PowerAcoustik PML-43HB User manual

Owner’s Manual
PML-43HB
EN
AV Center 1 DIN 4.3’’ Monitor
MP3/MP4
USB/SD
Built-in AM/FM Radio
Support Bluetooth
Support Phone Link

INTRODUCTION
Safety Warnning and Considerations
• Clean only with a dry cloth or other similar materials.
• Install your product in a dry location that does not interfere with your vehicle’s equipment.
• Do not block any ventilation openings when installing this product.
• Do not mount in the engine conpartment of your vehicle or any hot surfaces.
• Securely mount the product so that is does not come loose in the event of a collision or as a ruslt of
repeated vibrations that might occur during regular operation.
• Installation of the apparatus must be done with great care to prevent damage to your vehicle’s fuel lines,
power, and electrical wiring, hydraulic brake lines, and other systems. If possible, always vist your nearest
Power Acoustik dealer to perform the installation.
• Do not run any wireing outsied or underneath the vehicle. Keep all wires inside the car.
• Take the necessary precautions when making connections to the vehicle’s batter to avoid any potential
shock.
• Protect all system wires from sharp edges by carefully routing them, always use rubber grommets to
protect wiring and cables whenever installing them through metal opening.
• Secure all wiring using cable ties or wire clamps to protect them from moving parts and sharp edges.
Refer all servicing to qualied service professionals. Service is required when the head unit has been
damaged. Such as the power input terminals are damaged, liquid has been spilled, or objects have fallen
into the apparatus, the aparatus has been exposed to rain or moisture, does not operate normally, or has
beed dropped.
• Fused shall be replaced only with the correct type and fuse value, and only when the apparatus is
powered o.
• Exposure to high sound pressure levels may lead to permanent hearing loss. Takce every precaution to
protect your hearing.
• This product is designed specically for use with 12V negative-ground systems only. Using this product
in systems with positive ground and / or voltages other than 12V may damage the product and your
system.

2
INSTALLATION/ UN-INSTALLATION & ACCESSORIES
（1) Sleeve
（3) ISO Cable （A+B) （4) Harness
（6) User Manual （7) Remote Control
X2
ACCESSORIES Parking wire
2A
Parking brake lead Brown wire
Brake light
12 V
batter y
Car frame
12V
Car frame
Battery
Reve rse driving lightCar frame
Pink wire
Rear vie w vid eo came ra lead
P
R
N
D
L
2
Gearbox
（2) Release Key
X1
X1
X1
X1
（5) Microphone Cable
X1
Note: To watch video the parking wire should
be connected the brake signal.
• Clean only with a dry cloth or other similar materials.
• Install your product in a dry location that does not interfere with your vehicle’s equipment.
• Do not block any ventilation openings when installing this product.
• Do not mount in the engine conpartment of your vehicle or any hot surfaces.
• Securely mount the product so that is does not come loose in the event of a collision or as a ruslt of
repeated vibrations that might occur during regular operation.
• Installation of the apparatus must be done with great care to prevent damage to your vehicle’s fuel lines,
power, and electrical wiring, hydraulic brake lines, and other systems. If possible, always vist your nearest
Power Acoustik dealer to perform the installation.
• Do not run any wireing outsied or underneath the vehicle. Keep all wires inside the car.
• Take the necessary precautions when making connections to the vehicle’s batter to avoid any potential
shock.
• Protect all system wires from sharp edges by carefully routing them, always use rubber grommets to
protect wiring and cables whenever installing them through metal opening.
• Secure all wiring using cable ties or wire clamps to protect them from moving parts and sharp edges.
Refer all servicing to qualied service professionals. Service is required when the head unit has been
damaged. Such as the power input terminals are damaged, liquid has been spilled, or objects have fallen
into the apparatus, the aparatus has been exposed to rain or moisture, does not operate normally, or has
beed dropped.
• Fused shall be replaced only with the correct type and fuse value, and only when the apparatus is
powered o.
• Exposure to high sound pressure levels may lead to permanent hearing loss. Takce every precaution to
protect your hearing.
• This product is designed specically for use with 12V negative-ground systems only. Using this product
in systems with positive ground and / or voltages other than 12V may damage the product and your
system.
Package contains the following for installation
and operation of the unit.
Note: The parking wire is connected with brake
signal; for safety, the programs can be seen on the
headunits touch screen.
Connecting the reverse signal at taillight on
the car (12V+ Required for Signal).
After connecting, when you start up the
reverse gear, the unit will receive the picture
from car rear view camera.
Select the proper TAB
for fixing the sliding
metal housing.
Half Sleeve
Dashboard
Sliding body chassis
UNINSTALLATION
INSTALLATION
Insert the 2 release keys deeply into the
slot.
With the inserted keys to pull out the unit
halfway.
Pull the unit all the way with your hands,
being carefully not to drop it.
Owner’s Manual
PML-43HB
EN
AV Center
1DIN 4.3’’ Monitor
MP3/MP4
USB/SD
Built-inAM/FM Radio
SupportBluetooth
SupportPhone Link

