Banner SureCross DX80 User manual

Printed in USA 11/07 P/N 134421
SureCross™ DX80
DX80 Wireless I/O Network System Web Configurator
Reference Guide

Banner Engineering Corp.
9714 Tenth Ave. No.
Minneapolis, MN USA 55441
Phone: [phone]
www.bannerengineering.com
Email: [email protected]
P/N 134421
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for
one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its
manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of Banner
products. This warranty is in lieu of any other warranty either expressed or implied.
CAUTION . . .
Make no modifications
to this product.
Any modifications to this product not
expressly approved by Banner Engineering
could void the user’s authority to operate
the product. Contact the Factory for more
information.
All specifications published in this document are subject to change. Banner reserves the right to modify the specifications of products, prior to their
order, without notice. Banner Engineering reserves the right to update or change documentation at any time. For the most recent version of any
documentation, please refer to our website: www.bannerengineering.com. © 2007 Banner Engineering Corp. All rights reserved.
Always use lightning arrestors/surge protection with all remote antenna systems to avoid
invalidating the Banner Engineering Corp. warranty. No surge protector can absorb all lightning
strikes. Do not touch the DX80 or any equipment connected to the DX80 during a thunderstorm.
The manufacturer does not take
responsibility for the violation of any
warning listed in this document.

P/N 134421 3
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
Table of Contents
Login..........................................................................................................................................................................7
Changing the Host IP Address ....................................................................................................................................... 7
Changing the Device IP Address.................................................................................................................................... 8
Selecting a Host Communication Protocol ..................................................................................................................... 8
Get ALL Command ......................................................................................................................................................... 9
Change, Refresh, Send, and Update Commands.......................................................................................................... 9
Saving Changes to the XML File.................................................................................................................................... 9
RF Devices Tab ......................................................................................................................................................11
Select Models......................................................................................................................................................11
Configure Points..................................................................................................................................................13
Expanded Configure Points.................................................................................................................................16
I/O Linking ...........................................................................................................................................................19
Scaling.................................................................................................................................................................20
Remote I/O ..........................................................................................................................................................21
DX80 is Modbus/TCP Client/Server (default) ............................................................................................................... 22
DX80 Gateway is Modbus RTU Master........................................................................................................................ 23
DX80 is Modbus RTU Slave......................................................................................................................................... 25
Network Tab............................................................................................................................................................27
Modbus Data Submenu.......................................................................................................................................27
RTU Registers .............................................................................................................................................................. 27
RTU Error Codes .......................................................................................................................................................... 28
TCP Error Codes .......................................................................................................................................................... 29
TCP Registers............................................................................................................................................................... 29
Modbus RTU Setup Submenu ............................................................................................................................30
RTU Read Map............................................................................................................................................................. 30
Expanded RTU Read Map............................................................................................................................................ 32
RTU Write Map ............................................................................................................................................................. 33
Expanded RTU Write Map............................................................................................................................................ 34
Modbus TCP Setup Submenu.............................................................................................................................35
Devices ......................................................................................................................................................................... 35
Client Read Map ........................................................................................................................................................... 36
Expanded Client Read Map.......................................................................................................................................... 37
Client Write Map ........................................................................................................................................................... 38
Expanded Client Write Map.......................................................................................................................................... 39
Server Map ................................................................................................................................................................... 40
System Tab .............................................................................................................................................................43
Data Submenu.....................................................................................................................................................43
Local Registers ............................................................................................................................................................. 43
Thresholds .................................................................................................................................................................... 44
Trend Data .................................................................................................................................................................... 44
Action Rules Submenu........................................................................................................................................45
Thresholds .................................................................................................................................................................... 45
Expanded Thresholds ................................................................................................................................................... 45
Trending........................................................................................................................................................................ 47
Cascade........................................................................................................................................................................ 48
Calculate ....................................................................................................................................................................... 48
Constants...................................................................................................................................................................... 49
Setup Submenu...................................................................................................................................................50
Config File..................................................................................................................................................................... 50
Network......................................................................................................................................................................... 51
User............................................................................................................................................................................... 53
Time and Date .............................................................................................................................................................. 55

