Precision Lighting Atto Jack User manual

© 2018 Precision Lighting Ltd. We reserve the right to change details of design, materials and nish. Version 07.19
instruction manual
Atto Jack & Minipoint System
Atto Jack is a small modular display 95 CRI
LED luminaire offering 360º bearing aided
rotation and 180º tilt that uses the Precision
Lighting Minipoint system.
Atto Jack 1.2W 102lm
Atto S Jack 1.2W 102lm
Atto T Jack 1.2W 102lm
These instructions cover procedures for all
versions of Atto Jack xtures including:
Atto Jack
Atto S Jack
Atto T Jack
1. Mains supply to driver must be OFF
before connecting or disconnecting
the ttings.
2. All systems must be installed by
a suitably qualied professional
only. Installations must conform
to national installation, accident
prevention regulations.
3. Do not install any xture closer
than 150mm (6 inches) from any
combustible material. Do not install
these systems in a damp or wet
location.
4. To reduce the risk of re and burns,
do not install these systems where
exposed bare conductors can be
shorted or contact any conductive
materials. Do not conceal or extend
exposed conductors through a
building wall.
5. Install only as described in
this Precision Lighting manual.
Appropriate xings will need to be
used depending on surface material
at the installer’s discretion.
6. Ensure all connections are tight. Bad
connections can cause overheating,
arcing and potential re risk.
7. Wire supply connections must be
made with U.L or compatible testing
agency-approved connectors.
8. Luminaires may be hot, allow to
cool before touching.
9. Regular cleaning of these products is
important. Switch off at mains supply
and allow to cool before touching.
Clean ttings with a microbre cloth.
Then reconnect the power supply.
10. Always use appropriate optics and
ensure they are tted securely.
Use only Precision Lighting
recommended accessories.
11. These are constant current
xtures. For use only with an
appropriate 350mA LED driver as
recommended by Precision Lighting
33
KEY PRODUCT FEATURES
A Atto Jack luminaire
B Atto T Jack luminaire
C Atto S Jack luminaire
D Decorative Cover
E Minipoint
F Lock Washer
G Nut
A
Atto Jack Luminaire Modules
B
C
D E F G

© 2018 Precision Lighting Ltd. We reserve the right to change details of design, materials and nish. Version 07.19
1. Installation
WARNING switch off power to mains
before installation.
Cut hole ø18mm (3/4 of an inch).
Feed mains cable through hole and insert
Minipoint into hole.
Note: You will need rear access to
minipoint in order to secure it into place.
Put on lock washer and then screw on
M17 nut onto back of minipoint. Fasten
tightly to secure minipoint in place.
Screw on decorative cover with desired
nish on to top of minipoint.
1.
2. Inserting Atto Jack into Minipoint
WARNING switch off power to mains
before installation.
WARNING Do not hot plug!
Insert Atto jack luminaire into the
minipoint ensuring to line up pins with the
internal grooves.
Keep applying pressure until you hear
a soft click and the O ring is no longer
visible.
3. Locking Pan & Tilt
NOTE Only adjust luminaire position
when unlocked.
Adjust luminaire to desired position.To
lock into place, insert 0.9mm hex key
provided into pan and tilt holes then
rotate hex key clockwise.
2.
ø18
M17 Fixing
M17 Fixing
CLICK!
CLICK!
WARNING
Do not hot plug!
3.
PAN
TILT

© 2018 Precision Lighting Ltd. We reserve the right to change details of design, materials and nish. Version 07.19
4. Snoot Removal and Changing the Optic
WARNING switch off power to mains
before installation.
To remove snoot, rotate snoot
anti-clockwise and lift off.
Once snoot has been removed, the optic
can be changed. Remove optic from PCB.
To install new optic, align optic base pins
with slots on PCB and set into place.
Then place snoot over optic and rotate
clockwise to securely x to luminaire.
There should be no gap between the
snoot and the luminaire body.
5. Changing the Snoot
To remove snoot, rotate snoot
anti-clockwise and lift off.
Place new snoot over optic and rotate
clockwise to securely x to luminaire body.
There should be no gap between the
snoot and the luminaire body.
4. 5.
6. Electrical Installation
WARNING switch off power to mains
before installation.
Note: Due to small Minipoint size, drivers
must be located remotely; cut out is too
small for dimmable drivers to pass through.
See electrical instructions for wiring
schematic. Ensure circuit is wired in
series. Please only use the following
compatible drivers listed below:
• Eldoled 350mA Constant Current
20W 0-10V (PSCC-20-350-A-EL)
• Eldoled 350mA Constant Current
20W DALI (PSCC-20-350-D-EL)
Note: Do not install more than 10
minipoints in one circuit.
6.
Note: Maintain correct polarity when wiring. Incorrect wiring will
cause serious damage and will not be covered by warranty. Must
be installed according to SELV regulations.
Wire specification: 24 AWG, double insulated teflon wire.
Red = Positive Black = Negative
WARNING Do not connect or disconnect under load.
Ensure driver has not been powered for a minimum of 1 minute
before reconnecting the LED module after disconnecting. Do not
hot plug. Failure to this instruction will lead to serious damage of
the LED module and driver and will not be covered by warranty.
+Positive (Red)
from supply
+Positive (Red)
from supply
-Negative (Black)
from supply
-Negative (Black)
from supply
SINGLE MINIPOINT MULTIPLE MINIPOINTS - MUST BE WIRED IN SERIES