PowerAcoustik HD-14KIT User manual

Owner’s Manual
HD-14KIT
EN
WATERPROOF
FACEPLAT E
IPx5 4-Channel
Amplifier

Safety Definitions
Safety First
Safety First
Pre-Riding
Check list 3
Care and cleaning 3
Screen 3
Appearance 3
Accessories 4
Installation 5
Trouble Shooting 20
Warranty 23
FCC Notes 22
Specication 21
Headunit Control 12
Operation
Main menu 13
Setting 13
Apple CarPlay/Android Auto 15
Radio operation 16
USB operation 17
Bluetooth Music 17
Bluetooth Phone 18
Contents
Statements in this manual preceded by following
words are of special significance:
WARNING
WARNING
WARNING
Note
Pay attention while riding, keeping your eyes and
clear mind on the road. Some features are locked out
to prevent distraction, limited in capability while the
Motorcycle is in motion. Even a part is available, do
not allow it to distract you from operating your
Motorcycle safely.
For safety, program the system when stopped.
Perform system setup and get familiar with the
controls and features of the infotainment system
before operating the Motorcycle on the road.
This system cannot warn about the safety of an area,
bad road conditions, and availability of emergency
services.
Use this radio only in locations where it is safe to do.
Do not select a volume level that blocks out
trac noise or interrupts the concentration
necessary for the safe operation of the Motor-
cycle. Distractions or a volume level that
blocks our trac noise could cause loss of
control resulting in death or severe injury.
Set volume levels and other controls on
audio and electronic devices before riding.
Distractions can lead to loss of control,
resulting in death or serious injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
22

Pre-RIDING
CARE AND CLEANING
Check list
Appearance
Front
Side
Back
Screen :
Configure the system with your personal
preferences before riding to use features and
minimize distractions while on the road
entirely.
1. Set brightness, background.
2. Configure presets.
3. Adjust audio settings like EQ, volume, fade,
balance etc. before ridding.
4. Pair, connect and set up phone features
through Bluetooth.
5. Connect USB devices for Apple CarPlay® or
Android Auto®.
6. Selectstation or media
Use only HD-14KIT recommended products
and methods to keep the radio, speakers, and
other audio system components clean and in
good condition.
Do not use any abrasives, polishes, or rubbing
compoundsto clean the screen or other
components. Do not use any ammonia-based
cleaners on the net.
The use of other products or methods may
cause damage to components.
Do not use any chemical cleaners or
chemical-containing wipes or cloths.
These can cause damage to the screen
surface.
Gently clean the display glasssurface with a
clean, dry microfiber cloth. Before cleaning, it
is suggested to remove any visible dust, dirt,
sand particles with a gentle compressed
airstream.
HD-14KIT
3

Harness Included!
Installation Trim Ring: Installation Bracket(Left/Right):
Installation Bracket
Screws TM5*6 (8pcs):
Installation Trim Ring
Screws TA4*10 (4pcs) :
External Microphone:
Manual:
48 Pin to Motorcycle Connector to Headunit(ISO A+B)
Accessories
Owner’s Manual
HD-14KIT
EN
WATERPROOF
FACEPLATE
IPx5
4

Installation
REMOVAL OF ORIGINAL HEAD UNIT
Street Glide
To prevent accidental vehicle start-up, which could cause death or serious injury, remove main
fuse before proceeding.
4. Remove upper support bracket. Removal of the
upper support bracket requires removing 11 screws:
4.1) remove four 5/32 allen screws
attaching the bracket to each speaker
enclosure (1)
4.2) remove two T25 screws attaching the
bracket to the inner fairing adjacent to
the gauge cluster (2)
4.3) remove four T25 screws attaching the
bracket to the head unit chassis (3)
4.4) remove one T25 crew attaching the
bracket to the media compartment (4)
3
1
4
2
1. Remove three outer fairing bolts using a T27 Torx screw
driver. The three outer fairing bolts are located below the
windshield. Remove the windshield, store it and the screws
removed in a safe place for re-installation later.
TIP: Reinstalling the center screw after removing the
windshield will prevent the outer fairing from falling during
the next step. A few turned by hand will be sucient.
2. Remove four inner fairing bolts using a T27 Torx screw driver. The four inner fairing bolts are locate
adjacent to each turn indicator mounting bracket and below/adjacent to each speaker. Store these
screws in a safe place for re-installation later.
3. While straddling the front wheel fender, grasp the outer fairing, remove the center outer fairing
bolt from the previous step, then gently pull the fairing apart from the bike. With the fairing slightly
pulled away from the bike, disconnect wire harness for the headlamp and any other accessories. Lay
the fairing on a protected flat surface to prevent damage.
5