4P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
Advanced Tab .........................................................................................................................................................57
Scheduler Submenu............................................................................................................................................57
Weekly Schedule .......................................................................................................................................................... 57
On Demand................................................................................................................................................................... 59
Holidays ........................................................................................................................................................................ 60
Data Logger Submenu ........................................................................................................................................61
Log Files ....................................................................................................................................................................... 61
Data Points ................................................................................................................................................................... 63
Events Logged .............................................................................................................................................................. 64
File List.......................................................................................................................................................................... 64
E-mail Alerts Submenu........................................................................................................................................65
Recipients ..................................................................................................................................................................... 65
Events ........................................................................................................................................................................... 67
E-mail Server ................................................................................................................................................................ 68
Script BASIC Submenu .......................................................................................................................................69
Program File ................................................................................................................................................................. 69
View/Edit ....................................................................................................................................................................... 70
Virtual Terminal............................................................................................................................................................. 71
Basic Configuration .................................................................................................................................................73
Devices................................................................................................................................................................73
I/O Configuration .................................................................................................................................................74
I/O Linking ...........................................................................................................................................................75
Link Timeout........................................................................................................................................................76
System Network Settings ....................................................................................................................................77
Advanced Configuration..........................................................................................................................................78
Thresholds...........................................................................................................................................................78
Data and Event Logging......................................................................................................................................79
Log Files ....................................................................................................................................................................... 79
Scheduling...........................................................................................................................................................81
Trending Data......................................................................................................................................................82
Scaling.................................................................................................................................................................82
Floating Point Registers................................................................................................................................................ 83
Appendix A - Troubleshooting.................................................................................................................................85
Restoring Factory Default Settings............................................................................................................................... 85
Appendix B - Reference Information.......................................................................................................................87
Error Codes .........................................................................................................................................................87
Data Logger Error Codes.............................................................................................................................................. 87
File System Error Codes............................................................................................................................................... 87
E-mail Error Codes ....................................................................................................................................................... 89
Floating Point Registers ......................................................................................................................................90
Connection Status ..............................................................................................................................................90
RTU and TCP Error Codes .................................................................................................................................91
Network Connection Errors .................................................................................................................................91
Index........................................................................................................................................................................93

P/N 134421 5
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
Web Configurator
The SureCross™ DX80 Gateway Pro and DX83 Ethernet Bridge devices use an XML file to
configure the network. To access the XML file, use any web browser and enter the device’s IP
address into the browser’s address window:
http://192.168.0.1
The web configuration pages are arranged with a hierarchy of index tabs. The upper row of tabs
is the top of the hierarchy and selects a broad topic. Top level tabs open related tabs on the next
levels down. The middle tab selects a sub-topic, and the bottom tabs select individual pages
within the sub-topic. The bottom of each page includes a Quick Help section listing usage tips or
instructions specific to that page.
Before changing parameters...
...in the Web Configurator, go to the
RF Devices > Select Models page.
Check the Get ALL box for all network
devices and click the Update button.
This retrieves all settings from the
devices and loads them in the Web
Configurator.
Save these settings by going to System
> Setup > Config File and clicking the
Save or Save As button to ensure
the configuration file contains the
most recent information stored on the
SureCross™ devices.
Tip
SureCross™ DX80 Web Configurator
Instruction Manual
Introduction
The XML file on any Ethernet Bridge or Gateway Pro does not necessarily contain the settings for
a specific wireless network. In many cases, the XML file saved in the Ethernet Bridge or Gateway
Pro is a default configuration file. Attaching the Ethernet Bridge or Gateway Pro to the radio network
does not automatically transfer network or device settings to the Ethernet Bridge or to the XML file.
When viewing real-time data returned to the browser by the connected device, the browser displays
the data received when the page displayed. At this time, update data by clicking the Refresh button
or the web browser’s Reload or Refresh button. Each time a page update is requested, new real-
time data displays.
For more information on specific SureCross components, please refer to the data sheets for the
SureCross devices:
• Gateways
• Line-Powered Nodes
• FlexPower™ Nodes
Additional reference guides are available at www.bannerengineering.com/surecross on a variety of
topics, including:
Literature Number Topic
132113 A guide to antenna basics
132114 A guide to using Modbus with the SureCross products
133601 Samples of SureCross network configurations
133602 Running the Site Survey and interpreting the results
136689 A guide to SureCross network basics
136214 A guide to connecting sensors to DX80 devices