3
Wiring:
Diagram：
Line-out（FL)
White
FL RL
V-OUT
R-CAM
ANT
MIC
FR RR
U6. Amplier Control
(Blue/White)
U5. Brake Detect (Brown)
U1. Ground (Black)
U2. Steer Wheel Control 2 (Green)
U3. Back Camera Control (Pink)
U4. Steer Wheel Control 1 (Gray)
Speaker Connection
White
Green
Grey
Purple
Line-out（RL)
White
Line-out（V-OUT)
Radio Antenna
External Microphone
Yellow
Line-out（Rear-Camera)
Line-out（RR)
Line-out（FR)
Red
Red
Yellow
We recommended using car speaker with
minimum 40 Watt potential.
Headunits potential power may result in
damaging your OE speakers at higher
volumes.
Use 4Ω -8Ω (Ohm impedance) speakers
only; using higher or lesser impedance may
damage the headunit.
Speaker cables and / or optional external
power amplifiers must always be about
30cm away from the antenna and / or
antenna extension parts.
Do not connect the speaker leads of the
power harness to battery; otherwise, the
unit will be seriously damaged.
Before connecting the speaker leads the
harness to the speakers, check the speaker
wiring in your car.
Connect the speakers according the following
diagram,incorrect connections will damage
the headunit or your vehicle’s speakers.
2
4
6
8
1
3
5
7
2
4
6
8
1
3
5
7
A
1
2
3
4
5
6
7
8
Color
NC
NC
NC
Yellow Battery +
Blue
ANT
Orange Illumination
Red ACC
Black Ground
Function B
1
2
3
4
5
6
7
8
Color
Purple(+)
Purple/Black(-)
Gray(+)
Gray/Black(-)
White(+)
White/Black(-)
Green(+)
Fuse: Max.15 Ampere
Voltage: 12V DC; Negative Ground
Green/Black(-)
Rear Right
Front Right
Front Left
Rear Left
Function
16 Pin Harness

PANNEL FUNCTION INTRODUCTION
4
1
IR Sensor of Remote
•IR remote control signal receiving window.
2
MENU Button
Vol button /Rotary Control/Selection Button
3
•Built-inmicrophone.
6Mic
7AUX jack
•[USB/SD Music] Press repeatedly to shift
track next for playback.
Press and hold to active fast forward
speeds for playback.
[Bluetooth Music] Press repeatedly to shift
track next for playback.
Long press to re-dial the latest call log.
•[USB/SD] Long press to enter folder
selection page.
Rotate the Vol-button to select the desired
file then press to playback.
Press the or to exchange select file
and folder(Music/Video/Photo) area.
•In operation, rotate to adjust the sound
output level.
•Long press to switch Off Mute or Unmute.
•In Pop-menu & setting menu, rotate to
selection.
•In operation, short press repeatedly to enter
selection Menu, then rotate to select desired
value:
Bass: -7~ +7
Treble:-7~ +7
Balance: L7~ R7
Fader: R7~ F7
EQ: BEAT>JAZZ>POP>ROCK>CLASSIC>OFF.
Loud: On / Off.
•In any mode, press MENU to pop-up menu
options, then Rotate the Vol-button to select
desired mode.
4
Button
•When the unit is turn off, short press to turn
on the unit.
Long press to turn off thr unit.
•In any mode, short press to select desired
mode.
•[Bluetooth ], short press to hang-up the
talking phone or reject the incoming call.
•If the unit or the connected unit fails to
operate properly, the unit returns to
factory settings when this button is
pressed.
•Insert an external device to this port in
order to have sound output of that
external device through the unit.
8Reset Button
10
11
Button
94.3 inch TFT Panel
5
Button
• [Radio] , press repeatedly to select Band:
FM1>FM2>FM3>AM1>AM2.
•
[USB/SD] , short press to select Music/
Video/Photo to playback.
•
[Bluetooth] , press answer the incoming
call or redial out.
•
[Radio] , press repeatedly to select desired
stored station.
•
[USB/SD] , press to select Play or Pause.
2
1
4
3
5
6
•[Radio] Press and hold to active manual
seek, then press to step upward. Press
previous button to step down.
Press to auto seek up.
11
10
12
14
13
15
8 97