Installation
5. Disconnect electrical connections to the head unit.
1234 5
5.1) Remove the main wire harness connector (1). To remove the main wire harness, depress the latch lock
with a small flathead screwdriver and swivel the latch aside. Pull the wire harness connector to remove
from the socket.
5.2) Remove the USB cable connector (2). To remove the USB cable connector, depress the locking tab
with a small flathead screwdriver. While depressing the locking tab, pull the USB cable to release it from
the socket.
5.3) Remove the radio antenna cable connector (3). To remove the radio antenna cable connector,
depress the locking tab wiht a small flathead screwdriver. While depressing the locking tab, pull the
antenna cable to release it from the socket.
5.4) Remove the GPS antenna cable connector (4). To remove the GPS antenna cable connector, depress
the locking tab wiht a small flathead screwdriver. While depressing the locking tab, pull the antenna
cable to release it from the socket.
6. Remove four head unit mounting screws using a 3/16” hex driver. Two screws are located at each
side of the headunit chassis. Store these screws in a safe place for re-installation later. Pull the headunit
assembly up and forward to remove.
5.5) Remove SiriusXM antenna cable connector, if equipped (5). To remove the Sirius XM antenna cable
connector, depress the locking tab with a small flathead screwdriver. While depressing the locking tab,
pull the Sirius XM antenna cable to release if from the socket.
6

Installation
REMOVAL OF ORIGINAL HEAD UNIT
Road Glide
To prevent accidental vehicle start-up, which could cause death or serious injury, remove
main fuse before proceeding.
2
1. Detach each turn signal / indicator light by
removing the adjacent allen socket screw,
using a 3/16” allen head driver. Store these
screws in a safe place for re-installation later.
2. Remove four inner fairing bolts using a T25 Torx
driver. Two inner fairing bolts are located below each
glove box, adjacent to each wind deflector. Store
these screws in a safe place for installation later.
3. Remove four windshield bolts using a 1/8”
allen driver or Philips screw driver and remove
the windshield. Also remove factory vent by
pulling straight up on the vent. The vent comes
snapped in place. Store the screws in a safe
place for installation later.
4. After removing the vent, locate and unplug the 3-pin
wire harness for the left and right side turn signal
indicator. These harness’ are adjacent to each side of
the head unit.
5. Remove an additional inner fairing bolt with a T27 Torx or 5/32”
allen driver, one behind each speaker grill. Remove the speaker
grill by wedging a plastic/nylon pry tool between the inner fairing
and grill edge, popping it outward. Once these bolts are removed,
the outer fairing will be detached from the inner fairing. Store
these screws in a safe place for installation later.
6. While straddling the front wheel fender, grasp the outer
fairing. Gently pull the fairing apart from the bike. With the
fairing slightly pulled away from the bike, disconnect wire
harness for the headlamp or any other accessories. Lay the
fairing on a protected flat surface to prevent damage.
7. Remove two upper support bracket screws using a 3/16”
allen driver. Store the bracket and screws in a safe place for
re-installation later.
7