6P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
Introduction
Notes

P/N 134421 7
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
Login
Login
The SureCross™ DX80 Gateway Pro and DX83 Ethernet Bridge devices use an XML file to
configure the network. To access the XML file, use any web browser set up for a direct connection
to the Internet. If problems occur while connecting, verify the browser is not set to use a proxy
server.
When connecting to the Ethernet Bridge or Gateway Pro directly from a host computer, a crossover
Ethernet cable is required; when connecting through a switch or Ethernet hub, use a standard
Ethernet cable.
Changing the Host IP Address
The factory default IP address for the DX83 Ethernet Bridge and DX80 Gateway Pro devices is:
192.168.0.1.
To change the device’s default IP address, first set up the host PC with an IP address different from
the Ethernet Bridge or Gateway Pro IP addresses. (Please refer to Banner document 133116 for
detailed instructions on setting up the host computer’s network IP address.) For example, change
the PC host IP address to:
192.168.0.2.
After changing the host’s IP address, open a web browser and log into the Ethernet Bridge or
Gateway Pro by typing the IP address in the browser location window:
http://192.168.0.1
Enter the following as the user name and password.
User name: system
Password: admin
After entering the IP address, the home web page for the Ethernet Bridge or Gateway Pro displays.
To log in, click on any tab at the top of the page. To log out, close the browser.

8P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
Login
Selecting a Host Communication Protocol
By default the Ethernet Bridge and Gateway Pro systems communicate with a host using Modbus/
TCP. After establishing the IP address of the Ethernet Bridge and host, the system is set up to use
Modbus/TCP.
The system can also use EtherNet/IP™. To change the system to EtherNet/IP, follow the previous
instructions regarding the device and host IP address, and then:
1. Log in using the following user name and password:
User name: root
Password: sxi
2. At the bottom of the System > Setup > Network page is a checkbox to enable EtherNet/
IP. Only select this box if the Gateway Pro system is running on an EtherNet/IP network.
This change cannot be enabled from a login other than the “root” login.
3. After selecting the EtherNet/IP Enabled checkbox, click the Set Ports button to save
any changes made to the HTTP Port, Modbus Server Port, Telnet Port, or EtherNet/IP
Enabled settings.
Changing the Device IP Address
Once logged into the system, use the page tabs at the top of the page to select the path: System >
Setup > Network. To change the Ethernet Bridge or Gateway Pro’s IP address:
Type in the new IP address
Click the Change IP button.
Cycle power to the device. The IP address change activates when the device reboots.
IMPORTANT! Verify the new IP address is correct before cycling power to the device. After the IP
address changes, you must use the new IP address to access these configuration screens. Print
this page and file for your records.
1.
2.
3.
After changing the IP address of
the Ethernet Bridge device, print
this page for your records.
Tip
4. Cycle power to the Ethernet Bridge or Gateway Pro to complete this update. After the
device powers up, the changes should be registered.

P/N 134421 9
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
Login
Get ALL Command
For an existing network, perform a Get ALL for the devices and update the XML file before
changing any network parameters. The default XML file stored on the Ethernet Bridge or Gateway
Pro may not accurately represent your configured network.
From the RF Devices > Select Models screen, verify the DX80 radio devices are defined using the
Models drop-down list and the device name.
Select the Change box.
Click the Update button to send this information to the Ethernet Bridge.
Select the Get ALL checkbox for each radio device in the wireless network.
Click the Update button to retrieve configuration information from each DX80 device.
The Get ALL command retrieves the parameters on the Configure Points and I/O Linking pages.
These parameters are specific to the wireless network. The Get ALL command does not retrieve
parameters involving the host system or the wired network components.
The Get ALL command will take a few minutes to complete. Click on the Check Status button to
review the status of the Get ALL or Send ALL command.
Change, Refresh, Send, and Update Commands
Buttons commonly appearing on most configuration screens are the Change, Refresh, Send, and
Update buttons. Each of these buttons performs a slightly different task.
Change - Sends information to the Ethernet Bridge or the Gateway Pro device.
Refresh - Refreshes the screen image by updating any information on the screen that has changed
on the device.
Send - Transmits device and I/O parameters to the radio devices. The Send operation usually
requires several seconds to complete.
Update - Sends information to the Ethernet Bridge or the Gateway Pro device.
These commands do not save configuration information permanently to the XML file.
Saving Changes to the XML File
To permanently save the changes to the XML file, go to the System > Setup > Config File page
and click the Save button. Changes made by clicking an Update button are temporary and only
submitted to the Ethernet Bridge or Gateway Pro, not the XML file.
For an existing network, perform a Get
ALL for the devices and update the
XML file before changing any network
parameters.
Tip

10 P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
Login
Notes

P/N 134421 11
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
RF Devices Tab
Each tab accesses different aspects of the Web-based configurator. Use the RF Devices tab to
configure the radio network devices and I/O points.
Select Models
The Select Models tab displays the list of devices for the radio network. Use this screen to define
the wireless network devices.
Select the Get ALL checkbox and
click the Update button to retrieve
configuration information from the
DX80 devices.
For an existing network, perform a
Get ALL for the DX80 devices to
synchronize the Web Configurator
screens with the current parameters
before making any changes.
Tip
Defining a Device
To define the DX80 radio network devices:
Select the device from the drop-down list, always using device zero for the Gateway. Most
device descriptions can apply to either the Gateway or the Node.
Name the device.
Select the Change checkbox.
Click the Update button to send this information to the Ethernet Bridge.
Using the Change checkbox and Update buttons sends the only device name and model to the
Ethernet Bridge/Gateway Pro device. This will not overwrite existing I/O parameter information.
Once the devices are defined and named, select the Get ALL checkbox for each device and
click the Update button. The Get ALL command retrieves any existing parameter configuration
information from the DX80 devices and loads these settings into the Ethernet Bridge device. These
settings are not saved to the XML file. The Get ALL command will take a few minutes to complete.
Click on the Check Status button to review the status of the Get ALL or Send ALL command.
Copying a Defined Device
When setting up a radio network that includes devices with the same configuration, set up one
device and copy it using the Copy button at the bottom of the screen. Copying one device’s setup to
another device also copies the Configure Points information. To copy device parameters, fill in the
From and To boxes with the appropriate device number (listed on the left side of the table) and click
the Copy button.
1.
2.
3.
4.

12 P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
Submitting Parameters to the DX80 Devices
After defining the devices in the radio network, including the items from the Configure Points
screen, the expanded Configure Points screen, and the I/O Linking screen, check the Send ALL
box for the devices and click the Update button on the Select Models screen. This sends the I/O
point configuration information to the DX80 devices. Once the Send ALL function has begun, click
the Check Status button at the bottom of the screen. A monitoring screen displays each device’s
progress.
Other Commands
Check Status button: Click the Check Status button to watch the status of a Get ALL or Send
ALL command. Sending or retrieving information from the DX80 devices can take several minutes.
Use the Check Status button to verify the error status of the data transfer.
Get ALL: Select the Get ALL checkbox and click the Update button to pull set-up parameters from
the DX80 devices. These parameters will be loaded into the Web Configurator screens but will
not be automatically saved into the XML file. Before modifying any existing radio network devices,
always perform a Get ALL to update the Web Configurator with accurate set-up information.
Prev and Next buttons: If there are more than 16 devices in this wireless network, use the Prev and
Next buttons to display the next screen of information.
Send ALL: After defining and setting up the devices and I/O point parameters, select the Send ALL
checkbox and click the Update button to send this information to the radio network devices.
Update button: Click the Update button to send parameter information to the radio network devices
or to get parameters from the devices, depending on if the Change or Get/Send ALL checkboxes
are selected.
Saving Changes to the XML File
To save the changes to the XML file, go to the System > Setup > Config File page and click the
Save button. Changes made by clicking an Update button are temporary until the changes are
saved permanently into the configuration file.
Model Drop-Down List
The following table defines the options available in the Model drop-down list.
Option Description
None No device is present
Discrete 4DI, 4DO Discrete device with four discrete in and four discrete out.
Discrete 6DI, 6DO Discrete device with six discrete in and six discrete out.
Discrete 8DI, 4DO Discrete device with 8 discrete in and four discrete out.
Discrete 4DI, 8DO Discrete device with four discrete in and eight discrete out.
Mixed 2DI, 2DO, 2AI,
2AO
Device with two discrete in, two discrete out, two analog in, and two
analog out. The term “mixed” refers to a device with both discrete and
analog I/O.
Mixed 4DI, 4DO, 2AI,
2AO
Device with four discrete in, four discrete out, two analog in, and two
analog out.
Analog 4AI, 4AO Device with four analog in and four analog out.
Flex 2DI, 2DO, 2AI FlexPower™ Node with two discrete in, two discrete out, and two analog
in.
Flex 2DI, 2DO, 4AI FlexPower Node with two discrete in, two discrete out, and four analog in.
This description also includes the Thermocouple and RTD nodes.
M-GAGE M-GAGE™ Node
Other

P/N 134421 13
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
Configure Points
After setting up the basic model for each device, configure the I/O points. There are two ways
to access the I/O points configuration screen: 1) use the Configure Points tab; or 2) click on the
hyperlinked device number in the left column of the Select Models table to access the Expanded
Configure Points page (see the Expanded Configure Points section).
Refer to the device’s data sheet for factory default information.
If you leave any Web Configurator
screen without clicking the Change
button to submit the changes to the
Ethernet Bridge or Gateway Pro, all
changes are lost.
Tip
Setting Up I/O Points
To set up an I/O point:
Select the I/O Enabled checkbox. Any active I/O point must be enabled or the I/O is
ignored.
Select an I/O type from the I/O Selection drop-down list. The Configure Points sample
screen shows a Gateway defined with four discrete IN, four discrete OUT, two analog IN,
and two analog OUT points. Always refer to the device data sheet to determine which
discrete and which analog I/O points are active for a given device. Note, however, that
the NPN and PNP settings for discrete I/O shown on the data sheet are only default
configuration settings and can be changed.
Define any applicable parameters, e.g. sample interval, report interval, hysteresis,
threshold, or any other parameter displaying on the main or expanded view screens.
After setting up all I/O points using either the Configure Points tab or the expanded
Configure Points screen, click the Change button to submit the changes to the Ethernet
Bridge or Gateway Pro.
To send all I/O data to the devices, use the Select Models screen by selecting the Send
ALL checkbox and clicking the Update button. To send the individual I/O point changes,
use the expanded Configure Points screen and the Send button.
1.
2.
3.
4.
5.

14 P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
Parameters
The following parameters are set on the Configure Points screen.
Default Output Condition Flags: The default output conditions are a set of checkboxes to establish
device-based parameters. These default output conditions apply to all outputs on this device. After
making changes to the flags, click the Send Flags button to submit the changes to the device.
Auto-Recover - Selecting the Auto-Recover option forces the Gateway to attempt to re-
establish communications with out-of-sync nodes after a polling error condition is indicated.
The Gateway polls the failing device and must successfully communicate with the failing
node Re-Link Count times before the error condition is erased. This parameter is only used
on the Gateway. Without the auto-recover feature selected, the user must manually reset
error conditions or the host system must reset the error condition.
Gateway Link Failure - The Gateway detected a communication problem with a Node. All
linked outputs of the failing device are set to the default states.
Host Link Failure - A Modbus timeout forces all device outputs to the default states. This
parameter applies to every device that sets this flag.
Node Link Failure - A Node detected an RF link problem and set its own outputs to the
default states.
Out of Sync - When an out-of-sync condition is detected, all Node outputs are set to the
default value. This parameter applies only to the Nodes.
Power Up - All device outputs are set to the default value on initial power-up.
Delta: The delta parameter defines the change required between sample points of an analog input
before a change of state has occurred. To turn off this option, set the Delta value to 0.
Hysteresis and Threshold: The threshold defines a trigger point or reporting threshold (ON point)
for an analog input. Enter a 0 to turn off the threshold, otherwise use a specific value, e.g. 15 mA
for a 0-20 mA analog input. Threshold and hysteresis work together to establish the ON and OFF
points of an analog input.
The hysteresis value establishes how much below the active threshold (ON point) an analog input is
required to be before the input is considered
off. When set to 0, hysteresis is turned off. A
typical hysteresis value is 10% to 20% of the
unit’s range. In the example given above, the
input is considered on at 15 mA. To consider
the input off at 13 mA, set the hysteresis to 2
mA. The input will be considered off when the
value is 2 mA less than the threshold.
I/O Enable: Select the checkbox to enable
the individual I/O point. If the checkbox is not
selected, that I/O point is disabled, regardless
of what other parameters may be defined.
For efficient power usage, do not enable I/O points that are not used.
I/O Name: The I/O name field is an optional text field used to assign names to the individual I/O
points for easy reference. This name may appear in many other screens relating to the I/O point.
I/O Number: Click on the I/O # hyperlink on the far left of the screen to access an additional
screen for I/O point configuration. The expanded screen contains more I/O point parameters than is
displayed on the primary page.
I/O Selection: Select the I/O type from the drop-down list. The drop-down list includes all options
available for the entire DX80 line. Not all I/O types included in the drop-down list are applicable for
any given device. Refer to the device data sheet to determine which options are available for each
device.
Max Bad Count: The max bad count refers to a user-established maximum count of consecutive
failed polling attempts before the Gateway considers the RF link to have failed.
•
•
•
•
•
•
Threshold
On point
Time
Input Value
Input
Hysteresis point
Off point