PANNEL FUNCTION INTRODUCTION & REMOTE CONTROL
REMOTE CONTROL
5
•[Radio] Press to select preset 1 radio
station for broadcasting.
•[USB/SD/BT Music]Press to Play or Pause.
•[Radio] Short press to Prescan search,
each scanned station will be play for 3 sec.
Long press to Auto Search.
•[Video] Press to transfer the video out, at
same time , the unit display will be black.-
Press again, stop video out, the unit
display will turn on.
•[USB/SD ile page] Press to access to right
file selection area.
Selection Button
•In operation, short press repeatedly to enter
selection Menu, then press or to
select desired value:
Bass: -7~ +7
Treble:-7~ +7
Balance: L7~ R7
Fader: R7~ F7
EQ: BEAT>JAZZ>POP>ROCK>CLASSIC>OFF.
Loud: On / Off.
12 TF Card
•Insert TF Card for playback.
button
1
Button
•Press to Power on / Power off.
2
Button
• [Radio] , press repeatedly to select Band:
FM1>FM2>FM3>AM1>AM2.
•
[Bluetooth] , press answer the incoming
call or redial out.
•[Radio] Press and hold to active manual
seek, then press to step upward. Press
previous button to step down.
Press to auto seek up.
•[USB/SD Music] Press repeatedly to shift
track previous for playback.
Press and hold to active fast rewind for
playback.
[Bluetooth Music] Press repeatedly to shift
track Previous for playback.
Long press to dis-connect the phone, press
again to re-connect.
•[Radio] Press and hold to active manual
seek, then press to step upward. Press
previous button to step down.
Press to auto seek up.
•[USB/SD Music] Press repeatedly to shift
track previous for playback.
Press and hold to active fast rewind for
playback.
[Bluetooth Music] Press repeatedly to shift
track Previous for playback.
Long press to dis-connect the phone, press
again to re-connect.
14
15
3
4
EQ/Loud Button
•Short press to select desired preset EQs
EQ: BEAT>JAZZ>POP>ROCK>CLASSIC>OFF.
•Long press to select Loud is On/Off.
5
1/ Button
6
•Connect USB for digital playback.
•Connect your moblie phone for charging.
13 USB port
1
2
5
3
4
9
8
7
6
10
11
12
16
13
14
15
18
17
•[Radio] Press to select preset 2 radio
station for broadcasting.
•[USB/SD Music]Press to active INTRO or
not.
2/ INT Button
7

