Pressure-Pro TPMS+ User manual








































Product Description
Pre-Installation
Setup
FAQ
Tips
Data logging
Contact details



PRESSUREPRODESCRIPTIONPRE‐INSTALLATIONINSTRUCTIONS

PressureProisawirelesselectronicTyrePressureMonitoringSystem(TPMS)thatis 
designedtodisplaycurrenttyrepressuresondemand,whethermovingorstationary. 
PressureProsystems,whichcanbeusedonallpneumatictyres,consistsoftwobasic 
components:TyreSensorsthatscrewontothevalvestemsofthetyres,andthePulse 
monitor.TheSensorsreadtyrepressuresevery7seconds(12,343timesaday),and 
transmitacodedRFsignaltothePulsemonitorevery5minutesassuringtimely 
information.IfanalarmlevelisreachedthePressureProSensorswilloverridethenormal 
updateandalertthemonitorimmediately(see“Alerts”section).Duringanalert,the 
tyrelocationlightflashesonthemonitor,thecurrentpressurereadingforthattyre 
flashes,andanaudiblealertsounds.

PressureProsystemsprovidesuserswiththemarket’smostcomprehensivealert 
schedule,withtwolowpressurealerts,ahighpressurealert,ahightemperaturealert, 
afastleakalert,andacrossaxlealert,allusercustomizable.

PressureProisamonitoringsystemandwillnotpreventtyresfromlosingpressureor 
failingbutitcanprovideearlynoticeofpotentialproblemsandalerttolowtyre 
pressuresituations.BecauseofthequirksofRFTransmissionsandinterference,no 
guaranteeofsignalreceptioncanbemade.PressureProisnotmeanttofunctionasa 
pressuregaugeorlowpressureindicator.
WhenSensorsareinstalled,theyrecognizethetyre’scurrentpressureastheirBASELINE,

thereforethetyrepressureatthetimeofinstallationisimportant.Itisrecommendedto 
installSensorswithalltyresinflatedtothemanufacturer'srecommendedpressureswhile 
thetyresare“cool”.Installationinthemorningbeforevehiclemovementisoptimal,but 
notnecessary.Installationcanbedonewhentyresare“warm”,thoughdoingso,without 
manuallyresettingthereferencepressuresmaycausefalsealerts.Ifinstallationisdone 
whiletyresare“warm”,simplyresetthereferencepressures:MENU‐>VEHICLESETTINGS
‐>REFPRESSURES‐>AXLEREFPRESSUREorVEHREFPRESSURE‐>SelectAxleorVehicle‐
>AdjustreferencepressureusingtheUP(^)orDOWN(v)arrows‐>UsetheSELbuttonto

savethenewreferencepressure

*NOTE:AXLEallowstheusertheabilitytocontrolreferencepressuresbyaxle,VEHallows 
theusertheabilitytocontrolthereferencepressurebasedonthevirtualunitorvehicle

Tyresandvalvestemsshouldbecarefullyinspectedpriortoinstallationofthesystem

toensurethattheyareingoodcondition.Defectivevalvestemsmustbereplaced.At 
times,itmaybenecessarytocleanthethreadsofthevalvestemwithawirebrushor 
tappingtoolbeforeinstallingaSensor.

Thevalvecore(thesmallvalveinsidethevalvestem)mustdepressfullyandrelease

airfortheSensortoactivate.TheSensormightnotactivateproperlyifthevalvecore 
pinisnotflushwiththeendofthevalvestem,allowingagoodreleaseofairtointerface 
withtheSensor.Itisnotunusualtofindvalvecoresinstalledtoodeep,whichwillcause 
theSensortonotactivateproperly.Thevalvecoreshouldbecentered.Checkvalve 
corebypressingtheendofathumbnaildirectlyintothevalvecoretomakesureit 
releasesa“burst”ofair.

NOTE‐WheninstallingSensorsonvehicleswithaluminumvalvestems:Newautos

mayincludefactoryinstalledTPMSSystems.NewvehicleswithTPMSutilizealuminum 
valvestemswhilePressureProSensorsaremadewithbrassthreads.Brasswillbondto 
aluminumduetothegalvanicactionbetweenthedifferentmetals.Wheninstalling 
PressureProSensorstoaluminumstems,carefullyapplydielectricgrease,ananti‐seize 
compound,tothealuminumstembeingcarefultoapplyonlytothethreadedareaof 
thevalvestem.IMPORTANT:Forvehicleswithaluminumvalve
stemsremoveSensorsevery4weekstoensurethereisnofusing.If
storingthevehicleforextended
 periods,removetheSensorsfromthealuminum
stems.