P/N 134421 15
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
Polling Interval: The polling interval defines how often the Gateway communicates with each
Node to verify the RF link is operating. Select a value from the drop-down list, up to 1024
seconds.
Re-link Count: The re-link count is the number of completed polling messages the Gateway
receives from a failed node before the RF link is considered re-established.
Report Interval: The report interval defines how often the Node communicates the I/O status to
the Gateway. Enter the report interval in seconds, the interface rounds the value to the nearest
62.5 millisecond increment.
Setting the report interval to zero sets the system to report only when the values have changed,
also called reporting on change of state.
Sample Interval: Setting a sample interval defines how often the Node samples the I/O point
device. Enter the sample interval in seconds, the interface rounds the value to the nearest 62.5
millisecond increment.
Threshold: See Hysteresis.
Other Commands
Change button: Submits any changed parameters to the Ethernet Bridge or Gateway Pro.
Get Info button: Retrieves factory information for the selected device, such as the model
number, serial number, and production date.
Prev and Next buttons: Scrolls through the list of radio network devices.
Refresh button: Displays the most current device information.
Reset button: Resets any error conditions displayed. Until the error message is reset, the device
will not start any additional operations.
Send Flags and Get Flags buttons: Only refer to the Default Output Conditions flags, not the
I/O parameters.
Are you there?
Polling
I/O Status
Reporting
Setting the report rate to zero sets the
system to report only when the values
have changed, also called reporting on
change of state.
Tip
Sampling

16 P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
Expanded Configure Points
Most I/O point parameters are changed using the expanded view of the Configure Points tab. To
access this expanded view, which displays all parameters for the I/O point selected, click on the I/O
number hyperlink from the Configure Points tab. Several parameters on the expanded view also
appear in the standard Configure Points screen and can be modified from either screen.
Saving Changes to the XML File
To save the changes to the XML file, go to the System > Setup > Config File page and click the
Save button. Changes made by clicking the Change button are temporary until the changes are
saved permanently in the configuration file.
I/O Selection
Default Output: The default output parameters define what an I/O point is set to during selected
default conditions, such as an RF link failure.
Hold Last State: When communication fails, the I/O point retains the last value recorded instead of
the default output value.
Invert I/O: Selecting this checkbox inverts the digital representation of the I/O.
I/O Enabled: Select the checkbox to enable the individual I/O point. If the checkbox is not selected,
that I/O point is disabled. This checkbox is also on the primary screen.
I/O Type: Select the I/O type from the drop-down list. The drop-down list includes all options
available for the entire DX80 line. Not all I/O types included in the drop-down list are applicable
for any given device. Refer to the device data sheet to determine which options are available for a
given device.
“Other” Type #: Occasionally some newly designed and released devices will use I/O types not
yet listed in the drop-down list for I/O Type. When this happens, Banner Engineering applications
engineers will supply the “other” type number. Select Other from the I/O Type drop-down list and
enter the I/O type number supplied by Banner Engineering into this field.
Sampling and Reporting
Report Interval: The report interval defines how often the Node communicates the I/O status to the
Gateway. Enter the report interval in seconds, and the interface rounds the value to the nearest 62.5
millisecond increment.
For discrete inputs, setting the report interval to zero sets the system to report only when the values
have changed, also called reporting on change of state. When discrete inputs are set up with a
To save the changes to the XML file,
go to the System > Setup > Config File
page and click the Save button.
Changes made by clicking an Update
or Change button are temporary until
the changes are saved permanently in
the configuration file.
Tip