MANUAL SEEK:
Long press or butto to active
Manual Seek, then press repeatedly to
step up or down.
SEEK:
Long press or butto to Seek up
or Seek down.
REMOTE CONTROL FUNCTIONS APPLICATION
6
PML-43HB is a 1-DIN car audio with following
functions:
Radio, Bluetooth, USB, SD, AUX,Camera,-
PhoneLink.
Menu Selection
Pop-Menu
•In any mode, press MENU to Pop-up menu
options, then Rotate the Vol-button to select
desired mode: Radio, USB, SD, Bluetooth,AUX
in, RCAM, PhoneLink.
Radio Interface
10
Button
•In any mode, short press to select desired
mode.
•[Bluetooth], short press to hang-up the
talking phone or reject the incoming call.
•[USB/SD Music] Press repeatedly to shift
track next for playback.
Press and hold to active fast forward
speeds for playback.
[Bluetooth Music] Press repeatedly to shift
track next for playback.
Long press to re-dial the latest call log.
•[Radio] Press and hold to active manual
seek, then press to step upward. Press
previous button to step down.
Press to auto seek up.
Preset station.
1
Display the headunit information: BT icon,
Volume, USB icon, SD icon,time...
2
When the radio function is activited, will
display the icon: ST, LOC..
3
4
Display current playback station’s infor-
mation: Band, Frequency...
5
1
5
2
•[Radio] Press to select preset 4 radio
station for broadcasting.
•[USB/SD Music]Press to active Random or
not.
4/ RDM Button
8
•[Radio] Press to select preset 3 radio
station for broadcasting.
•[USB/SD/BT Music]Press to active Repeat
or not.
3/ RPT Button
17
•[Radio] Press to select preset 5 radio
station for broadcasting.
•[Radio] Short press to Prescan search,
each scanned station will be play for 3 sec.
Long press to Auto Search.
5 Button
9
•Press to Mute or Unmute.
Mute Button
11
APS Button
12
•Press to increase the Volume value.
VOL+ Button
13
•Press to decrease the Volume value.
VOL- Button
16
•Press to display the informations.
•[Radio] Press to select preset 6 radio
station for broadcasting.
6 Button
18
DISP Button
15
14
4
3
SEEK

7
FUNCTIONS APPLICATION
Music (USB/SD) Interface
Bluetooth Pairing
No Paired
Bluetooth Music
Folder Interface
Note: How to store the station.
1. Search for the desired frequency.
2. Press button to active the preset
station area.
3. Rotate the Vol-button to select the
desired preset station.
4. Press the Vol-button to store the station.
Note: How to Select the le.
•[USB/SD] Long press to enter folder
selection page.
Rotate the Vol-button to select the Music/
Video/Photo, then area will display all the
folders and files.
Press the to access the area, then
rotate the Vol-button to select the desire file,
press Vol-button to confirm to start play.
Press the to back the area.
Turn On the Bluetooth of the Mobile phone/
Bluetooth device, you can see the
Power Acoustik. Select the Power Acoustik
for pairing and connection.
Display the headunit information: BT icon,
Volume, USB icon, SD icon,time...
Current playback track sequency number.
1
2
3
4
Current playback track ID3 information.
1
2
Current playback track ID3 information.
Selection area: Music / Movie / Photo.
1
2Selection area: Select desired file to
playback.
Play /Pause status indicator.
Play /Pause status indicator.
Play time indicator.
5
Indicate INTRO/ REPEAT / RANDOM icon.
6
21
4 5 6
3
1
2

8
Setting Menu
Language
FUNCTIONS APPLICATION
Bluetooth Phone
AUX IN
The Audio source with RCA cable can
through the source unit to play the Audio.
Rotate the Vol-button to select the desired
language, press again to confirm.
Rotate the Vol-button to select 12H or 24H
time format.
Rotate the Vol-button to select PAL or NTSC
video format.
Press Vol-button to select the Hour / Minute,-
press again to active adjustment, then rotate
Vol-Button to adust time.
1Show Dials & Receives Calls Logs.
1
Radio Area
Time
Press Vol-button to select the Month /
date/Year,press again to active adjustment,
then rotate Vol-Button to adust date.
Date
Time Mode
Rotate the Vol-button to select the desired
Radio Area, press again to confirm.
America
PAL/NTSC

9
FUNCTIONS APPLICATION
Rear view camera
To use a rear view camera, the REVERSE
lead connection is required.
For connecting a rear view camera.
The rear view screen is displayed when you
shift the gear to the reverse (R) position.
Displaying the picture from the
rear view camera
Rear Camera
Rotate the Vol-button to select Video
warning is On or Off.
Note: When driving, watching video is forbid-
den.
Rotate the Vol-button to LED Color: AUTO,
WHITE,PURPLE,CYAN,YELLOW,
RED,BLUE,GREEN
LED Color
Make the cursor correspond to the function
to be adjused, then press the steering wheel
button to hightlight the button icon of the
device. After learning in order, press Exit to
complete the operation.
Steering wheel controls
Video warning
Press the Vol-button, will display Pop-menu:
Factory default. The rotate to select “Yes” or
“No”, press again to confirm.
Factory Default
Version
MP5:
MCU: