Powerley Energy Bridge User manual

Powerley Energy Bridge Setup Guide 1
Powerley Energy Bridge
Setup Guide

Powerley Energy Bridge Setup Guide 2
POWERLEY Brand Book and Style Guide
Introduction
Welcome to your new Energy Bridge! This
guide will help you set it up on your home
network via WiFi or wired internet connection.
If you have questions during the installation
process that are unanswered by this guide, you
can contact Powerley’s technical support via
email or phone:
[e-mail]
248-537-9440
Introduction 2
Energy Bridge Setup 3
Launch setup within [app name] app 3
Connect Energy Bridge to power and Internet 3
Locate Energy Bridge with your mobile device 3
Connect to Account 3
Connect Energy Bridge to Internet via WiFi 3
Bind Energy Bridge to Smart Meter 3
You did it! 4
Regulatory Information 5

Powerley Energy Bridge Setup Guide 3
Energy Bridge Setup
1. Launch setup within [app name] app
Launch the [app name] app on your mobile device and navigate
to the My Devices from the main menu. Tap on the green "Begin
Energy Bridge Setup" button and follow the remaining steps here
along with the app instructions.
4. Connect to Account
Now that your Energy Bridge has been located, you are now ready
to connect to your account. Tap "Connect to Account" on the
app to continue. When the app notifies you that your account is
successfully connected, tap "Next Step."
5. Connect Energy Bridge to Internet via WiFi
If your Energy Bridge is more than 25ft away from your Smart Meter
with a wired connection, move it within 5-25ft to increase signal
reliability to your meter. Plug it into a power outlet and tap "Set Up
WiFi" on the app. Select your WiFi network and connect to it. Once
connected, tap "OK, I Moved it" on the app to continue.
6. Bind Energy Bridge to Smart Meter
To securely connect your Energy Bridge to your Smart Meter, tap
"Request Bind." Wait [time period] and tap "Check Bind Status" in
the app. If bind was successful, you're all done!
2. Connect Energy Bridge to power and Internet
Plug your Energy Bridge into a power outlet using provided cable. If
your router is within 25ft of your home's Smart Meter, continue with
a wired connection by plugging the Energy Bridge into an available
port on your WiFi router with second cable and skip steps #–#.
3. Locate Energy Bridge with your mobile device
Before locating, be sure that your mobile device is connected to the
same WiFi network as your Energy Bridge. Tap the "Start Locating"
button on the app to locate Energy Bridge. When the app notifies
you it's been successfully located, tap "Next Step."
NOTE If router is more than 25ft away from Smart Meter, do not
plug Energy Bridge into the router; skip to next step.
NOTE If the Energy Bridge is unable to bind, try connecting the
Energy Bridge via WiFi if you have not already done so, move it
closer to you Smart Meter, and tap "Request Bind Again." If the
issue persists, contact support directly from within the app.

Powerley Energy Bridge Setup Guide 4
You did it!
You are now connected to the fastest
real-time management platform and are
ready to launch real-time usage and control
smart devices in your home.
If you ran into any issues during this setup
process or have further questions, you can
contact Powerley’s technical support via
email or phone:
[e-mail]
248-537-9440
www.powerley.com

Powerley Energy Bridge Setup Guide 5
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
FCC Part 15.21 Statement
Changes or modifications made to this equipment not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
FCC Part 15.105 Compliance Statement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. End users must follow the
specific operating instructions for satisfying RF exposure compliance.
This transmitter must be at least 20 cm from the user and must not
be co-located or operating in conjunction with any other antenna or
transmitter.
NOTE
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) regulatory information
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d´Industrie Canada
applicables aux appareils radio exempts de licence.
L´exploitation est autorisée aux deux conditions suivantes : (1)
l´appareil ne doit pas produire de brouillage, et (2) l´utilisateur de
l´appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d´en compromettre le fonctionnement
Regulatory Information