P/N 134421 17
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
non-zero report interval, a report will be transmitted at the requested time interval and also when a
change of state occurs.
All analog inputs require a non-zero report interval.
Sample Interval: Setting a sample interval defines how often the Node samples the I/O point
device. Enter the desired interval in seconds. The value is rounded to the nearest 62.5 millisecond
increment.
Report Type: Select from discrete or analog format reporting types. Analog data requires sixteen
bits while discrete data uses only one bit per I/O point. Selecting double from the list uses two
consecutive registers, each consisting of sixteen bits.
Analog Signal Conditioning
Delta: The delta parameter defines the change required between sample points of an analog input
before reporting a change. Enter a zero to turn off this option.
Hysteresis and Threshold: The threshold
defines a trigger point or reporting threshold
(ON point) for an analog input. Enter a zero to
turn off the threshold, otherwise use a specific
value, e.g. 15 mA for a 0-20 mA analog input.
Threshold and hysteresis work together to
establish the on and off points of an analog
input.
The hysteresis value establishes how much
below the active threshold (ON point) an
analog input is required to be before the
input is considered off. When set to zero,
hysteresis is turned off. A typical hysteresis
value is 10% to 20% of the unit’s range. In the example given above, the input is considered on at
15 mA. To consider the input off at 13 mA, set the hysteresis to 2 mA. The input will be considered
off when the value is 2 mA less than the threshold.
Units: Selecting the units defines the range and/or type of analog value associated with the I/O
point. Select from the following units:
Units Description
Raw Displays the raw A/D conversion data. Data ranges from 0 to 65535.
Typically only used for factory calibration.
4-20 mA Analog input unit.
0-20 mA Default analog input using 0-20 mA.
On/Off Default discrete inputs. Any discrete (digital) device
0-10 V Analog input using 0-10 V instead of current
Temp C Analog input for temperature devices such as thermocouples, RTDs,
and thermistors
Temp F Analog input for temperature devices such as thermocouples, RTDs,
and thermistors.
Temp C to mA The device converts the standard temperature input into a mA reading.
Temp F to mA The device converts the standard temperature input into a mA reading.
Selecting from the Units drop-down list automatically changes the units of several parameters,
including threshold, hysteresis, and delta. After changing the units, click the Change button to
update the units used for the parameters.
If the units are 0-20 mA, the threshold, hysteresis, and delta values are entered as milliampere
values. Selecting Temp C from the drop-down list changes the threshold, hysteresis, and delta units
to degrees Celsius.
Threshold
On point
Time
Input Value
Input
Hysteresis point
Off point