INITIALSYSTEMSET‐UP&CONFIGURATION
Firstthingsfirst!UponinitialpoweringofyourPressureProMonitor,pleasetakea 
minutetoconfigureyourunit’stimeanddateandvehicleconfiguration,and–if 
youwant–setyourcustomalertsettings.


GIVEITPOWER!
 FindyourPressurePropowercord.
 Connectyourthe6‐PinMolexconnectertoyour 
Monitor.
 Connectoppositeendtoa12Vpowersource 
(viaanaccessorylighterorhard‐wiring).

SETTIMEANDDATE:
 YourMonitorwillautomaticallytakeyoutoa 
screenpromptingyoutosetyourtimeanddate 
andwillwalkyouthroughtheset‐up.Usearrow 
keystoselectdateandtimesettings.
 Whencomplete,pressMENUtoleave‘Display’ 
screenandreturntotheVehicleSettingsMenu.
 FromVehicleSettingsMenu,Select“Alert 
Settings”andselectthealertoptionyou’dliketo 
customizeandfollowtheMonitor’spromptsto 
changealertsettings.Whenfinished,pressMENU 
untilreturnedtothemainMenu.

MONITORBUTTONFUNCTIONS

CONFIGUREVEHICLES(ifmonitoringmorethan1unit):
 Fromthemainmenu,useUParrowtoscrollto 
“VehicleSettings”andpushSEL.
 Ifyouhaveatowvehicle,oraremonitoring 
multiplevehicles,select“+/‐Vehicles”,anduse 
arrowstoscrollthroughandactivatethedesired 
numberofvehicles.Whenfinished,pressMENU 
toreturntotheVehicleSettingsMenu.

SELECTVEHICLEID(NAMETSA001):
 FromVehicleSettingsMenu,Select“VehicleID” 
andselectthevehicleyouwanttoname.
 FollowtheMonitor’sprompts(usingthearrows 
tonamevehicle).Repeatasneededforall 
vehicles.Whenfinished,pressMENUtoreturnto 
VehicleSettingsmenu.

SETYOURALERTS:




POWER
 PowerMonitor
 ReturnsMonitorto 
normaloperation

MENU
 PowerMonitor
 ReturnsMonitorto 
normaloperation


UP/DOWNARROWS
 Navigatesthrough 
screensandpositions



ALERT
 Quickaccess 
prioritizationofalerts
 Alert/WarningIndicator 
ReminderLight

SELECT
 Selects(andmoves 
forward)Monitor 
functionalityduring 
programinganduse.



PROGRAMMINGSENSORS
DONOTPUTSENSORSONTYRES.(You’dbeamazedatthenumberofcallswe 
receivewhichpromptedthisnote.)Simplyfollowthesimplestepsbelowand 
you’llbeset‐upinminutes!






1. FromthemainMenu,scrolltoandselect 
“Sensors”.







2. Select“AddSensor”.










3. Ifmonitoringmorethanoneunit,scrollto 
desiredvehicleandselect.

4.Scrollthroughandselectthedesired
vehicle
 layout(orcreateacustomlayout)
following
 Monitorprompts.

Whenlayoutisselected,yourMonitorwill 
automaticallypopulateyourconfiguration 
anddefaulttothefront,lefttyrepositionfor 
installation.Tochooseanotherposition,use 
yourarrowstoscrolltodesiredlocationthen 
pressSEL.)

5. PressSELtoinstallaSensortonoted 
location.YourMonitorwillbegin 
searchingforaSensorreading.






6. AttachaSensortothenotedlocation’s 
valvestem,andwaitforareadingto 
populate(thiscantakeupto60 
seconds).






7. Whenapressurepopulates,pressSELto 
lockintheSensorandmovetonext 
location.





Repeatsteps5‐7neededforalldesiredlocations.Whenfinished,pressthepower 
buttontwicetoplaceMonitorinoperationmode.



FREQUENTLYASKEDQUESTIONS
WHATSHOULDBEDONEIFALOWPRESSUREALERTISSOUNDED?Immediatelypullover 
andchecklowtyre.Besuretocheckvalvestemfordamage.Ifnovisualleaksarespotted, 
performasoapbubbletestontheareatolocatetheleak.

