: display appears File => Folder=> All => Off
Note: to choose FOLDER repeating and TITLE repeating press and hold RPT button.

Page - 17
Repeat A-B function
1. During playback, press A-B button on the remote control at the starting point of the section you
want to repeat (point A).
2. Press A-B button again at the ending point of the section you want to repeat (point B). Section
A-B repeating starts.
3. Press A-B button again to cancel the A-B repeat function.
Random playback (for CD/VCD/MP3 discs)
During disc playback, press the RDM button on the RC to start random playback of the disc. Press
again to cancel.
Intro playback (for CD/VCD discs)
You can play the beginning of every track for 10 seconds in sequence. Press the INT button on
remote control to start intro play of whole disc. Press again to cancel.
PBC (Playback Control) function (for VCD only)
If you insert a VCD with PBC, playback starts from the beginning of the 1st track automatically.
1. Long press PBC/STOP button to activate interactive menu on screen during playback.
2. If the menu consists of titles, you can select a desired one using the / buttons.
3. The VCD starts playing the selected title automatically or press PLAY/ PAUSE button to confirm
the selected track for playback.
Programming the playback
1. Press PROG button on the RC to enter
program list.
2. Use , , , buttons and digit buttons to
enter the number of the desired track to be
on selected position.
For DVD and File disc, select title and
chapter number.
For VCD and CD, select track number.
3. Press PLAY/ PAUSE button to play, or
move the cursor to select PLAY and press
ENTER to play.
4. If you want to delete the list, move the
cursor to CLEAR, press ENTER to delete
all the list set before.
5. Press PROG again to exit program play.
Selecting different audio modes
zFor DVD disc: press AUDIO on the RC repeatedly to select the audio language to listen (if the
disc supports multi-language mode).
zFor VCD disc: press AUDIO on the RC repeatedly to select the following modes:
L R STEREO (Channel left => Channel right => Stereo).

Page-18
Changing the subtitle language (for DVD only)
Press SUBTITLE button on the RC to select the preferred language for the disc menu. When the
selected language is recorded on the disc then this language will automatically be selected. If not,
the first language recorded on the disc is displayed.
Changing size
Press and hold for 2 seconds the A-B/ZOOM on the RC. The picture will be enlarged accordingly:
X2 => X3 =>X4 => X1/2=>X1/3=>X1/4X=>Normal.
Changing angle (for DVD only)
If DVD discs support multi-angle playback, press ANGLE on the RC button to playback images in
different camera angles. If discs doesn't support multi-angle playback, this function will not work. If
no operation within 1 second, angle description will disappear.
Menu navigation (for DVD only)
Press and hold MENU button on remote control to activate the disc menu list on the screen.
Choose the desired item by pressing cursor up/down/left/right buttons.
Press ENTER button on remote control or OK button on front panel to confirm the selected item and
start playing.
Note: Menu function is only available if the disc with this function.
MP3 overview
Notes on MP3:
zMP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard.
zThis product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs.
zThe unit can read MP3 files written in the format compliant with ISO 9660. However it does not
support the MP3 data written by the method of packet write.
zThe unit can not read an MP3 file that has a file extension other than “.mp3”.
zIf you play a non- MP3 file that has the “.mp3” extension, you may hear some noise.
zIn this manual, we refer to what are called “MP3 file” and “folder” in PC terminology as “track” and
“album”, respectively.
zMaximum number of directory level is 8, including the root directory. Maximum number of files
and folders per disc is 448.
zThe unit may not play tracks in the order of Track numbers.
zThe unit plays only the audio tracks if a disc contains both audio tracks and MP3 files.
zWhen playing a disc of 8 kbps or “VBR”, the elapsed playing time in the display window will not
be correct and also the intro play may not function properly. “VBR”: Variable Bit Rate.
Notes on creating your own CD-R or CD-RW containing MP3 files:
zTo enjoy high quality sound, we recommend converting to MP3 files with a sampling frequency of
44.1 kHz and a fixed bit rate o f 128 kbps.
zDO NOT store more than 448 MP3 files per disc.
zFor ISO 9660 - compliant format, the maximum allowable depth of nested folders is 8, including
the root directory (folder).
zWhen CD-R disc is used, playback is possible only for discs, which have been finalized.
zMake sure that when MP3 CD-R or CD-RW is burned that it is formatted as a data disc and NOT
as an audio disc.

Page - 19
zYou should not write non-MP3 files or unneeded folders along with MP3 files on the disc
otherwise it takes a long time until the unit starts to play MP3 files.
zWith some CD-R or CD-RW media, data may not be properly written depending on its
manufacturing quality. In this case, data may not be reproduced correctly. High quality CD-R or
CD-RW disc is recommended.
zUp to 16 characters are displayed for the name of an Album or a Track. ID3TAG version 1.x is
required.
zNote that the unit may not play Tracks in the order that you wrote them to the disc.
TV OPERATIONS [For PTID-3600T only] [[
1. Connect TV antenna, and then press MODE button to select TV mode.
2. In TV mode, press the MENU button once to enter TV menu setting.
3. Press the /buttons to select one of the setup pages: Auto program => Manual program.
4. Press OK button on front panel or ENTER button on remote control to enter the page.
5. Press the /buttons to select the setting.
6. Press OK button on front panel or ENTER button on remote control again to confirm, press
MENU to return to settings list.
TV MENU
Auto program (Auto seek mode)
System
Select this menu item to set TV video system: NTSC=>PAL, press OK button on front panel or
ENTER button on remote control to select.
Audio
Select this menu item to set the TV sound system: AUDIO1=> AUDIO2=> AUDIO3, press OK
button on front panel or ENTER button on remote control to select.
Search
Select this menu item is to start searching and storing stations automatically.
Manual program (manual seek mode)
Storage
Select this menu item to set the storage number.
System
Select this menu item to set TV video system: NTSC=>PAL, press OK button on front panel or
ENTER button on remote control to select.
Audio
Select this menu item to set the TV sound system: AUDIO1=> AUDIO2=> AUDIO3, press OK
button on front panel or ENTER button on remote control to select.
Channel
Select this menu item is to set your desired searching channel, press cursor left/right buttons on
remote control to select one.
Fine
Select this menu item is to fine TV picture and sound until it achieves the best quality, press cursor
left/right buttons on remote control to adjust.
Memory
Select memory on or off is to set whether memory the searched station or not, press press OK
button on front panel or ENTER button on remote control to select.
Notes:
TV cannot be displayed on the additional monitor.