18 P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
Other Commands
Change button: Submits changes to the Ethernet Bridge or Gateway Pro.
Get button: Reads all device and I/O parameters from the DX80 device and loads them into the
Web Configurator screens. This does not save the parameters to the XML file.
Prev and Next buttons: Scroll through the I/O points for the selected device. To select a new
device, return to the main Configure Points tab (by clicking on the tab) and use the Prev and Next
buttons to select another device.
Refresh button: Displays the most current device information.
Reset button: Resets any error conditions displayed. Until the error message is reset, the device will
not start any additional operations.
Send button: After making changes to parameters on the expanded Configure Point screen, click on
the Change button to send the changes to the DX83 Ethernet Bridge or the Gateway Pro and then
click on the Send button to send these changes to the device.
After making changes to the parameters
screen, click the Change button to
submit the changes to the Ethernet
Bridge or Gateway Pro.
After submitting the changes to the
Ethernet Bridge or Gateway Pro, click
the Send button to update the radio
devices.
Tip
Ton
Toff
0 Volts
Full Power
Supply Warmup
Input sample point
Warmup Time
Digital Signal Conditioning
Sample High: The Sample High parameter establishes the minimum number of samples that an
I/O point must be detected high (1) before it is considered a change of state to a “1” value. Select a
value from 1 to 255. Set to zero to disable.
Sample Low: The Sample Low parameter establishes the minimum number of samples that an
I/O point must be detected low (0) before it is considered a change of state to a “0” value. Select a
value from 1 to 255. Set to zero to disable.
Pulse Width: The pulse width determines the number of 62.5 millisecond increments a digital
output is active (1) before returning to zero. Select 0 to disable this feature.
Battery Powered Sensor Options
Sensor Power Supply: Select a power supply for the sensor device.
Power Supply Description
External The sensor is powered from outside the Node.
Supply #1 Switched power 1 (SP1)
Supply #2 Switched power 2 (SP2)
Supply #3 Switched power 3 (SP3)
Supply #4 Switched power 4 (SP4)
Select Supply 1 through 4 to indicate the external device is powered from one of the Node’s
supplied switch power connectors.
Supply Output Voltage: The Supply Output Voltage sets the voltage required for the sensor
device. This parameter is only applicable when using the supplied switch power option.
Supply Warmup: Supply Warmup defines the length of time the switch power should be turned on
before examining the sensor’s input.

P/N 134421 19
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
I/O Linking
Each device input point can be linked or connected to any output point in the system. An output link
defined as zero for the device and zero for the output point is not connected. Valid output points on
all devices are nine through fourteen; valid devices are one through fifteen with zero reserved for
the Gateway (or Gateway Pro).
After making changes, click on the
Change button to send the changes
to the DX83 Ethernet Bridge or the
Gateway Pro, then click on the Send
button to send these changes to the
device.
Tip
Packed flag: Setting the Packed flag communicates discrete output point information more
efficiently. Instead of sending one message for each output change, discrete values are packed
into one message sent to the destination device. The packing data reduces the wireless device
traffic and improves the timing in critical applications when multiple inputs from a single device are
connected to outputs on one other device.
The Packed flag only affects the output point messages, the input message communication
is defined by each device I/O point. If a device I/O point Report Type parameter is defined as
discrete, the input reporting messages for this point are packed into one wireless message. For
greatest efficiency, all discrete inputs should be defined as a discrete Report Type.
In the sample screen shown, the Gateway input points can be mapped to any Node’s outputs.
Manually enter the device number in the Destination Device # box, then enter the I/O point number
for that destination device.
Saving Changes to the XML File
To save the changes to the XML file, go to the System > Setup > Config File page and click the
Save button. Clicking the Change button only sends the changes to the Ethernet Bridge. These
changes are temporary until saved permanently in the configuration file.
Other Commands
Change button: Submits changes to the Ethernet Bridge or Gateway Pro.
Get button: Reads all device and I/O parameters from the DX80 device and loads them into the
Web Configurator screens. This does NOT save the parameters to the XML file.
Prev and Next buttons: Scroll through the devices.
Refresh button: Displays the most current device information.
Reset button: Resets any error conditions displayed. Until the error message is reset, the device will
not start any additional operations.
Send button: After making changes to parameters on the expanded Configure Point screen, click on
the Change button to send the changes to the DX83 Ethernet Bridge or the Gateway Pro, then click
on the Send button to send these changes to the device.

20 P/N 134421
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: [phone]
SureCross™ DX80 Web Configurator
Instruction Manual
RF Devices Tab
Scaling
The Scaling screen is used for converting data. Raw data is multiplied by the Scale and added to
the Offset to produce the data appearing in the floating point register associated with the I/O point.
The floating point registers start at register 1001.
For example, thermocouple inputs are multiplied by 20 before being written to the Modbus register.
To convert this register value back to a temperature reading use the Scaling screen.
The Offset value can be used to account for errors introduced into the sensor system, such as
errors introduced because of wiring lengths in a thermocouple input system.
Other Commands
Prev and Next buttons: Scroll through the radio network devices. To advance directly to a specific
device, type the number in the Device # box and click the Update button.
Update button: Submits changed data values to the Ethernet Bridge. Changes made by clicking an
Update button are temporary until the changes are saved permanently in the configuration file.