CANISTOREMYVEHICLEWITHTHEMONITORON?TheMonitordraws25mAto100mAof 
power.Itispossiblethemonitorcoulddrainthevehicle'sbatteryoveranextendedperiodof 
time.Ifstoringvehicleformorethanonemonthitisrecommendedthatyouunplugmonitor 
andremoveSensors(see“Tips”section–“VehicleStorage”).

DOESMONITORNEEDTOBEPOWEREDBYLIGHTERACCESSORY? No. Hardwiringisa
preferredmethodofpoweringasitreducesbackfeedinterference. Connecttheredwireto

a12or24‐voltDCpositivepowersource(directwiretothebatteryisnotrequired).The 
blackwireshouldbeconnectedtoagroundorchassis.WHENDIRECTWIRING,ITIS 
IMPORTANTTOINSTALLA2AMPIN‐LINE,FASTBLOWFUSEWHICHPROTECTSTHEMONITOR 
FROMVOLTAGESPIKES.MONITORSDAMAGEDDUETOHIGHVOLTAGEFROMANUNFUSED 
LINEARENOTCOVEREDBYWARRANTY.

CANMONITORBEUSEDINDEPENDENTLYONFRONTORBACKVEHICLE?
Yes–MENU‐>VEHICLESETTINGS‐>+/‐ VEHICLES‐>ScrolltodesiredVehiclestoturn

“ON”/”OFF”(Usingthe“SEL”button).Note:VehicleLayoutsettings,programmedsensors, 
referencepressuresaresavedwhenavehicleisturned“OFF”

WHATHAPPENSWHENIREMOVEASENSORTOINFLATEATIRE?Monitorwilldisplay“00”
reading. After15minutes,theMonitordisplays3dashes(‐‐‐).

WHATISTHE“REMINDER”ALERT?Afteranalerthasbeenacknowledgedwithabutton 
press,theamberTPMSAlert/WarningQuickIndicatorLightwillremainsolidasareminder 
ofthealarm/warningcondition.
HOWDOIDELETESENSORS?Menu‐>Sensors‐>DeleteSensors‐>ScrolltodesiredvehicleA‐
E(ifapplicable)‐>Scrolltodesiredtyrelocation‐>Confirmdeletion
CANIUSEASEALANTOREQUALIZERPOWDERINTHETYREWITHPRESSUREPRO?Ifusing
asealantorpowder,PressureProrecommendstheuseofafilteredvalvestem(orfiltered 
core)toreducethechanceoftheSensorbecomingclogged.

TYREPRESSURESINCREASEWHILEDRIVING‐DOINEEDTODOANYTHING?No. While
driving,itisnormalfortyrestoincreasepressureandtemperature.Ideallyforautomotive 
useanoperatingrangeof10–15%overcoldisnormal.

DOINEEDTOREBALANCEMYTYRESWHENUSINGASENSOR?TheSensorsweigh17grams,
onlargetyres(RV/Truck)thisseldomnecessitatesatyrebebalanced.Smallertyresmayrequire

arebalancing. Itisrecommendedthoughnotabsolutelynecessary.
WHENDOMYSENSORSTRANSMIT?
1. Within60secondsofscrewingSensorontothevalvestem.
2. Every5minuteswhileupdating,undernormalconditions.
3. Ata12.5%&againat25%dropfrombaselinepressure.
4. WhenaSensorisremovedfromitsvalvestem.
5. Whenanoverpressureeventislogged

IFIUNPLUGORLOSEPOWER,MUSTIREPROGRAMMONITOR?No.Settingsarealways
retainedunlessphysicallydeleted.Monitordisplays3dashes(‐‐‐)untilSensorssendanew

updatedreadingwithinthenormal5minutereportingperiod.

DURINGINSTALLATION,NO SIGNALWASRECEIVEDFROMTHESENSOR.Higherradio
frequency(RF)transmissionspropagatemostlyviastraightlinesandalongline‐of‐sight 
pathways.PressureProSensorsarerequiredtoaccomplishadauntingtask,i.e.transmit 
fromavehicle’styrestotheMonitor.IfaSensorfailstogiveapressurereading,slightly 
movetheMonitor,removethesensorfor20seconds,andreattachsensor.

AFTERINSTALLATION,PRESSUREREADINGSDROPONDISPLAY–ACTUALTYREPRESSURE
REMAINSCORRECT. TheprobablecauseispoorinteractionbetweentheSensorandvalve 
core. UnscrewtheSensorandagain,hand‐tightentheSensor. (BesuretheSensorand 
valvestemarenotcross‐threaded.) Ifconditionpersists,contactyourDistributor/Dealer.