Installation
8
8.1) Remove the main wire harness connector (1). To remove the main wire harness,depress the latch
locking tab wiht a small flathead screwdriver. While depressing the locking tab, pull the USB cable to
release it from socket.
8.2) Remove the USB cable connector (2). To remove the USB cable connector, depress the locking tab
wiht a small flathead screwdriver. While depressing the locking tab, pull the USB cable to release it from
socket.
8.3) Remove the radio antenna cable connector (3). To remove the radio antenna cable connector,
depress the locking tab wiht a small flathead screwdriver. While depressing the locking tab, pull the
antenna cable to release it from the socket.
8.4) Remove the GPS antenna cable connector (4). To remove the GPS antenna cable connector, depress
the locking tab wiht a small flathead screwdriver. While depressing the locking tab, pull the antenna cable
to release it from the socket.
9. Remove four head unit mounting screws using a 3/16” hex driver. Two screws are located at each
side of the headunit chassis. Store these screws in a safe place for re-installation later. Pull the headunit
assembly up and forward to remove.
8.5) Remove SiriusXM antenna cable connector, if equipped (5). To remove the Sirius XM antenna cable
connector, depress the locking tab with a small flathead screwdriver. While depressing the locking tab,
pull the Sirius XM antenna cable to release if from the socket.
8. Disconnect electrical connections to the head unit.
1234 5
8

Installation
1. Install trim ring and left /right bracket into the location of the HD-14KIT head unit.
Note: Please use the screws in package.
Install trim ring use TA 4X10mm screws.
Install bracket use TM 5x6mm screws.
Trim Ring
Left /Right Bracket
2. Install HD-14KIT into the location of the OEM head
unit. Secure the chassis to the OEM mounting
location with the four bolts removed during the last
step of REMOVAL OF ORIGINAL HEAD UNIT section
using a 3/16” allen driver.
3. Connect the USB and radio antenna cables disconnected during removal of the OEM headunit to the matching
sockets on the back of HD-14KIT. If either are difficulet to connect, verify the oriention of the connector(s) is
correct. If any aftermarket audio amplifiers will be used in the audio system, take a moment to connect the RCA
cables to the corresponding audio outputs. Although not required, if the Bluetooth calling microphone will be
used, secure it to the desired installation location, then route its cable to the corresponding input on the back of
HD-14KIT.
INSTALLATION OF HD-14KIT HEAD UNIT
To prevent accidental vehicle start-up, which could cause death or serious injury,
remove main fuse before proceeding.
USB Connector (USB Storage
/Apple CarPlay/Android Auto)
OEM Radio Antenna Connector
3. 5mm Connection for Included
Bluetooth Calling Microphone
RCA Low-Level Subwoofer Channel Output
For Optional Subwoofer Amplier (RCA not incl.)
RCA Low-Level Front Channel Output
for Optional Speaker Amplier (RCA not incl.)
RCA Low-Level Rear Channel Output
for Optional Speaker Amplier (RCA not incl.)
A
B
9

Installation
4. Insert and lock the male ISO head unit wire harness connector to the female socket of the included wire harness
for HD-14KIT. Then, insert and lock the male connector of the HD-14KIT wire harness into the corresponding
female socket on the back of HD-14KIT.
5. If an alternative handlebar integration module other than Scosche is available, skip this step and proceed to step
6. If included, connect the Scosche handlebar integration module to the corresponding 12-pin and 14-pin
connectors on the wire harness of HD-14KIT.
A
B
A
B
2 4 6 8
1 3 5 7
2 4 6 8
1 3 5 7
A
1
2
3
4
5
6
7
8
Color
Yellow
Black/White
SWC-GND
Gray/White
SWC2
Green/White
SWC1
Battery +
Blue
ANT
Orange Illumination
Red
ACC
Black Ground
Function B
1
2
3
4
5
6
7
8
Color
Purple(+)
Purple/Black(-)
Gray(+)
Gray/Black(-)
White(+)
White/Black(-)
Green(+)
Fuse: Max.15 Ampere
Voltage: 12V DC; Negative Ground
Green/Black(-)
Rear Right
Front Right
Front Left
Rear Left
Function
ISO Connector
HD-14KIT wire harness OEM wire harness
SCOSCHE
Gray/Black (FR-)
Gray (FR+)
White/Black (FL-)
Purple/Black (RR-)
Purple/White (CAN-)
Green/White (CAN+)
Green/Black (RL-)
Purple(RR+)
Green(RL+)
White(FL+)
Black (Ground)
Black (Ground)
Yellow (Black)
Yellow (Black)
10