POWERCORD&FUSE/WHYDOESN’TMYMONITORTURNON? IfyourMonitordoes 
notpower,makesurethecordisproperlyconnected. Checkthefuselocatedinthe 
cigarettelighterendofthecordbyunscrewingthesilverring(atthesilvertip)oftheplug. 
Removetheboltcenteredinthecigarettelighterend. Replaceifnecessarywitha2amp 
in‐line,fastblowfuse. IFDIRECTWIRING,ITISIMPORTANTTOINSTALLA2AMPIN‐LINE, 
FASTBLOWFUSEWHICHPROTECTSTHEMONITORFROMVOLTAGESPIKES. MONITORS 
DAMAGEDDUETOHIGHVOLTAGEFROMANON‐FUSEDLINEARENOTCOVEREDUNDER 
THEPRESSUREPROWARRANTY.

HOWDOICHANGEBETWEENMEASUREMENTUNITS?ThePressureProMonitorcan 
displaypressureandtemperaturevaluesinimperialormetricunits. Theobservationof 
incorrectvaluesforalllocationscansometimesbethefirstindicationthattheMonitorhas 
beenplacedintoanalternateunitofmeasurement. TheTPMS+Monitorshowsthe 
measurementunittotherightofallreadings. MENU‐>DISPLAY‐>MEASUREMENTUNITS
‐>PRESSUREorTEMPERATURE‐>Selectdesiredunitofmeasurement

WHATSHOULDIDOIFASENSORISLOSTORDAMAGED?ContactyourDealerorDistributor 
toorderanewSensor.

WHATHAPPENSDURINGABLOWOUT?Duringablowout(orsituationwithcompleteloss 
ofpressure)theMonitorwillsignalyouofa25%lossinpressureandread“00”.Theremay 
beinstances,suchasinacatastrophicblowout,whenaSensororstemisblownoffthetyre, 
thevehiclemovesoutofsignalrangeandnosignal(alert)isreceived.



TIPS
VEHICLESTORAGE:Ifstoringyourvehicleforextendedperiods,removetheSensors.Mark 
eachSensor’slocationsoitcanbereplacedonthesametyrelocationfromwhereitwas 
removed(eliminatingtheneedforreprogramming),oruseasectionalstoragedevice 
(similartoatackleboxdividersystem).Whenputtingthesystembackon,powerup 
Monitorfirst,nextscrewSensorsontotheiroriginalwheellocations.Pressurereadingswill 
displayonMonitor(cantakeupto1minutefornewreadingstoreport).PressurePro 
systemisnowactive.

CAUTIONS:(1)Knowthegeneralconditionoftyresbeforemovingthevehicle.Runningon 
deflatedtyrescanruinatyre.(2)The17gmSensor,onatypicalRVorlargetruck,normally 
willnotrequirethetyreberebalanced.Smallertyresmayrequirerebalancing.(3)Itis 
importanttomakesurevalvestemsareingoodcondition.

REMOTEANTENNAFORUNIQUEAPPLICATIONS:DuetotheuniquefeaturesofRFsignals 
andtheconstructionandinterferencefromelectronicsonsomevehicles,anOptional 
AntennaKitorEchoRepeatermaybeneeded.ContactyourDealer/Distributor.

RESETTINGBASELINEPRESSURE:MENU‐>VEHICLESETTINGS‐>REFPRESSURES‐>AXLE
REFPRESSUREorVEHREFPRESSURE‐>SelectAxleorVehicle‐>Adjustreferencepressure 
usingtheUP(^)orDOWN(v)arrows‐>UsetheSELbuttontosavethenewreference 
pressure

*NOTE:AXLEallowstheusertheabilitytocontrolreferencepressuresbyaxle,VEHallows

theusertheabilitytocontrolthereferencepressurebasedonthevirtualunitorvehicle
DATALOGGINGCAPABILITIES
PressureProMonitorscomestandardwithdataloggingcapabilities.IfyourMonitoris 
powered,itissavingdatasentfromyourSensors.Thedataloggingcapabilitiesallow 
driverstoviewacomplete,time‐stampedhistoryoftheperformanceoftheirtyres 
whenmanuallydownloaded.PressurePro’sTPMS+Monitorallowstransferofthe 
completedatalogbywayofamicroSD. Datalogswillexportin.xmlformat,and 
workswithmanyprograms. PressureProsuggestsMsExcel.


ExportInstructions:MENU‐>VEHICLESETTINGS‐>Logging(ScrollDOWN(v)for

moreoptions)‐>Logging‐>EXPORTLOG

Featuresandbenefitsofthedataloggingfunction
 Timestampeddata
 Setloggingintervalfrom1to99minutes
 Canlogupto45daysofdataformostconfigurationsandloggingintervals
 Displaysdataforeachtyre/sensorseparately
 Summaryreporttoviewallsystemalertsduringcurrentloggingperiod
 Dataprovidedpereachloggingevent
1. SensorSETofReferencepressure(whichalertsarebasedupon)
2. Pressureforeachtyre
3. Tyretemperature
4. Signalstrengthfromeachposition
5. Allalerts

Whatyoucaninferfromthedata
1. Whenvehiclestartsmoving.
2. Whenvehiclecomestostopforlongperiodsoftime(>15minutes).
3. Dangerousoperatingconditions. Temperatureisdisplayedatalltimes,specifically 
whenthetyretemperaturehasreachedthedangerzoneof100°C(>200°F). Tyre 
rubbercompoundsbegintobreakdownatthesetemperatures.
4. Ifpropercoldpressuresarebeingmaintained.
5. Whensensorsareremovedfromtyreandforhowlong.
6. Whenatyrebegantoloseair,whenitalarmedandhowlongitraninanalert 
condition.
7. Whendataloggerwasturnedoff.(OptionallyPasswordControlled)
8. Validationofdriverstatements.




SENSOR
SPECIFICATIONSLIMITEDWARRANTY
ONEYEARLIMITEDWARRANTY : SubjecttothelimitationsandexclusionssetforthinthisLimited 
SensorTransmitRangeApprox.300feet(Line‐of‐Sight)+
OperatingFrequency433.92MHzFM
OperatingTemperatureRange‐40°C/‐40Fto+150°C/302F

SensorWeight.66oz.(17grams)
SensorDimensions1.01"Hx1.11"Dia.
SensorBatteriesInternal,sealedunit
SensorPressureRange8to299PSI/55to1999kPa/1to20.3BAR 
SensorLowVoltageShutdown2.2Volts
Accuracy+/‐3%rangeupto120PSI
+/‐5%from120PSIup


MONITOR
MonitorPowerRequirements12or24VDC;draws50mAinstandby. 
MonitorDimensions4.5”Wx3.0”Hx1.0”D
MonitorTyrePositions1to80wheelpositions

PressureAlertLevels/OptionsAlertsarecompletelycustomizable.For
convenience,yourMonitorcomesfactoryset

atthefollowinglevels.
i. LowPressure=12.5%and25%loss
ii. HighPressure=24%increase(user 
configurable)
iii. CrossAxleAlert=10%variation(user 
configurable)
iv. FastLeakAlert=OFF(userconfigurable) 
Temp.AlertLevels/Options200°F(UserConfigurable)
BuiltinAdvancedCapabilitiesRS232,J1939&USBdatafeeds
Datalogginganddownload


USLetterPatent#6,453,737(OtherPatentsPending)
PressureProsystemscomplywithPart15,ClassBoftheFCCRules.

ProductsusingRFsignalsaresubjecttointerferencecausingalossofsignal.Reception 
dependsontheenvironmentandconditionspresentatthetimeofuse.PressureProisa 
devicemeantfordisplayingtyrepressuresandhasbeendesignedtobeasreliableas 
possiblewiththeuseofRFtransmissions. Thereisnoguaranteeofsignalreception.This 
devicecomplieswithpart15oftheFCCrules.Operationissubjecttothefollowingtwo 
conditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemust 
acceptanyinterferencereceived,includinginterferencethatmaycauseundesired 
operation.PressureProisadevicemeantfordisplayingtyrepressures.
Warranty,PressureProiswarrantedbyAdvantagePressurePro,LLC(hereinafter“APP”)against 
defectsinmaterialorworkmanshipthatresultinaproductfailureduringtheone‐yearperiod 
followingthedateofpurchase.ThisLimitedWarrantyappliesonlytoclaimsmadebytheoriginal 
enduser(hereinafter“you”)andcannotbeassigned,transferredorconveyedtoanysubsequent 
users. 

EXCLUSIONSFROMCOVERAGE:ThisWarrantydoesnotapplytoanyclaimsarisingfrommisuse, 
abuse,unauthorizedrepairoralteration,circumstanceswherePressureProisimproperlyinstalledor 
improperlywiredcontrarytoPressureProproductinstructions;ordamageordefectattributableto 
fireorothercasualty,including,withoutlimitation,actsofGodorexposuretoabrasiveorcorrosive 
materialsorpollutants,orattributabletocollisionorotheraccidentsinvolvingvehiclesuponwhich 
thePressureProisinstalled.RemovaloralterationoflabelsvoidsproductWarranty.Only 
PressureProaccessoriesmaybeusedwithPressureProproducts.Theuseofotheraccessorieswith 
PressureProproductisprohibitedandcandamagethePressureProproduct.Warrantyproblems 
causedbyuseofaccessoriesnotsuppliedbyAPPwillnotbecoveredunderthewarranty. 
LIMITATIONS:APPexpresslylimitstheapplicabilityoftheimpliedwarrantyofmerchantabilityand 
theimpliedwarrantyoffitnessforaparticularpurposetotheone‐yearwarrantyperiodasprovided 
herein.Somejurisdictionsdon’tallowlimitationsonhowlonganimpliedwarrantylasts,sothe 
abovelimitationmaynotapply. 
Totheextentpermittedbylaw,theremedyofrepairorreplacementdiscussedbelowisthesole 
remedyavailabletotheenduserunderthisLimitedWarranty.THISLIMITEDWARRANTY 
SPECIFICALLYEXCLUDESALLINCIDENTAL,SPECIAL,ORCONSEQUENTIALDAMAGES.SOME 
JURISDICTIONSDONOTALLOWTHEEXCLUSIONORLIMITATIONOFINCIDENTALORCONSEQUENTIAL 
DAMAGES,SOTHEABOVELIMITATIONOREXCLUSIONMAYNOTAPPLYTOYOU.Totheextent 
permittedbylaw,APP’sliabilityforPressureProwillnotexceedthepurchasepricepaidforthe 
product. 
NOTICE : Thiswarrantygivesyouspecificlegalrights,andyoumayalsohaveotherrights,whichvary 
indifferentjurisdictions. 
EXCLUSIVEAGREEMENT : Totheextentpermittedbylaw,thisOneYearLimitedWarrantyisa 
completeandexclusivestatementofthewarranties,whichapplytothePressureProproduct;there
areno
 expressorimpliedwarrantiesbeyondthoseexpresslystatedabove.Noemployee,agent,
dealeror
 otherpersonisauthorizedtogiveanywarrantiesonbehalfoftheAPP,exceptas
authorizedin
 writing. 
STATUTEOFLIMITATIONS:Totheextentpermittedbylaw,inpurchasingthePressureProyouagree 
thatanyactionforbreachofcontractorwarrantymustbecommencedwithinoneyearafterthe 
causeofactionhasaccrued. 
PROCEDURE : Intheeventthataproductfailurecoveredbythiswarrantyoccurswhilethiswarrantyis 
ineffect,APPwill,atitsoption,either:(a)repairthedefectiveunit;(b)replacethedefectiveunit  
withanewunit;or(c)replacethedefectiveunitwitharefurbishedunit.APPwillshipyourrepaired, 
new,orrefurbishedunittoyouwithoutchargeforparts,service,oranyothercost(exceptshipping 
andhandling)incurredbyAPPoritsrepresentativesinconnectionwiththeperformanceofthis 
warranty.FailedunitscoveredunderthiswarrantymustbesentbyyoutoAPPwithshippingprepaid 
byyou.Youareresponsibleforallcostsincurredintheremoval,reinstallation,andshippingofthe 
unit.Acopyofthesalesslipreceivedbyyouatthepointofpurchaseoftheunitmustaccompany  
thereturnedunit.ContactyoursupplierforallWarrantyReturnAuthorizations. 

AustralasianMasterDistributor
TyreSafeAustralia
Contact;DavidHorne
+61(0)439830930
[email protected]
http://www.tyresafe.com.au
PRESSUREPROTPMS
FORORDERINGORTECHNICALASSISTANCE,CONTACT 
WARRANTYAUTHORIZATION
Forreturnauthorizationorwarrantyissues
CallTyreSafeAustralia+61(0)439830930
IMPORTANT:StandardWarrantyasperlegislationapplies,12month
workmanshipandmanufacturingconditions.
ProudlyDevelopedandManufacturedintheUSA